|
| 1 | Sch \"A\" Part-I (B/R works) Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster and demolition of cement concrete etc and cleaning the surface with wire brush including removing debris from the site and depositing inlow lying area where directed and providing following :- (a)Rendering 10mm thick in Cement mortar (1:3)on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing liquidwater proofing compound @ 200ml per 50 Kg bag of cement.(b)Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried.(c)Provide 3mm thick APP modified prefabricated polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3.5 Kg per sqm. APP membrane shall laid acorss the slope from lowest line of sloping roof towards ridge.(d) Finishing with aluminium paint applied @ 0.11 Kg/sqm over the APP.Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed by Engr-In-Charge.(iii)Liquid water proofing compound shall be measured and paid for separately. |
| 2 | M&L for 25mm thick PCC 1:2:4 type B-0 (using 20 mm graded stone aggregate) to make up undulationsas in levelling course/roof padding over roof slab, projections on similar surfaces existing with slope, making the surface even smooth without using extra cement complete all as specified and directed. . |
| 3 | Supply only liquid water proofing compound |
| 4 | Taking down cement plaster, any description on brick or stone or cement concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 5 | M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick, stone or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. |
| 6 | M&L for 20 mm thick renderingin cement mortar (1:4) in two layers (12 mm +8 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved Liquid WPC on second layer (8 mm) as per manufacturer instruction complete all as specified and directed.(Note: Liquid WPC shall be measured and paid separately as supply only.) |
| 7 | M&L for 5 mm thick renderingin cement mortar (1:3) on ceiling surfaces, finished the surfaces even and smooth without using extra cement complete all as specified and directed |
| 8 | M&L for complete removal of existing treatment on walls by washing down and smoothing old surface and applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint as per manufacturer instruction with smooth roller finish complete all as specified and directed by Engineer-in-Charge.(Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 9 | M&L for complete removal of existing treatment on ceiling by washing down and smoothing old surface and applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint as per manufacturer instruction with smooth roller finish complete all as specified and directed by Engineer-in-Charge.(Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 10 | M&L for applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint as per manufacturer instruction after preparation of new plaster surfaces of wall complete all as specified and directed by Engineer-in-Charge.(Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 11 | M&L for applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint as per manufacturer instruction after preparation of new plaster surfaces of ceiling complete all as specified and directed by Engineer-in-Charge.(Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement) |
| 12 | M&L for complete removal of existing treatment of walls by scrapping down with mechanical wall sandar (having mechanical vaccum mechanism) from old plastered surfaces on ceiling and applying two coats of weather proof exterior emulsion (Anti fungal paint) over a coat of primer complete all as specified and directed. |
| 13 | M&L for applying two coats of weather proof exterior emulsion (Anti fungal paint) over a coat of primer including preparartion ofnew plastered surfaces of walls complete all as specified and directed. |
| 14 | Demolition of cement concrete unreinforced in ground floor & paving n exc 15cm thickness (below or above GL)and removal of debris from site complete all as specified and directed. |
| 15 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed. |
| 16 | M&L for glazedceramic coloured tiles of size 450x350x7mm/ 600 x 300 x 7mm (premium quality) on vertical surface such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick screed bed in cement mortar (1:3) after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and as directed. |
| 17 | M&L for non skid ceramic colour tiles 7 to 8 mm thick (premium quality), area of each tilesn exc 0.36 sqm as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 10 mm thick screed bed in cement mortar (1:4) complete all as specified and directed. |
| 18 | Taking down chowkhats or frames(without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed. |
| 19 | Taking down chowkhats or frames with shutter (without taking off shutter from the frame)exc 1.5 Sqmand n.exc 4 Sqm each and removing to store complete all as specified and directed. |
| 20 | Taking down shutters of any description areaexc 1 sqm and n.exc 2 sqm each complete all as specified and directed. |
| 21 | S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS squarecomplete all as specified and directed. |
| 22 | S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR complete all as specified and directed. |
