Tender For Procurement Of Audio And Collaborative Visualization Center , Group A - Sitc Of Audio & Control System , Sitc Of Ceiling Tile Microphone , Sitc Of Audio Processor/Dsp , Sitc Of Celling Mounted Speakers , Sitc Of Dual-Channel Audio Amplifier , Sitc Of 4K Video Conferencing Camera , Sitc Of Control System With 2Nos Touch Screen/Panel , Sitc Of Av Controller With Complete Accessories , Sitc Of Hdmi Transmitter , Sitc Of Hdmi Receiver , Sitc Of 8X8 Matrix Hdmi Av Switcher , Sitc Ofcollaborative Visualization System , Sitc Of Wireless Presentation & Conferencing System , Sitc Of Multi-Windows Image Processor/ Display/Data Wall Controller , Sitc Of High Resolution Display System , Sitc Of Power Distribution Unit , Sitc Of Structure For Led Wall , Sitc Of Mounting Stand For Cameras , Sitc Of Conferencing Speakerphone , Cable Set And Accessories , Sitc Of 24 U 19” Rack , Onsite Oem Warranty Five Years From The Date Of Completion Report Signed By Iit Jammu. , Vendor Will Do Any Civil/Electrical /Earthing Work Involved In Installing Products On-Site. , Any Other Equipment Or Accessories Required As Per The Site (If Needed) , Sitc Of Interior Acoustic Works , Providing And Fixing Grid Ceiling Systems With Ceiling Tiles Of Armstrong/Saint-Goblin/ India Gypsum Or Equivalent As Per Following Specifications. Rate To Include All Fastening Accessories With Approved Finishes. Ceiling Tiles Shall Be Approved Make Tegular Edge Tile S Of Size 600Mmx600mm, Of Approved Shade/Colour. Tile Shall Render A Nrc Level Of 0.5-0.6. Suspension System Shall Be Manufacturer Specific Stitched Exposed Grid System With 24Mm Wide T-Section Flanges. Installation To Comprise Of Main Runners Spaced At 1200Mm Centres Securely Fixed To The Structural Soffit By Approved Hangers At 1200Mm Maximum Centres And Not More Than 150Mm From Spliced Joints. The Last Hanger At The End Of Each Main Runner Should Not Be Greater Than 600Mm From The Adjacent Wall. Flush Fitting1200mm Long Cross Tees To Be Interlocked Between Main Runners At 600Mm Centres To Form 1200Mmx600mm Modules. Cut Cross Tees Longer Than600mm Require Independent Support. 600Mmx600mm Modules To Be Formed By Fitting 600Mm Long Flush Fitting Cross Tees Centrally Between The 1200Mm Cross Tees. Perimeter Trim To Be 24Mm Exposed Trim Manufacturer Specific Sized Wall Angle Of Approved Colour, Secured To Walls At 450Mm Maximum Centres. Flush Fitting1200mm Long Cross Tees To Be Inter Locked Between Mainrunnersat600mm Centres To Form 1200Mmx600mm Modules. Cut Cross Tees Longer Than 600Mm Require Independent Support. 600Mmx600mm Modules To Be Formed By Fitting 600Mm Long Flush Fitting Cross Tees Centrally Between The 1200Mm Cross Tees. Perimeter Trim To Be 24Mm Exposed Trim, Manufacturer Specific Sized Wall Angle Of Approved Colour, Secured To Walls At 450Mm Maximum Centres. , Painting With Acrylic Emulsion Paint, Having Voc (Volatile Organic Compound ) Content Less Than 50 Grams/ Litre, Of Approved Brand And Manufacture, Including Applying Additional Coats Wherever Required, To Achieve Even Shade And Colour With Two Coats , Sitc Of Wall Treatment , Providing And Fixing Gi Gyp Steel Ultra-Frame Work For Wall Panelling As Per Design Drawing Consisting Of Floor Channel Of Size 50X32x32 X0.5Mm Thick At Bottom And Top Fixed With 35 Mm Nylon Sleeves And 35 Mm Screw. Further Fixing Gi Stud 48X34x36x0.5 Mm Thick @600Mm C/C Vertically. The Framework To Be Filled With 50Mm 1200Gsm Non-Woven Thermal Bonded Polyester Wadding ( Make Nowofill) Held In Position With 18 Mm Gi Checken Mesh Of 24Swg With Drive All Screws And Oversize Washers. Finally Fixing Over It Horizontally 80X26x51x0.5 Mm Thick G.I. Gyp Ceiling Section Placed @600Mm C/C Or Wherever Required As Per Design Drawings. The Frame To Be Fixed To The Walls By Means Of Angle Holdfasts Or Cleats Of Required Size Complete With Expandable Anchor Fasteners Of 65X10mm Dia Fixed On Each Vertical Member @1000Mm C/C. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials Engineer In Charge. , Providing And Fixing 2Nd Class Teak Wood Plain Lining Tongued And Grooved, Including Wooden Plugs Complete With Necessary Screws And Priming Coat On Unexposed Surface.25 Mm Thick. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. , Providing And Fixing Is 303 Bwrcommercial Ply Of Commercial Ply Of Required Thickness For Wall Lining With Necessary Screw, Priming Coat On Un-Exposed Surface Complete As Per Drawing And Direction Of Iit Jammu Officialss. Recommended Make: Duro, Century, Archid-Ply. The Ply To Be Fixed To The Existing Gi Frameworks (Frameworks To Be Paid Separately) At All Heights.12Mm Thick Commercial Ply. