Tender For Civil Works At Spd Building Ecil, Hyderabad - 1 1 Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. 2 2 Removing of the existing damaged vinyl planks flooring (wooden floor) incluidng disposal of material within 1 KM lead etc., complete and as directed by Engineer-in-charge. 3 3 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-incharge. 4 4 Providing and laying 1.5mm thick vinyl planks for flooring as per user s requirement using one or more approved colours laid in single layer full sheets over the existing flooring, laying the sheets by applying rubber adhesive of fevicol 305/505/SR-998 or equivalent, rolling the same such that there will not be any air gaps, jointing neatly, cleaning the top surface etc., including cost and conveyance of material and all incidental charges etc., complete and as directed by Engineer-in-charge. 5 5.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size 6 6.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 7 7.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) 8 7.2.1 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) 9 8.1 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides 10 9.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 11 10 Providing etching on float glass panes in aluminium work in approved pattern etc., complete and as directed by Engineer-in-charge. 12 11.1 Providing and fixing aluminium handles, ISI marked powder coated minimum thickness 50 micron on aluminium of required colour or shade with necessary screws etc. complete : 125 mm 13 12.1 Providing and fixing aluminium tower bolts, ISI marked (powder coated minimum thickness 50 micron on aluminium of required colour or shade, with necessary screws etc. complete : 300x10 mm 14 13 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 15 14 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 16 15.1 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steof size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceidirected by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulos etc. Note: The detailed scope of work is attached as document, you are requested to quote as per the detailed scope of work 17 17 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 18 18.1 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 19 19.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 20 20. Supply and fixing of 6mm thick rubber conductive mat flooring with 505 fevicol rubber adhesive, copper strip grip at 1200x1200mm filling the joints with silicon sealent etc., complete with standard installation and specifications as per the instructions of Engineer-in-charge. 21 21. Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved 22 22. Supply of name plates for main entry of SPD made with 3mm thick white colour ACP sheet blue olour vinyl and letters with laser cutting including cost of labour charges for positioning the vinyl and pasting properly and peeling the letters etc., with including the transport charges and as directed by Engineer-in-charges 23 23 Supplying and fixing vertical venetian blinds 4 width as per user s requirement with necessary accessories and approved colour etc., complete and as directed by Engineer-in-charge. 24 24. Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 25 25 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 26 26.1. Distempering with 1st quality acrylic distemper (ready made) VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer s specification. One or more coats on old work 27 27.1. Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work 28 28.1. Wall painting with premium acrylic emulsion paint of interior grade, VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats 29 29.1. Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). 30 30.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer 31 31 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 32 16 Under deck insulation for exposed roof with 50mm thick TF quality 16Kg/cum density thermocole with GI washers
