Tender For Beautification And Tourism Development Work Of Sun Temple Of Devkali Village Of Sikandarpur Tehsil Of Ballia District, Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as ifirected within a lead of m All kinds of soil. Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, aho including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc, complete Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level 1:48 (1 Cement: 4 coarse sand (zone) derived from natural sources: B graded stone aggregate 40 mm nominal size derived from natural sourceal Supplying and filling in pinth with sand under floors, including watering, ramming, consolidating and dressing complete Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion): With Chlorpyriphos/Lindane E.C. 20% with 13% concentration. Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of certtering, shuttering, finishing and reinforcement All work up to plinth level 1:1.5:3 (1 cement: 1.5 coarse sand (zone-iii) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) Reinforced cement concrete work in walls fany thickness), including attached plasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering shuttering finishing and reinforcement: 1:1.5:3 (1 cement: 15 coarse sand(zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size Iderived from natural sources) Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window tills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1 cement: 1.5 coarse sand(zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3-(1 cement: 1.5 coarse sand(zone lijderived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement: 6 coarse sandi Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 1 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 12.5mm.nominal size derived from natural sources) Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in foundations and plinth Cement mortar 1:4 (1 cement: 4 coarse sand) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Jupto plinth level. Thermo-Mechanically Treated bars of grade Fe-5000 or more 15 mm cement plaster on rough side of single or half brick wall of mix 1:41 cement: 4 coarse sand) 15 mm cement plaster on rough side of single or half brick wall of mix 1:6 11 cement: & coarse sand) Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete: New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litie New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Providing and fixing ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all coloun, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry 3.3kg per som, including pointing in white cement mixed with pigment of matching shade complete. Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). Size of Tile 600x600 mm Centering and shuttening including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete Columns, Pillars, Piers, Abutments, Posts and Struts Lintels, beams, plinth beams, girders, bressumers and cantilevers Suspended floors, roofs, landings, balconies and access platform Lintels, beams, plinth beams, girders, bressumers and cantilevers Providing and fixing of laminated PVC flush doors of 25mm thickness water proof and moisture proof Providing and fising of UPVC top hung casement window Providing and fixing water closet squatting pan Indian type WC pan with 100 mm sand cast iron Por 5 trap, 10 litre low level white PVC flushing cistem, including flush pipe, with manually controlled device (handle lever) conforming to 15: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistem, including flush pipe, with manually controlled device (handle lever), conforming to 15: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C pan with 151 marked white solid plastic seat and lid Providing and fixing white vitreous china flat back or wall corner type lipped frant urinal basin of 430x260x350 mm and 1340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and 6.1 clampscomplete, including painting of fittings and brackets, cutting and making good the walls and One urinal basin with 5 litre white PVC. automatic flushing cistern Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes Jand fittinen Providing and fising square mouth $. W. gully trap class SP Icomplete with CI grating brick masonry chamber with water tight Cl. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4 50 kg and frame to be not less than 270 kas nec standard desion 100x100 mm size type With common bumt clay (non modular) bricks of class-150 Providing and fixing Chlorinated Polyvinyl Chloride (PU) pipe, having thermal stahility fre tut & rold wate supply, including all CPVC plain & brass threaded fittings, c fxing the pipe with clamps at 100 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 120 mm nominal outer diz Pipes Providing & Placing of Looking Mirror pasted on wall with the help of silicon having edges beveled, all complete as per drawing, specification and direction as approved by the Architect/Engineer Wiring point for light with 1.5 sqmm FRISH insulated multistrand single core PVC copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting complete with 1.5 sq.mm. FRLSH copper earth contunity wire modular type & switch ceiling rose/angle batten holder on 3mm thick phenolic paminated backalite sheet etc.complete in all respects as directed including matching colour wash Wiring point for fan/fresh air fan (light duty exhaust fan) with 15 sqmm.FRLSH multistrand single core PVC insulated. copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 15 sq.mm. FRLSH copper earth contunity wire, modular type switch rose/angle/batten holder on 3mm thick phenolic ceiling paminated backalite sheet etc.complete in all respecttas Supply and fixing of power plug with 154/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M5 box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover amm thick fixed with bass machine screw and run washes Supply and wiring of submain with two number 15 sq.mm. PVC insulated 1100 V grade single core copper conductor cable in mm dia heavy duty (2mm thick) PVC conduit with 1 nos 1.5 sq. mm. FALSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in al respect, Supply fixing and concealing of 20mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work. asdirected at site by the engineer in charge. Supply and fixing of recess mounting round 15 TO 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AAA Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer- Incharge. 