| 23 | S&F for pressed steel door frame of size 165x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats, fixing holdfast, in bands etc. in PCC (1:3:6) type C-0,(using 12.5mm graded stone agregate) including necessary formwork complete all as specified and directed. |
| 24 | S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I) kiln seasoned and chemically pressure treatedcomplete all as specified and directed. |
| 25 | S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (with sash bars, any numbers) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkhats complete all as specified and directed. |
| 26 | S & F for 250 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed |
| 27 | S & F for 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 28 | S & F for 150 mm long aluminium alloy handles, cast type, anodized complete all as specified and directed. |
| 29 | S&F for 100 mm long Butt hinges (medium weight) stainless steel complete all as specified and directed. |
| 30 | S&F for 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floorcomplete all as specified and directed. |
| 31 | M & L for PCC (1:3:6) type C1 (using 20 mm stone aggregates) as in hold fast block including necessary form work etc. complete all as specified and directed. |
| 32 | M&L for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate welded to steel frame complete all as specified and directed. |
| 33 | S&F for cutain rails, mild steel, chromium plated with fixing brackets, stops, tollers etc. including side caps and bracketscomplete as in repair all as specified and directed. |
| 34 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wood and wood based surface over 10 cm width or girth not otherwise described including preparation complete all as specified and directed. |
| 35 | M&L for applying two coats of synthetic enamel paint on old wood and wood based surface over 10 cm width or girth not otherwise described including preparation complete all as specified and directed. |
| 36 | M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 37 | M&L for preparation of old painted steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of Synthetic enamel paint complete all as specified and directed. |
| 38 | S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4mm and fixed with tinned tacks, or stainless steel wire staples in steel windows/ wooden doors complete all as specified and directed. |
| 39 | S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4mm and fixed with tinned tacks, or stainless steel wire staples in steel windows/ wooden doors complete as in repairall as specified and directed. |
| 40 | S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 41 | S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed. |
| 42 | S&F for guard bars to windws, plain, let in and fixed independently in steel frames including welding etc guard bars and similars work conforming to Fe-290 Grade E-165 complete all as specified and directed. |
| 43 | S&F for Powder coated anodised aluminium ventilator frame (louvered type) without sash bars, aluminium sections weighing not less than 0.55 kg/m including all fittings and necessary locking arrangements. The vetilator system should be glazed with 4mm thick figured glass, pin head type of size as required in ventilator frame (louvered type) as per manufacturer instruction including taking out/ taking down old ventilator complete all as specifed and directed. |
| 44 | S&F for 3 mm thick sheet glass ordinary quality and glazing with oil putty/beads and pins/spring pins in squares n . exc 0.50 sqm in each paneto be fixed in any position at any hight upto to two story building complete all as specified and directed. |
| 45 | S&F for 3 mm thick figured glass pin headed type and glazing with oil putty/beads and pins/spring pins in squares n . exc 0.50 sqm in each paneto be fixed in any position at any hight upto to two story building complete all as specified and directed. |
| 46 | Hacking out broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old galzing pins/ spring clips complete all as specified and directed. |
| 47 | S&F forviterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, fixing bolts and flushing pipe (excluding flushing cistern ) completeas in repair all as specified and directed. |
| 48 | S&F for vitreous China water closet (squatt pan) Orrisa pattern 580x440 mm size pan, white, withfront or back inlet with integral \"foot rests including provn of lime concrete bedding including connections to flushing cistern/pipe and flush pipe of 32 mm dia (PVC) as in repair complete all as specified and directed. |
| 49 | S&F forPVC low level flushing cistern 10 ltrs capacity white with inlet ball valve, float valve and handle including providing & fixing MS angle iron brackets, PVC flush pipe of 32 mm dia complete as in repair all as specified and as directed. |
| 50 | S&F for 15 mm bore Bib taps 2 way fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified. (MakeJaquar Cat No KUP-35041PM or equivalent of Parryware/ Kohler/ Marc as approved by GE.) |
| 51 | S&F for CP brass health faucet of 8mm dia, with 1.2 mtr long flexible tube and wall hook with back flow preventer including all fittings complete as in repairs all as specified and directed. (MakeJaquar Cat No ALD-577 or equivalent of Parryware/ Kohler/Marc as approved by GE) |