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. , Extra For Making 18% Perforations In The 8Mm Ply. , Providing And Fixing Is 303 Bwrcommercial Ply Of Commercial Ply Of 19Mm Thickness For Screen Support With Necessary Screw, Priming Coat On Un-Exposed Surface Complete As Per Drawing And Direction Of Iit Jammu Officials. Recommended Make: Duro , Century , Merino . The Ply To Be Fixed To The Existing Gi Frameworks (Frameworks To Be Paid Separately) At All Heights.8Mm Thick Commercial Ply. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. , Providing & Fixing Of Pet 3D Designer Acoustic Panels Of 9Mm Thickness Cut Into Sizes And Jalis As Per The Design With 3Mm Acoustic Felt Backing Complete As Per The Design Drawings. The Panels To Be Gluer Over The Existing Perforated Fr Ply. The Pet Panels To Be Fire Class1. The Work Shall Be Executed As Per Drawings, Specifications & Instructions Of Iit Jammu Officials. , Providing & Fixing At All Heights On Ceiling Wood Based Slats Laminated Panels (Bollard/ Gyptec/ Versatile Acoustic) Having Nrc Upto 0.75 With Lineal Perforations. The Size Of Lineal Panels Is 2400 X 128X 16Mm With A Pitch Of 16 Mm. The Slats To Have A Groove Of 2Mm. The Back Panels To Have Circular Perforations (8-10Mm) Dia Randomly With A Non-Woven Fabric Covering Of 0.2Mm. The Lineal Panels To Have Tounge & Groove Joints And Fixing Arrangements For Seamless Continuity. The Panels To Be Fixed On The Gi Framework With Impalers As Per Manufacturers Recommendations (The Gi Framework To Be Payable). The Work To Be Done Complete As Per Specifications & Instructions Of Iit Jammu Officials. , Steel Work In Built Up Tubular (Round, Square Or Rectangular Hollow Tubes Etc.) Trusses Etc., Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer, Including Welding And Bolted With Special Shaped Washers Etc. Complete. Hot Finished Seamless Type Tubes , Polishing In High Gloss/Matt Finish Melamine Clear Polish On Wood Work In Required Color/Wooden Shade Texture With Following Process In The Sequence As Detailed Below: 1. The Surface To Be Polished Is Rubbed With Sand Paper 80/120 No. And Then With Sand Paper Of 160/180 Nos. 2. Applying Two Coats Of Sealer With Spray Gun And Allowing Sufficient Drying Time For 1St Coat And 2Nd Coat Is Allowed To Dry For 8 To 12 Hrs. 3. On Drying Of Sealer Coat, Wet Rubbing With Emery Cloth Of Finer Grading With Ample Water To Remove Excess Sealer Layer And Make The Surface Further Smooth After This Wet Rubbing, Then Surface Is Applied With Special Grade Melamine Fillers To Fill All The Small And Big Holes/Grooves Etc. Filler Coat To Be Allowed To Dry For 4 To 6 Hrs On Which Again A Light Wet Rubbing Is Done This Surface Is Further Allowed To Dry For 12 Hrs. 4. On This, 1St Coat Of Melamine Polish Is Applied With Spray Gun Using Melamine Clear Polish And Melamine Thinner In Required Proportion. This 1St Coat Is Allowed To Dry For 24 Hrs Then This Dry Surface Is Again Fine Wet Rubbed Smooth, Which Is Further Allowed To Dry For 12 Hrs. The Final Melamine Polish Is Applied With Compressor Pressure Spray Gun Using Melamine Clear Polish And Melamine Thinner Mixed In Required Proportion Complete As Per Direction Of Iit Jammu Engineer-In-Charge. (Final Coat To Be Done In 1 Or 2 Layers Without Gap Of Time.) , Sitc Of Flooring Work , Providing And Laying 100 % Nylon Multilevel Loop Pile Carpet Tiles Of Wels Pun/Wonder Floor/Excel Or Equivalent Shade Approved By Architect In 8Mm Thick Quality Having 100 % Solution Dyed, Of 1/12Th Gauge Having Pile Thickness Of 3Mm Total Thickness 8 Mm. Pit Should Be Antimicrobial And With Soil/Stain Protection. Tile Size 50Cm X 50Cm And Tile Backing Should Be Of Glass Bac Having Minimum 32 % Recycle Content Including Minimum 30 % Post-Consumer Content. Product Should Comply With Cri Green Label Plus Standards. Floor Carpet For Inside Hall Flooring Which Shall Be Free From Dust Completed As Per Architect Instruction And Design/Approval. , Sitc Of Electrical Works , Wiring For Light Point/ Fan Point/ Exhaust Fan Point/ Call Bell Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessed Medium Class Pvc Conduit, With Modular Switch, Modular Plate, Suitable Gi Box And Earthing The Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc. As Required. , Wiring For Group (Loop) Light Point/Fan Point/Exhaust Fan Point / Call Bell Point Without Switch Etc.) With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface/ Recessed Medium Class Pvc Conduitand Earthing The Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc. As Required . , Wiring For Circuit/ Sub Main Wiring Along With Earth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface/ Recessed Medium Class Pvc Conduit As Required. 