Tender For Special Repair Work Of Electrical Work At Esic Bo And Esi Dispensary Rourkela, 1 Wiring Work 2 Wiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVC insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable GI box and earthing thepoint with 1.5 sq.mm FRLS PVC insulated copper conductorsingle core cable etc. as required. 3 Group A 4 Group B 5 Group C 6 Rewiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVC insulated copper conductorsingle core cable and 1.5 sq.mm FRLS PVC insulated copperconductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required. 7 Group A 8 Group B 9 Group C 10 Wiring for twin control light point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface /recessed steel conduit, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVCinsulated copper conductor single core cable etc. as required. 11 Wiring for light/ power plug with 2X4 sq. mm FRLS PVCinsulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mmFRLS PVC insulated copper conductor single core cable for loopearthing as required. 12 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired. 13 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 14 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 15 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 16 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 17 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 18 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mmsolid copper conductor PE insulated, shielded with fine tinnedcopper braid and protected with PVC sheath in the existingsurface/ recessed steel/ PVC conduit as required. 19 Supplying and fixing of following sizes of medium class PVCconduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessedconduit as required. 20 25 mm 21 40 mm 22 Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required. 23 5/6 A switch 24 2 way 5/6 A switch 25 15/16 A switch 26 3 pin 5/6 A socket outlet 27 6 pin 15/16 A socket outlet 28 TV antenna socket outlet 29 Bell push 30 Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required. 31 Supplying and fixing modular blanking plate on the existingmodular plate & switch box excluding modular plate asrequired. 32 Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required. 33 1 or 2 Module (75mmX75mm) 34 3 Module (100mmX75mm) 35 6 Module (200mmX75mm) 36 8 Module (125mmX125mm) 37 12 Module (200mmX150mm) 38 Supplying and fixing 3 pin, 5 A ceiling rose on the existingjunction box/ wooden block including connections etc. asrequired. 39 Installation, testing and commissioning of ceiling fan, includingwiring the down rods of standard length (upto 30 cm) with 1.5sq. mm FRLS PVC insulated, copper conductor, single core cable,including providing and fixing phenolic laminated sheet coveron the fan box etc. as required. 40 Installation of exhaust fan in the existing opening, includingmaking good the damage, connection, testing, commissioningetc. as required.Upto 450 mm sweep 41 Extra for fixing the louvers/ shutters complete with frame for aexhaust fan of all sizes. 42 Supplying and fixing PVC batten/ angle holder includingconnections etc. as required. 43 DB PANEL/MCB PANEL/ LT Panel Work 44 Providing and fixing following rating and breaking capacity andpole MCCB with thermomagnetic release and terminalspreaders in existing cubicle panel board including drilling holesin cubicle panel, making connections, etc. as required. 100 A,30KA,FPMCCB 45 Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator) 46 8 way , Double door 47 12 way , Double door 48 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, Ccurve, miniature circuit breaker suitable for inductive load offollowing poles in the existing MCB DB complete withconnections, testing and commissioning etc. as required. 49 Single pole 50 Double pole 51 Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required. 63 A 52 Supplying and fixing following rating, four pole, 415 V, isolatorin the existing MCB DB complete with connections, testing andcommissioning etc. as required. 63 A 53 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. asrequired. 63 A 54 Supplying and fixing single pole blanking plate in the existingMCB DB complete etc. as required. 55 Supplying and fixing TP sheet steel enclosure on surface/ recessalong with 16/25/32 A 415 V C curve TP MCB complete withconnections, testing and commissioning etc. as required. 56 Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreousenameled white on both sides, and with inscription in single redcolour on front side as required. 57 Supplying and fixing Cable End Box (Loose Wire Box) suitable forfollowing single pole and neutral, sheet steel, MCB distributionboard, 240 Volts, on surface/ recess, complete with testing andcommissioning etc. as required. 