| 52 | S&F for toilet paper holder (CP) fancy type complete as in repair all as specified and directed.(Make:- Jaquar Cat No ACN-1155S or equivalent of Parryware/ Kohler/Marc as approved by GE) |
| 53 | S&F forvitreous China wash basin, white, flat back, size 550x 400mm including brackets (2 nos), 15mm bore pillar tap cast copper alloy with capstan head (CP), waste coupling (CP), short piece connection as required length, CP waste pipe 32mm dia complete as in repair all as specified and directed. |
| 54 | S&F for 15mm bore pillar tap fancy type cast copper alloy with capstan heads chromium plated screwed down or high pressure with or without lettered hot or cold with long screwed shank and fly nuts for iron pipe fixedcomplete as in repair all as specified and directed.(Make:- Jaquar Cat No CON-117BKN or equivalent of Parryware/ Kohler/Marc as approved by GE) |
| 55 | S&F for vitreous China urinal, half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long bras screws, pointing around urinal back in cement; including flush pipe, grating and union for discharge pipe, complete as in repair all as specified and directed. (Make:- Hindware/ Johnson/ Parryware/ Cera) |
| 56 | S&F for cast copper alloys chromium plated fancy type urinal spreader with auto closing system push cock (Urinal valve) with chromium plated hose pipe fixed suitable for 15mm dia pipe for urinals complete as in repair all as specified and directed. (Make:- Hindware/ Johnson/ Parryware/ Cera) |
| 57 | S&F for vitreous china urinal partion white of size 310mm x 700mm complete as in repair all as specified and directed. (Make:- Hindware/ Johnson/ Parryware/ Cera) |
| 58 | S&F for PVC connection 15 mm dia withPTMT nuts of length 450mm at both ends screwed for iron pipe of 15 mm bore complete as in repair all as specified and directed. |
| 59 | S&F for brass chromium plated wall mixer , 3 in 1 for system with provision for overhead shower complete with 115 mm long bend pipe, connecting legs & wall flange (without overhead shower) complete as in repair all as specifiedand directed.(Make:- Jaquar Cat No CON-273KNUPR or equivalent of Parryware/ Kohler/Marc as approved by GE) |
| 60 | S &F for overhead shower rose 200mm x 200mm square single flow with shower arm square 450mm long complete as in repair all as specified and directed.(Make:- Jaquar/ Parryware/ Kohler/Marc) |
| 61 | S&F for soap dish including chromium plated brass screws and wooden plastic cleats complete as in repair all as specified and directed. |
| 62 | S&F for Brass chromium plated tubular towel rail 20 mm dia \"D\" type 60 cm long between flange aluminium anodised complete all as specifed and directed. |
| 63 | S&F for 600x450mm bevelled edge mirror of selected quality glass,mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer complete as in repair all as specified and directed. |
| 64 | M&L for 15mm diabib tap cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwedfor iron pipe complete as in repair all as specified and directed. |
| 65 | S&F for 15 mm dia angular stop cock with flange chromium plated fancy type complete as in repair all as specified and directed.(Make:- Jaquar Cat No KUP-35053PM or equivalent of Parryware/ Kohler/Marc as approved by GE) |
| 66 | M&L for 75mm bore PVC (SWR) floor/Nahani trap, plain with grating including jointing with solvent cement including fixing in cement concrete (1:2:4) type B-1 complete as in reapir all as specified and directed. |
| 67 | S&F for Grating doom 125 mm of PTMT (Min Weight 40 Gms) with waste hole complete as in repair all as specifed and directed. |
| 68 | S&F for 15 mm bore galvanised iron GI tubing (medium grade) with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete after taking down old unserveciable 15mm dia GI pipe with fittings all as specified and directed. |
| 69 | S&F for 20 mm bore galvanised iron GI tubing (medium grade) with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete after taking down old unserveciable 20mm dia GI pipe with fittings all as specified and directed. |
| 70 | S&F for Rotational moulded polythylene water storage tank (ISI marked multilayer) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs includingdismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball valve (minimum weigth of valve 210 gms) high pressure of PTMT with epoxy coated aluminium rod and high density plasic ball screwed for iron pipe and fixedcomplete all as specifed and directed. |
| 71 | M&L for 75mm thick PCC type C-2 (1:3:6), (using 40 mm graded stone aggregates) as in plinth protection, pavement etc. and finshed the surface even and smooth without using extra cement after demolition of cement concrete of any description in any position complete all as specified and directed. |
| 72 | M&L for chequered cement concrete tiles of size 30 cm x 30cmx22 mm thick set, jointed in neat cement slurry in floor and pointed in white or grey cement and no pigment of machine pressed to match the shade of tiles laid over and including 15 mm thick screed bed in cement mortar (1:6) and also including over 75mm thickPCC 1:3:6, type C-2 (using 40mm graded stone aggregates) as in sub base to receive tiles after demolition/dismantling of existing unserviceable cement concrete tiles complete all as specified and as directed. |
