Tender for civil construction work of Material Recovery Facility (MRF) in village Rampur Japati Pargana Nizamabad Tehsil Sadar District Azamgarh, 1 Earth Work in Excavation for structure as per drawing and technical specification clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal up to a lead of 50m. Dressing of sides and bottom and backfilling in trenches with excavated suitable Material. Ch. No. 4, S.I. No. 2 2 Carted earth filling in Foundation up to Plinth Level including ramming and dressing the surface to the required levels and lead up to 8 km from suitable approved borrow pit work complete as per direction of E/I. 3 Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & floors. 4 Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 kms. from the site of work and including watering, dressing etc rate to include cost of all materials labour T & P etc required for proper completion of work. 5 Providing and injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete.(plinth area of the building at ground floor only shall be measured as per I.S.6313 (PartII 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows : (1) Treatment for masonary & foundation 5 liters per sqm. (2) Back fill in immediate contact with foundation 7.5 liters/sqm (3) Treatment of top surface of plinth filling 5 liters/sqm (4) Treatment junction of wall and the floor 7.5 liters /sqm (5) Treatment of soil along external perimeter of building 7.5 liters/sqm (6) Treatment of soil under apron along external perimter 5 liters/sqm. (As per manufacturers standard dilution) 6 R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. including cost of binding wire. The rate excludes making of drip course which shall be paid extra.As in item 6 abovebut inR.C.C.Raft foundation and footingwithapproved stone ballast.(Using1:1.5:3Mix concrete) 7 As in item 6 but for thelighterbeams i.e. having spans upto 6 m. (Using 1:1.5:3 Mix concrete) 8 As in item 6 above but in R.C.C. columns in 1:1.5:3 having strength not less than M-20. 9 M-150 brick work in 1:6 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. 10 Same as in item No. 11 abovebutin super-structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honeycombed brick work in thickness of wall more than 12cms. (1:6 cement : coarse sand) 11 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 12 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 fine sand 13 15mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 fine sand 14 40 mm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 20 mm graded approved stone laid in panels finished with 3 mm flooring coat of neat cement or cement and marble dust in 5:1 as specified over & including 75 mm thick base concrete consisting of cement, local sand and brick balast 40 mm gauge in the proportion of 1:4:8 and removing any over lapping morter at joint of pannels if any and giving them a uniform finish including supply of all materials, labour and T&P etc. required for proper completion of the work. as per sand fo 1.25FM. (As per PWD. S.I. No 604a) 15 P/F of Glass strip 5 mm thick 35 mm wide 16 Steel work in builtup tubelar ( round squre or rectangular hollow tubes etc) truss etc including cutting costing fixxing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc complete electric resistance or induction nutt welded. 17 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheetscomplete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m² 18 Painting or vanishing on iron on iron works in small areas or new wood with one coat of ready mixed priming paint and one coat of approved superior ready mixed paint of clear syuthetic varnish including supply of all materials, labour and T&P etc. required for proper completion of the work.Paint to used should confirm to the ISI No.1031950. (As per PWD. S.I. No 641+642) FOR STEEL SURFACES 19 Painting or vanishing on iron on iron works in small areas or new wood with one coat of ready mixed priming paint and one coat of approved superior ready mixed paint of clear syuthetic varnish including supply of all materials, labour and T&P etc. required for proper completion of the work.Paint to used should confirm to the ISI No.1031950. (As per PWD. S.I. No 641+642) FOR WOODEN SURFACE 20 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. 21 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction ofEngineer-in-charge.Made of G.I. wire of dia 4 mm 22 M.S. or Iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. Providing & fixing of hold fast for chaukhatsof doors and windows. 23 Providing & fixing of HOLDFAST door / windows grill. 24 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws 25 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 26 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete (a) 250 mm x 10mm 27 Providing and fixing stainless steel handles with screws etc. complete (a) 125 mm 28 Finishing walls with water proof cement paint of approved make and quality on new work with three coats to give an even shade.Incl. supply of all material,labour and T & P etc required for proper completion of work(SOR-660+661) 29 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 30 ADD INTERNAL ELECTRIFICATION WORK AS PER DETAILS ATTACHED SHEET 31 ADD EXTRA FOR 6 WATER TAPS IN WASHING UNIT 32 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 33 Supply of 80mm thick I Shapped mechanically interlocking cement concrete pavers block manufactured by high pressure & controlled vibration machine having plan dimension 200x(160+120mm) with minimum 5mm thick topping of O.P. cement mixed with 25% marble powderthe compressive strength of concrete pavor block shall not be less than 30 PMa and 4.50 Kg./No. including cost of all materials, labour T&P etc. required for proper completion of the work as per Directed by Engineer-In-Charge. 34 Making grooves 10 to 12 X 12mm and upto 25 X 15 mm deep in plaster of the walls or in ceiling vertically or horizontally as required. 35 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 36 Providing and laying Ceramic glazed WALLtiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 37 25 mm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 20 mm graded approved stone laid in panels finished of all materials, labour and T&P etc. required for proper completion of the work. as per sand fo 1.25FM. (As per PWD. S.I. No 604a) 38 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 39 M.S. or Iron work of small sizes and sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work.FIXXING OF DOOR &WINDOW GRILL,Z- SECTION OF STEEL WINDOW& ANGLE ,angle iron door chaukhat 40x40x6 40 Fixxing of door & window ventilator chaukhat in position. door chaukhat 41 ventilators chaukhat 42 Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Internal wall surface) 43 Finishing walls with acrylic smoth exterior paint of approved make and quality on new work with three coats to give an even shade.Incl. supply of all material,labour and T & P etc required for proper completion of work(SOR-660+661) 44 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 45 Providing and fixing stainless steel door stopper with necessary screws etc. complete 46 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: above operations to be done in order and as directed and pecified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 47 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes 48 INTERNAL W/S AND SANITATION 49 SOAK PIT 50 M.S. or Iron work of small sizes andHEAVY sections such as holding down bolts, hold fast tie rods, gratings etc. wrought to required from including supply of steel bolts, nuts wastage etc and fixing required for proper completion of the work. 51 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road rollerincluding making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 52 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motorgrader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. 53 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewateringprocess and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately).(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 54 Boring with 2 HP 9 stage submerssible pump of ISI maraka with automatric panel includding supply of all accessories starter panel & pipe arrengement etc complete.