58 For 8 way, Double door SPN MCBDB 59 For 14 way, Double door SPN MCBDB 60 Supplying, installing on wall, testing and commissioning offollowing capacity rising mains made of 1.6mm thick IP 42 sheetsteel enclosure duly painted with powder coating, wall straps,fully PVC insulated 4 Nos aluminium bus bars having currentdensity of 130 A/ sq cm at nominal current rating inconvenient sections and suitable for 415 V, 3 phase, 4 wire, 50Hz, A.C. supply with extension joints, fire proof barriers,expansion joints, thrust pads including jointing and earthingwith 2 runs of galvanised iron strips etc. as required. (Risingmains confirming to IS 8623, TEC 439) 200 A (S.C. rating for 1 sec - 15 kA) 61 Supplying and installing following size of perforated HotDipped Galvanised Iron cable tray (Galvanisation thickness notless than 50 microns) with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required. 62 225 mm width X 50 mm depth X 1.6 mm thickness 63 300 mm width X 50 mm depth X 1.6 mm thickness 64 450 mm width X 50 mm depth X 2.0 mm thickness 65 Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray bends (galvanisation not less than50 microns) with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required. 66 225 mm width X 50 mm depth X 1.6 mm thickness 67 300 mm width X 50 mm depth X 1.6 mm thickness 68 450 mm width X 50 mm depth X 2.0 mm thickness 69 Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray Tee (galvanisation not less than 50microns) with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceilingwith G.I. suspenders including G.I. bolts & nuts, etc. as required. 70 225 mm width X 50 mm depth X 1.6 mm thickness 71 300 mm width X 50 mm depth X 1.6 mm thickness 72 450 mm width X 50 mm depth X 1.6 mm thickness 73 Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray Cross member(galvanisation notless than 50 microns) with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etcas required. 74 225 mm width X 50 mm depth X 1.6 mm thickness 75 300 mm width X 50 mm depth X 1.6 mm thickness 76 450 mm width X 50 mm depth X 1.6 mm thickness 77 Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray Reducer (galvanisation not lessthan 50 microns) with perforation not more than17.5%, inconvenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etcas required. 78 225 mm width X 50 mm depth X 1.6 mm thickness 79 300 mm width X 50 mm depth X 1.6 mm thickness 80 450 mm width X 50 mm depth X 1.6 mm thickness 81 Earthing and Lightining Arrester 82 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required. 83 Earthing with copper earth plate 600 mm X 600 mm X 3 mmthick including accessories, and providing masonry enclosurewith cover plate having locking arrangement and watering pipeof 2.7 metre long etc. with charcoal/ coke and salt as required. 84 Supplying and laying 6 SWG G.I. wire at 0.50 metre belowground level for conductor earth electrode, includingconnection/ termination with GI thimble etc. as required. 85 Providing and fixing 4.00 mm dia copper wire on surface or inrecess for loop earthing as required. 86 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 87 Fixing of lightning conductor finial (single prong) with base plateincluding holes etc. complete as required. 88 Jointing copper / G.I. tape (with another copper/ G I tape, baseof the finial or any other metallic object) by riveting / nutbolting/ sweating and soldering etc as required. 89 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet orsurface of wall for lightning conductor complete asrequired.(For horizontal run) 90 Providing and laying G.I. tape 32 mm X 6 mm from earthelectrode directly in ground as required. 91 LT Cable Laying work 92 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 93 Above 35 sq. mm and upto 95 sq. mm 94 Above 95 sq. mm and upto 185 sq. mm 95 Laying and fixing of one number PVC insulated and PVCsheathed / XLPE power cable of 1.1 KV grade of following sizeon cable tray as required. 96 Upto 35 sq. mm (clamped with 1mm thick saddle) 97 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mmMS flat clamp) 98 Supplying and making end termination with brass compressiongland and aluminium lugs for following size of PVC insulatedand PVC sheathed / XLPE aluminium conductor cable of 1.1 KVgrade as required. 99 3½ X 25 sq. mm (28mm) 100 3½ X 35 sq. mm (32mm) 101 3½ X 70 sq. mm (38mm) 102 Supplying and making straight through joint with heatshrinkable kit including ferrules and other jointing materials forfollowing size of PVC insulated and PVC sheathed / XLPEaluminium conductor cable of 1.1 KV grade as required. 