| 73 | Demolition of reinforced cement concrete of any description and in anypositionnot otherwise specifically provided for complete all as specified and directed. |
| 74 | M & L for formwork for flats, rough finished concrete surfaces for chullah hoods, chajjas,troughs and similar items including edges complete all as specified & directed |
| 75 | Supplying fabricating and placing in position of new TMT bars of any dia suitable at site by welding or inserting by drilling hole and embedded in epoxy grout bounding agent of hilti or equivalent for all existing reinforcement repair works in any position wherever necessary complete all as specified and directed.(Note:- The lap provided shall be minimum 15 cm on either side of bar which has lost its sectional area.) |
| 76 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 77 | M&L for reinforced cement concrete 1:2:4 (nominal mix) type B1 using 20 mm crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.(Note:-Reinforcement and form work shall be measured and paid separately.) |
| 78 | M&L for reinforced cement concrete 1:1.5:3 (nominal mix) type B0 using 12.5 mm crushed stone aggregates as in chajjas complete all as specified.(Note:-Reinforcement and form work shall be measured and paid separately.) |
| 79 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. |
| 80 | M&L for Brick work with fly ash modular bricks straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6) complete all as specified and directed. |
| 81 | M&L for brick work using fly ash bricks straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:3) complete all as specified and directed. |
| 82 | Taking down PVC/CI pipe jointed in cement mortar taking out of wall and eaves gutters and rainwater pipes (any size or pattern) and including all fittings, heads, shoes, bends, swan-necks etc. including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories. |
| 83 | S&F for 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in floors or trenches complete as in repair all as specified and directed. |
| 84 | S &F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified. |
| 85 | S&F for 110mm dia PVC (SWR) pipes type \"B\" single socketed in any length with rubber ring joints, laid in trenches or in floor complete as in repair all as specified and directed. |
| 86 | S & F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified. |
| 87 | M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 100 mm bore SGSW pipe complete all as specified and directed. |
| 88 | S&F for PVC SWR bends of 75 mm bore with access door complete all as specified and directed. |
| 89 | S&F for PVC SWR bends of 110 mm bore withaccess doorcomplete all as specified and directed. |
| 90 | Schedule \"A\" Part-II (E/M) Works:Supply only submersible pumpset with pump IS-8034 and motor IS-9283, assembly heavy duty, star rated, 3 phase, 415 volt, ISI marked latest for use in bore well for handling clear cold water, Head range: 14-18 mtr, Discharge: 30-90 Cum/Hrs, Capacity-15 HP complete all as specified and directed by Engineer-in-Charge.(Note:- Submersible pump set with pumb and motorShall be taken on charge duly entered in ledger) |
| 91 | Supply only for 20 HP, 15KW fully automatic star-delta starter in sheet-steel enclosure motor rating 415V, 50 Hz, 3Ph of capacity relay range 15-22A complete all as specified and directed.(Note:- Submersible pump set with pumb and motorShall be taken on charge duly entered in ledger) |
| 92 | Supply only submersible cable PVC inuslated & PVC sheated Industrial Cable (flat) for submersible pump motors 1100volts 3Ph, 3 core of size 6 sqmm all as specified and directed by Engineer-in-Charge.(Note:- Submersible pump set with pumb and motorShall be taken on charge duly entered in ledger) |
| 93 | Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications complete all as specified and directed. |
| 94 | M&L for point wiring for one light point/fan point/exhaust fan point controlled by one-one way 5/6 amp switchwith 1.5 Sqmm. (nominal area) single core FRLSH,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including non metalic rigid PVCconduit of 20mm dia (Medium grade)complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLSH, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making goodthe diturbed surfaces compete all as specified and directed.(Note:-(a) Three run of copper conductor of required size and one run of PVC conduit and accessories measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth.(b) Quoted rates shall be deemed for conduit & accessories, cover plate and sunken box of suitable size, cutting chases of wall etc. and making good disturbed wall). |
| 95 | Description all as per srl item No. 94 above but for one 5 pin, socket outlet, 6 Amps on independent board but not below the switch board of light points in the same verticle plane complete all as specified and directed. |
| 96 | Description all as per srl item No. 94 above but for one 5 pin, socket out 6 Amps on same board with other switches complete all as specified and directed. |
| 97 | Description all as per Serial item No 94 above but for one 6 pin 15 Amp socket outlet independent with2.5 sqmm PVC insulated FRLSH multistraind copper cable with 2.5 sqmm single core multistraind FRLSH copper cable as earthling lead complete all as specified and directed. |