2 X 2.5 Sq. Mm + 1 X 2.5 Sq. Mm Earth Wire , Supplying And Fixing 25 Mm Dia Ms Flexible Pipe With Pvc Coating Along With All Ancillaries And Accessories Like Coupler Etc. As Required. , Supplying And Fixing Of Following Sizes Of Medium Class Pvc Conduit Along With Accessories In Surface/Recess Including Cutting The Wall And Making Good The Same In Case Of Recessed Conduit As Required I. 25Mm , Supplying And Fixing Of Following Sizes Of Medium Class Pvc Conduit Along With Accessories In Surface/Recess Including Cutting The Wall And Making Good The Same In Case Of Recessed Conduit As Required Ii. 32Mm , Supplying And Fixing Following Modular Switch/ Socket On The Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Required. I. 15/16 A Switch , Supplying And Fixing Following Modular Switch/ Socket On The Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Required. Ii. 6 Pin 15/16 A Socket Outlet , Supplying And Fixing Following Size/ Modules, Gi Box Along With Modular Base & Cover Plate For Modular Switches In Recess Etc. As Required I. 3 Module (100Mmx75mm) , Supplying And Fixing Following Size/ Modules, Gi Box Along With Modular Base & Cover Plate For Modular Switches In Recess Etc. As Required Ii. 6 Module (200Mmx75mm) , Mcbs S/F C Series, Sp Mcb: Supplying And Fixing 5 Amps To 32 Amps Rating, 240/415 Volts, C Curve, Miniature Circuit Breaker Suitable For Inductiveof Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. I. Single Pole , Mcbs S/F C Series, Sp Mcb: Supplying And Fixing 5 Amps To 32 Amps Rating, 240/415 Volts, C Curve, Miniature Circuit Breaker Suitable For Inductiveof Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. Ii. Doublepole , Mcbs S/F C Series, Sp Mcb: Supplying And Fixing 5 Amps To 32 Amps Rating, 240/415 Volts, C Curve, Miniature Circuit Breaker Suitable For Inductiveof Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. Iii. Triple Pole , S/F Sp Mcb Db: Supplying And Fixing Following Way, Prewired, Spn Mcb Distribution Board Of Steel Sheet For 240 Volts, On Surface/Recess, Complete With Losses Wire Box, Terminal Connectors For All Incoming And Out Go Circuits, Duly Prewired With Suitable Size Frls Pvc Insulated Copper Conductor Up To Terminal Blocks Tinned Bus Bar, Neutral Link, Earth Bar, Din Bar, Detachable Gland Plate, Interconnection Powder Painted Including Earthing Etc. As Required. I. 2 + 8 Way Double Door , Supply And Fixing Of Led Cove Light (Rope Type ) Make Philips/ Havells /Acco Or Equivalent, Ofwarm White6watt/ Meter , 3000K Ip65 400 Lumens /Meterof With Adaptor As Per The Site Requirement. , Supply And Fixing Of Led Recessed Light Make Philips/ Havells /Acco Or Equivalent,36Watt 2Ftx2ft With All Necessary Fittings Required , Furniture , Supply And Fixing Of Modular Workstation Of Size 1050W X 600D X 750/1050 H Mm With Provision Of Cpu Rack And Keyboard Table Top With Grommet:- 25Mm Thick Plpb Board With 2Mm Thick Pvc Edge Banding Finish With As Per Approved Laminate Color. Legs:-Aluminium 60Mm X 30Mm Triangular Leg With Powder Coated Finish As Per Approved Shade. Beam: - 40Mm X 40Mm Crc Square Pipe With Powder Coated Finish As Per Approved Shade Provided With Die Casted Brackets To Support Top. Wire Carrier: - Powder Coated Wire Carrier To Be Provided For Arranging Wires For Electricity & Data. Riser Leg:- Powder Coated Wire Riser To Be Provided For Raising Wires Form Floor . Passage Side Modesty (450Ht):- Metal Powder Coated Modesty Finish With As Per Approved Shade. , Supply And Fixing Of Modular Pedestal Storage Of Size - 400 W X 450 D X 575 H Mm Mobile Drawer (2Dr+1F):- 18Mm Thick Plpb Board With 2Mm Thick Pvc-Edge Banding Finish With As Per Approved Laminate Color. , Supply Of Medium Back Executive Chairs , Supply Of Fully Leatherier Sofa Seat Of The Best Quality As Per Approved Design (2 And 3 Seater) As Per Approved Design. , B. Group B , Extended 2 Year Onsite Oem Warranty/Amc After Completed 5 Year Warranty Of Complete System