103 3½ X 25 sq. mm 104 3½ X 35 sq. mm 105 3½ X 70 sq. mm 106 Providing, laying and fixing following dia G.I. pipe (mediumclass) in ground complete with G.I. fittings including trenching(75 cm deep)and re-filling etc as required 107 50 mm dia 108 100 mm dia 109 Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required. 110 BLDC FAN 111 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 112 LAN Cable and Networking 113 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in theexisting surface/ recessed Steel/ PVC conduit as required. 1 run of cable 114 Supplying and fixing following size/ modules, Gl box alongwithmodular base & cover plate for modular switches in recess etc. asrequired.1 or 2 Module (75mmX75mm) 115 CCTV Camera 116 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in theexisting surface/ recessed Steel/ PVC conduit as required. 1 run of cable 117 Auto Control Panel for Light 118 Supplying,installation,testing and commissioning ofAstronomical time switch of following configuration to bemounted in feeder pillars / Lighting DBs for automaticswitching On & OFF of street lights at sun set & sun rise ortwilight(Auto ON, Auto OFF, Auto modes) with manual overridefacility with 12/24 hour display format with suitable battery andindication for relay status i/c programming at site complete asrequired.2 output per phase and suitable for single phase supply 119 Add GST Factor @ 1.0633 for GST 18%, Then Total 120 Providing & Fixing 36 Watts Heavy Duty Polycarbonate 600 X 600 (2X2) Square LED Panel Light (Pack of 1, Cool Day Light) Recessed Ceiling Lamp (White) 121 Wooden screw 122 PVC slip 123 pvc Tape 124 Supply and installation of Wire Less Calling Bell complete work in all respect 125 Supply and Installation of 20 watt LED Square Light complete work in all respect. 126 Flexible Pipe 25mm 127 Flexible pipe 50mm 128 Cable Tie 129 Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV GSolid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1)1988 armoured U.G. cableU.G. cable laid in ground/partially in air (as required for termination over groundincluding excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris etto proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 3 & 1/2 Core A2XFY 130 10.00 Sq.mm.3 Core armoured U.G. cable 131 35.00 Sq.mm.3 & 1/2 Core armoured U.G. cable 132 70.00 Sq.mm.3 & 1/2 Core armoured U.G. cable 133 Supplying including fitting fixing of followingA.C. Exhuast fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Crisp Air with louver 250 mm sweep 134 Supplying including fitting fixing of followingA.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Swing platinawith plastic blade, 400 mm sweep 135 supply and Installation of 18 w LED Bulb in existing holder in complete work in all respect. 136 Supply and Installation of 12 watt LED Bulb complete work in all respect. 137 Supplying with installation testing and commissioning of Hi -- wall 5 STAR rating non ducted split typeair conditioner of the following capacity with cordless remote complete with copper pipeand electrical connection cable,as approved by the Deptt.)up to 5 m between the room unit and out door unit as directed by the department.2 Ton 138 Supplying with fitting and fixing Single Phase D.O.L Starter of the following specification complete including making necessary connection as approved, specified and directed by the deptt. Overload Relay Range 3.8 - 6.0 Amps for 2.2 KW 139 LAN Cabling/Networking Item 140 Patch Panel Cat 6 UTP Keystone -24 Port- Loaded SCHNEIDER/LEGRAND or equivalentmake as approved by the Deptt. 141 Patch Cord Cat 6 UTPGray 1m - Moulded SCHNEIDER/ LEGRAND or equivalent as per direction of dept. 142 Patch Cord Cat 6 UTPGray 2m - Moulded SCHNEIDER/ LEGRAND or equivalent as per direction of dept. 143 Cat 6 KeystoneUTP Jackwith Dust Cover-WhiteSCHNEIDER/LEGRAND or equivalentmake as approved by the Deptt.. 144 DIGILINKL/ LEGRAND OR equivalent 24 Port 10/100/1000Mbps Layer 2 stackable Switch with 4 Gigabit Combo Ports 145 9U Rack Loaded SCHNEIDER/ LEGRAND or equivalent 146 CCTV 147 SITC of 4 MP Bullet CCTV Camera having specification of Image Sensor type-CMOS, Camera Image Sensing capacity (Picture Mode)-4 MP, Resolution- D1(704X480 Pixel), HD (1280X720 Pixel), Full HD (1920X1080 Pixel), CIF, D1, 1080P (1920X1080), 1920X1080 (30 fps), 720P (1280X720), Day/Night Capable -Yes, IR illumination Range (mtr)-45, Camera Type - BULLET TYPE, IP Camera – Yes, Digital zoom -16X, Audio support- Yes, Alaram Support- Yes, Multilevel user ID/Password- Yes, IP Address Filtering- Yes, White Balance, Auto Gain Control, Back Light Compensation, Remote administration, Remote System update over network, PC Client, Web Client, On Screen Display in english, ONVIF Support, - Yes, Supported Protocol - UDP, IGMP, DHCP, RTP, HTTP, SMTP, FTP, ICMP, HTTPS, DNS, DDNS, RSTP, RTCP, NTP, QoS, TCP/IP, PPPoE, 802.1X, Installation type- Indoor, Outdoor etc as per direction of Engineer. 