25 sq. mm 3-1/2 S&F surface/Flush mounting 12ways TPN distribution Land with athlitiumal metal shuu without MCB Lumiele in all respect,as directed at site by Engineer in charge. CAT-A Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and 5.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common bumt clay FPS (non modular) bricks of class designation 7.5 construction of septic tank for 20 users Constructing brick masonry road guily chamber 45x45x775cm with bricks in cement mortar 1:4 (1 cement: 4 coarse sand) with precast R.C.C. vertical grating complete as per standard design: With common bunt clay FPS, (non modular) bricks of class detionation Providing and placing on terrace (at all floor levels) polyethylene water storage tank, 15: 12701 marked, with cover and suitable Incking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the haus wnnort for tank Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step-CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes 20 mm nominal outer dia Pipes Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 16 (1 cement: 6 coarse sand) Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm pominal sue store meregate 12 mm cement plaster finished with a floating coat of neat cement of mix: 14/1 petnent: 4 fine sand) S&F surface/Flush mounting 12ways TPN distribution Land with athlitiumal metal shuu without MCB Lumiele in all respect,as directed at site by Engineer in charge. CAT-A Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and 5.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common bumt clay FPS (non modular) bricks of class designation 7.5 construction of septic tank for 20 users Constructing brick masonry road guily chamber 45x45x775cm with bricks in cement mortar 1:4 (1 cement: 4 coarse sand) with precast R.C.C. vertical grating complete as per standard design: With common bunt clay FPS, (non modular) bricks of class detionation Providing and placing on terrace (at all floor levels) polyethylene water storage tank, 15: 12701 marked, with cover and suitable Incking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the haus wnnort for tank Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step-CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes 20 mm nominal outer dia Pipes Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 16 (1 cement: 6 coarse sand) Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm pominal sue store meregate 12 mm cement plaster finished with a floating coat of neat cement of mix: 14/1 petnent: 4 fine sand) Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to 15: 13592 Type A, including jointing with seal ring conforming to 15: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated sod & then returning the sodas remaired in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia Providing laying and joining glazed stone ware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete. 150mm diameter Providing & laying cement concrete 1:5:10(1 cement coarse sand 10 graded stone aggregate 40mm nominal size) alraund 5.W. Pipes including bed concrete as per standard design. 150mm diameter S.W. Pipe Constructing brick masonry manhole in cement mortar 1:4 (1 cement:4 coarse sand) RCC top slab with 1:2:4 mix (1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4.8 mix (1 cement : 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement 3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1-cement 2 coarse sand:4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including Cl cover with frame (light duty) 455x10mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 29 ke and weight of frame 15kg) With FPS brickas of class designation 75 For Sewer Line Extra for depth of man hole sure 90x80 cm Inside size 90x120 cm & 90 cm deep including C. cover with frame (medium duty) total wt. of cover & frame to be not less than 116 Kg (wt. of cover 58 Kg & wt. of frame 58 Kg Extra for depth of man hole size 90x120 cm Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per 5: 10910 on 12mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribihing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturess permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm. nominal size) complete as per design. Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar (1 cement 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete: For pipes 300 to 250mm diameter Excavating trenches in all kind of soil of required width for pipes, cables etc, including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the sod as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposug of surplus excavated soil as directed within a lead of Som. Pipes, cables etc. not exceeding 80mm dia. Provding and fixing gun metal non return valve of approved quality berewed end) 150 mm nominal bore Vertical Providing & fixing G.1. pipes complete with G.1. fittings including tenching and refilling etc. External work 32mm nominal bore. 50mm nominal bore Providing & fixing sand of grading zone V or coaser grade alround the G. Pipes in external work 32 mm diameter pipe 150 mm diameter pipe Providing and fixing gate valve (with cap complete with bolts, Inuts, rubber insertion etc. 32 mm nominal bore 150 mm nominal bore Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 14 (1 cement:4 coarse sand) for sluice valve, with CI. