Tender For Supply, Installation, Testing And Commissioning Of Vrv Ac System Work Of New Iucaa-2 Building At Iucaa, Pune ; 1 Supplying, erecting, testing and commissioning of10 HP VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100%capacity at 47° C, non stop cooling even at 55° C and coefficient of performance (COP) 4.00 to 4.80 at AHRI condition, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor having in built logic to automode to transfer on the remaining outdoor unitsof that system , air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. The rates are inclusive of first fill refrigerant gas and oil required, galvanised stand for outdoor units with SS fasteners and serrated rubber pads. The panel must be 100% compatible with BMS. The units must also be provided with self addressable control system for control of indoor and outdoor machines. The capacity and power consumption curves, deration/correction factor curves / charts for indoor temperature and piping derations must be submitted with offer, along with duly filled-up datasheet in the attached format. Deration Chart table highlighted at 47 Degree Celsius must be provided with the Technical Data Sheet/Technical Bid Form. 2 Supplying, erecting, testing and commissioning of14 HP VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100%capacity at 47° C, non stop cooling even at 55° C and coefficient of performance (COP) 4.00 to 4.80 at AHRI condition, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor having in built logic to automode to transfer on the remaining outdoor unitsof that system, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. The rates are inclusive of first fill refrigerant gas and oil required, galvanised stand for outdoor units with SS fasteners and serrated rubber pads. The panel must be 100% compatible with BMS. The units must also be provided with self addressable control system for control of indoor and outdoor machines. The capacity and power consumption curves, deration/correction factor curves / charts for indoor temperature and piping derations must be submitted with offer, along with duly filled-up datasheet in the attached format. Deration Chart table highlighted at 47 Degree Celsius must be provided with the Technical Data Sheet/Technical Bid Form. 3 Supplying, erecting, testing and commissioning of16 HP VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100%capacity at 47° C, non stop cooling even at 55° C and coefficient of performance (COP) 4.00 to 4.80 at AHRI condition, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor having in built logic to automode to transfer on the remaining outdoor unitsof that system, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. The rates are inclusive of first fill refrigerant gas and oil required, galvanised stand for outdoor units with SS fasteners and serrated rubber pads. The panel must be 100% compatible with BMS. The units must also be provided with self addressable control system for control of indoor and outdoor machines. The capacity and power consumption curves, deration/correction factor curves / charts for indoor temperature and piping derations must be submitted with offer, along with duly filled-up datasheet in the attached format. Deration Chart table highlighted at 47 Degree Celsius must be provided with the Technical Data Sheet/Technical Bid Form. 4 Supplying, erecting, testing and commissioning of18 HP VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100%capacity at 47° C, non stop cooling even at 55° C and coefficient of performance (COP) 4.00 to 4.80 at AHRI condition, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor having in built logic to automode to transfer on the remaining outdoor unitsof that system, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. The rates are inclusive of first fill refrigerant gas and oil required, galvanised stand for outdoor units with SS fasteners and serrated rubber pads. The panel must be 100% compatible with BMS. The units must also be provided with self addressable control system for control of indoor and outdoor machines. The capacity and power consumption curves, deration/correction factor curves / charts for indoor temperature and piping derations must be submitted with offer, along with duly filled-up datasheet in the attached format. Deration Chart table highlighted at 47 Degree Celsius must be provided with the Technical Data Sheet/Technical Bid Form. 5 Supplying, erecting, testing and commissioning of20 HP VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100%capacity at 47° C, non stop cooling even at 55° C and coefficient of performance (COP) 4.00 to 4.80 at AHRI condition, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor having in built logic to automode to transfer on the remaining outdoor unitsof that system, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. The rates are inclusive of first fill refrigerant gas and oil required, galvanised stand for outdoor units with SS fasteners and serrated rubber pads. The panel must be 100% compatible with BMS. The units must also be provided with self addressable control system for control of indoor and outdoor machines. The capacity and power consumption curves, deration/correction factor curves / charts for indoor temperature and piping derations must be submitted with offer, along with duly filled-up datasheet in the attached format. Deration Chart table highlighted at 47 Degree Celsius must be provided with the Technical Data Sheet/Technical Bid Form. 6 Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type room/indoor unit (IDU) of nominal cooling capacity 1.0TRto 1.25TR having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be of decorative slim dimension suitable indoor wall mounting. The indoor unit shall also have an electronic control console. The unit shall be suitable for wall mounting and provided with suitable mounting brackets with any additional refrigerant and oil charge as per requirement during installation complete. 7 Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type room/indoor unit (IDU) of nominal cooling capacity 2TRto 2.2TR having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be of decorative slim dimension suitable indoor wall mounting. The indoor unit shall also have an electronic control console. The unit shall be suitable for wall mounting and provided with suitable mounting brackets with any additional refrigerant and oil charge as per requirement during installation complete. 8 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 1.0TR to 1.3TRhaving EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 9 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 1.5TRto 1.8TRhaving EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 10 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 2.0TR to 2.3TRhaving EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 11 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 2.6TR to 2.8TR having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 12 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 3.0TR to 3.2TR having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 13 Supply, installation, testing and commissioning of VRF/VRV based ceilingsuspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 3.3TR to 4.0TR having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. 14 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 1 way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 1.4TR to 2.0TR having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation complete. 