148 SITC of 4 MP Dome CCTV Camera having specification of Image Sensor type-CMOS, Camera Image Sensing capacity (Picture Mode)-4 MP, Resolution- D1(704X480 Pixel), HD (1280X720 Pixel), Full HD (1920X1080 Pixel), CIF, D1, 1080P (1920X1080), 1920X1080 (30 fps), 720P (1280X720), Day/Night Capable -Yes, IR illumination Range (mtr)-45, Camera Type - Dome TYPE, IP Camera – Yes, Digital zoom -16X, Audio support- Yes, Alaram Support- Yes, Multilevel user ID/Password- Yes, IP Address Filtering- Yes, White Balance, Auto Gain Control, Back Light Compensation, Remote administration, Remote System update over network, PC Client, Web Client, On Screen Display in english, ONVIF Support, - Yes, Supported Protocol - UDP, IGMP, DHCP, RTP, HTTP, SMTP, FTP, ICMP, HTTPS, DNS, DDNS, RSTP, RTCP, NTP, QoS, TCP/IP, PPPoE, 802.1X, Installation type- Indoor, Outdoor etc as per direction of Engineer. 149 Processor-Embedded processorOperating System -Embedded LINUXIP Camera Input-8: each channel up to 4MPTwo-way Talk-Reuse audio in/out, RCAUser Interface-GUIVideo Output-1 HDMI, 1 VGAVideo Resolution-HDMI: 1920 x 1080, 1280 x 1024, 1280 x 720 VGA: 1920 x 1080, 1280 x 1024, 1280 x 720Video Recording Main stream-All channel 5M-N(1fps–10fps); 4M-N/1080p (1 fps–15 fps); 720P/960H/D1/CIF (1 fps–25/30 fps); Sub stream: 960H (1 fps–15 fps); 1/CIF (1 fps–25/30 fps)Resolution-5MP, 4MP, 3MP, 1080P, 720P, 960H, D1, CIF, BCIF, QCIFVideo Compression-H.264+/H.264Video Display Split-1/4/8/9/16Video Channel-16 channels, BNCAnomaly Alarm-No disk, disk error, low space, offline, IP conflict, MAC conflictAlarm Linkage-Record, snapshot (panoramic), IPC external alarm output, access controller, voice prompt, buzzer, log, preset, email General Alarm, Motion detection, Video Loss, tampering With 4 TB Harddisk Drive 150 Supplying installation testing and commissioning of 16 port L2 PoE Switch 151 Supply and installation of 32’ LED full HD (1920x1080) Resolution Android Smart TV having Brightness 450 nits minimum, IPS technology, no of speaker 2 with minimum 20 watt, output port for audio, HDMI Port, DVI-D Port, Display Port, USB Port, RS 232C Port, RJ45 Port, power supply 220-240 V AC 50 Hz, Operating temp 0-40 Degree C, with installation Accessories like wall mount bracket, remote, power cord, and other accessories. Complete as per direction of ESIC engineer. Make -LG, Sony and Panasonic, Motorola. 152 SITC of 6 mtr Hotgalvanised octagonal GI Tubulor pole inlcuding GI single ARM bracket/ Double ARM bracket inlcuding junction Box and Base plate with Nut and bolt.foundation work inluding with this scope of work as per direction of Engineer. 153 Supply with fitting & fixing of 12 mtr height Six arm high mast GI tubular Pole. The pole is made of GI tube ,integral with built in cylindrical GI control box, service door and a circular base plate . The pole is swaged at the top to accommodate the bracket assembly secured on to the top by means of 2 annular rings with Allen grub screws . The pole and the bracket are coated with epoxyzinc phosphate primer and finished with polyurethane based paint . The control gear tray is pre-cabled with MCB, terminal connection as approved by the Deptt.)for loop in loop out and suitable for LED Flood lamp for operation on 240 V, 50 HZ single phase AC Supply .The pole is to be fitted on 1:3:6 PCC pole foundation of size 300 mmx300 mmx1200 mm with grouting nuts & bolts as specified & directed by the deptt, For fiiting of Light in pole through chain and rope items shall be including with this cost. 154 Supplying with fitting & fixing of the following street light completein the existing pole with high power LED and extendable up to with unique peanut lens to ensure uniform distribution including making necessaryconnection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. 70 watt with Water Rasistant IP66. 155 Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical typecompartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coatsof enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. Supplying with fitting & fixing of the following capacity flood light completein the existing pole with high power LED and extendable up to with unique peanut lens to ensure uniform distribution including making necessaryconnection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. 150 watt with IP66 156 Supply,installation and testing, fiitingof Glow Sign Board of 7x3 Feet for BO and Dispensary location with making Iron Frame complete work as per direction of ESIC Engineer 157 Supply,installation and testing, fiitingof Glow Sign Board of 15x3.5 Feet for BO and Dispensary location with making Iron Frame complete work as per direction of ESIC Engineer 158 Less GST