| 98 | S&F for switch modular typeone way 6 Amps 230 volts, with one module, complete all as specified and directed. |
| 99 | S&F for switch modular typeone way 16 Amps 230 volts, with one module with indicator complete all as specified and directed. |
| 100 | S&F for socket shuttered modular type6 Amps , 2/3 pin combined, 230 volts, with two module, complete all as specified and directed. |
| 101 | S&F for socket shuttered modular type6/16Amps Amps , 6 pin combinded, 230 volts, with two module, complete all as specified and directed. |
| 102 | S&F for lamp holder insulated body PVC/ Polycabonate type with back plate suitable for batten/angular/pendent fittings complete as in repair all as specified and directed. |
| 103 | S&F for ceiling rose 3 phase, PVC/polycarbonate isolated body surface bakelite2 to 3 terminals fixed to wall/ceiling complete all as specified and directed. |
| 104 | M&L for LED Tube light fitting, complete with 1x 18 watts, 220V, AC decorative box type with driver, holder in andincluding LED tube light connection complete prewiredand connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height complete as in repair all as specified and directed. (Make :- Havells cat No LHEXACP7IN1W020 or equivalent in Crompton/Philips) |
| 105 | M&L forsub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi strandedduly colour coded cable drawn through and including PVC conduit of size 25mm dia or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceable sub main wiring items complete all as specified and directed.(Note : -(a) 02 run of 4 sqmm single core copper conductor cable and 01 run of 4 sqmm single core copper conductor and 01 run of PVC conduit shall be measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth). (b) Quoted rates shall be deemed for conduit & accessories, cover plate and box of suitable module, cutting chases of wall etc. and making good disturbed wall |
| 106 | M&L for sheet metal enclosure MCB distribution board, double door (metal) single pole and neutral with IP-43 and IK 09 protection single phase 240 volts 8 way, including suitable size copper bus bar of 200 amp and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete as in repair all as specified and directed. (Note:-MCBs will be measured separately.) |
| 107 | M&L for MCB, SPN, 240 volts, 63 amps with rupturing capacity 10 KA, \"C\" curve, including providing thimble for out going cables complete all as specified and directed. |
| 108 | M&L for MCB, SP, 240 volts, 6-32 amps with rupturing capacity 10 KA, \"C\" curve, including providing thimble for out going cables complete all as specified and directed. |
| 109 | S & F for modular white cover plate with frame, 2 module complete all as specified. |
| 110 | S & F formodular white cover plate with frame, 8 modulewith blank switches as required complete all as specified. |
| 111 | Supply, install, commissioning and testing vertical storage water heater (geyser) 5 star rated as per BEE norms electricity operated suitable for 230 volts, 50 hz, AC supply system complete with porcelen/ glass coated insulated heating element, copper tank, external thermostat and docorative of capacity 25 Ltrs, including 01 No. PVC connection for hot water and 01 No PVC connection for cold water connected with CP brass unions one on each side including fixing on 04 Nos 16mm dia 150mm long MS bolts and nuts with vasher grouted in wall with cement mortar (1:3) including safety valve, non return valve 15mm dia (ISI marked) with suitable bolts and nuts complete all as specified and directed. (Make: Havells/ Recold/ Bajaj/ Crompton/ Usha) |
| 112 | S&F for switch socket combination 5 in 1, 5 pin, 6/16 amp flush type complete all as specified and directed. |
| 113 | S&F for 15 mm bore galvanised iron GI tubing (medium grade) with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specified and directed. |
| 114 | S&F for 15 mm dia angular stop cock chromium plated fancy type complete all as specified and directed. |
| 115 | M&L for 15mm diabib tap cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwedfor iron pipe complete all as specified and directed. |
| 116 | M&L forsub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi strandedduly colour coded cable drawn through and including PVC conduit of size 25mm dia or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.(Note : -(a) 02 run of 4 sqmm single core copper conductor cable and 01 run of 4 sqmm single core copper conductor and 01 run of PVC conduit shall be measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth). (b) Quoted rates shall be deemed for conduit & accessories, cover plate and box of suitable module, cutting chases of wall etc. and making good disturbed wall |
| 117 | M&L for MCB, SPN, 240 volts, 32 amps with rupturing capacity 10 KA, \"C\" curve, including providing thimble for out going cables complete all as specified and directed. |
| 118 | M&L for sheet metal enclosure MCB distribution board, single door (metal) single pole and neutral with IP-30 and IK 09 protection single phase 240 volts 2 way, including suitable size copper bus bar of 100 amp and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note:-MCBs will be measured separately.) |