15 Supplying, erecting, testing and commissioning of 2 core shielded cable complete asper specification no.FF-PA/MCC 16 Supplying and erecting HMS uPVC FRLS grade conduit 20 mm dia. with uPVC FRLS accessories on wall / ceiling as per specification No:WG-MA/CON. 17 Supplying and installation of high pressure grade required size copper connection Y or T- Joints/ refnet complete for indoor & outdoor units erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditioning system.(consider two nos. of refnets in each set) 18 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 41.3mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 19 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 34.9mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 20 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 28.6mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 21 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 22.2mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 22 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 19.1mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 23 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 15.9mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 24 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 12.7mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 25 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 9.5mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 26 Supplying,laying/fixing,testingandcommissioningof appropriatenominalrefrigerantcopper pipe of 6.4mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. 27 Supplying and erecting 20/25 mm (ID/OD) Unplasticizedpolyvinyl chloride pipe (UPVC), thickness 2.6 mm conforming to IS 15778 (CTS Series) with necessary UPVC fittings and solvent cement for Solar Water Heater System as per specification No. ESD-HWP/UPVC 28 Supplying and erecting 25/32 mm (ID/OD) Unplasticizedpolyvinyl chloride pipe (UPVC), thickness 3.2 mm conforming to IS 15778 (CTS Series) with necessary UPVC fittings and solvent cement for AC unit drain piping 29 Supplying and erecting 32/40 mm (ID/OD) Unplasticizedpolyvinyl chloride pipe (UPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary UPVC fittings and solvent cement for AC unit drain piping 30 Supplying and erecting 40/50 mm (ID/OD) Unplasticizedpolyvinyl chloride pipe (UPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary UPVC fittings and solvent cement for AC unit drain piping 31 Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware. 32 Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware. 33 SITC offactoryfabricatedGSSsheetmetal rectangular/roundductingcompletewithneoprenerubbergaskets,elbows,splitterdampers,vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - 22 G 34 SITC offactoryfabricatedGSSsheetmetal rectangular/roundductingcompletewithneoprenerubbergaskets,elbows,splitterdampers,vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - 20 G 35 Supplying & applying of adhesive thermal insulation for supply / return airduct with19 mm nitrilerubberinsulation havingR-value as per the prevailing provisions in ECBC-2007. 36 SITC of Inline cabinet type fan with galvanised steel cabinet,forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 1850 CFM @ 15 mm SP FA FAN With EU5 Filter -Basement+ Ground flr 37 SITC of Inline cabinet type fan with galvanised steel cabinet,forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 440 CFM @ 15 mm SP FA FAN with EU5 Filter -Basement Floor 38 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCK series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 3500 CFM @ 25 mm ESP FA FAN With EU5 Filter - Basement 39 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 900 CFM @ 20 mm ESP FA FAN With EU5 Filter - Second Floor 40 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 600 CFM @ 25 mm ESP FA FAN With EU5 Filter - First Floor 41 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 200 CFM @ 25 mm ESP FA FAN With EU5 Filter - Ground Floor 42 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CSD/CSK series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 2540 CFM @ 25 mm ESP FA FAN With EU5 Filter - First Floor 43 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 1220 CFM @ 25 mm ESP FA FAN With EU5 Filter - Second Floor 44 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 1850 CFM @ 25 mm ESP EA FAN - Basement 45 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 1750 CFM @ 25 mm ESP EA FAN - Basement 46 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CSD/CCK series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 3030 CFM @ 25 mm ESP FA FAN Ground flr 47 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CSD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 150 CFM @ 25 mm ESP EA FAN - Ground Floor 48 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CSD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 3240 CFM @ 25 mm ESP EA FAN- Terrace Floor 49 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 200 CFM @ 15 mm ESPEA PROPELLER FAN - Second Floor 50 SITC of Inline cabinet type fan with galvanised steel cabinet, forward curved centrifugal fan. The fan shall be with hanger and cabinet support. Fan shall be suitable for Specified mm ESP. Single/Three Phase, Suitable KW motor, Kruger make CCD series or equivalent. The fan shall have its own starter panel with fan speed control regulator etc. The starter panel shall have BMS compatibility for ON & OFF. The panel shall also have the terminal junction / Marshalling box for terminating all control / Sensor cables Capacity 300 CFM @ 15 mm ESPEA SITC of Inline FAN -Ground+First Floor 51 SITC of G I Fresh Air Louvers & Exhaust Air Louvers with birdmesh in SS construction 52 Supplying and erecting galvanised/MS iron work, sheet metal work consisting of CRCA/GI sheets, various sections of galvanised/MS iron, plates,rods, L angles, C Channels etc. for panel board/OD Foundation or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears/OD units or as per directions by the authority. 53 Supplying and erecting circular flexible/rigid PVC pipe duct of size 100mm dia, 4mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc. with sealing with provided control/air flow regulating valves / dampers, filters at position complete. 54 Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 54 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB 55 Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 54 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB 56 Supplying, erecting and marking four pole isolators only switch version of miniature circuit breakers of 80/100Ain provided distribution board. 57 Supplying, fixing and commissioning 4 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO 58 Supplying, fixing and commissioning 4 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO 59 SITC of CAV Boxes for Fresh Air Control to Cassette Unit 30 - 90 CFM self-powered volume flow controllers for the control of supply air or extract air in constant air volume systems. 60 SITC of Aluminium ABS Plastic Disc Valve 100 mm Dia 61 SITC Of Aluminium Powder Coated Fresh Air Diffuser with Damper size - 300 mm X 300 mm 62 Supplying, erecting & terminating FRLS XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100V, 4 core 10 sq. mm. copper conductor complete erected with double compressed glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification. 63 Supplying, erecting & terminating FRLS XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. copper conductor complete erected with double compressed glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU. 64 Supplying, erecting & terminating FRLS XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 35 sq. mm. copper conductor complete erected with double compressed glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU. 65 Supplying and erecting aluminium powder coated door transfer linear grill of 700x 150mm suitable door thickness size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45°.