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement: 5 fine sand 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: Making connection of G., distribution branch with Gl. main of following sizes by providing and fixing tee, including cutting and threading the nine etc. complete 125 to 40 mm dia nominal bore 150 to 80 mm dia nominal bore Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer in-charge. All kinds of soil Filling available excavated earth (excluding rock) in trenches, plirith, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of Skm also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete Providing and laying cement concrete 1:4:8 (I cement 4 course sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour 7 & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & floors Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete: Treatment of sol under existing floors using chemical emulsion @one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floor. With Chlorpyriphos/Linadane E.C. 20% with 1% concentration Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1.1.5:3 (1 cement: 1.5 coarse sandizone derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from Ground Floor Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from Ground Floor Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived fram Above Plinth Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: 1:15:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size Ide rived from natural sources) Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering. finishing and reinforcement-All work up to plinth level: 1:15:3 (1 cement: 15 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size Ide rived from natural sources) Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1. cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from Ground Floor Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1.cement: 6 coarse sandi Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5 mm.nominal sizel Painting on D.P.C. with two coats of airtilown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement: 6 coarse sandi Ground Floor Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement:4 coarse sandi Ground Floor Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe 5000 or more Ground Floor 15 mm cement plaster on rough side of single or half brick wall of max: 1:4 (1 cement: 4 coarse sand). 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand) Ground Floor 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand) Ground Floor Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement 12 mm cement plaster Ground Floor Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections, Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 15: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to 1.5. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry@ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1-4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Ground Floar Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1-4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, (skirting) Ground Floor Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. Providing and fixing ISI marked flush door shutters conforming to 15: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. Single leaf (b) Double leaf Both side laminated Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (±0.2 mm), comers of the door frame to be lointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (±0.1 mm) wall thickness and 3 nos, stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineerin including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single/double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension Le. in depth & width of profile shall be acceptable. Three track three panels sliding window with two glazed & one wire mesh panels with alluminium channel for roller track, wool pile, nylon rollers with ss. 304 body. Using R2 series with foame (70mm & above)x(40 mm & above) & both glazed and fly screen sash (25 mm & above)x(50mm & above with zinc alloy (zamak) powder coated touch lock with hook (Height up to 1.20 meteri Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer. (For Internal wall surface) Ground Floor Finishing walls with Premium Acrylic Smooth exterior paint with. Silicone additives of required shade:New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (Outer surface) Ground floor Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For ceiling surface) Ground floor Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R.-13.80 - (a) Ground Floor Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-incharge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-incharge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with n Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. Providing & faing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete (a) 300 mm x 10mm (b) 200 x 10mm Providing and fixing stainless steel handies with screws etc. complete (a) 150 mm Providing & foxing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with: 4.0 mm thick glass panes Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sandizone-II): 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering. roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be prepainted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece Providing and fixing 1mm thick M.5. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick Columns, Pillars, Piers, Abutments, Posts and Struts Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to 15: 13592 Type A. including jointing with seal ring conforming to 15: 5382 leaving 10 mm gap for thermal expansion i Sinile socketed nines 110mm diameter. Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1-3 (1 cement: 3-coarse sand) and a coat of neat cement punning rounding the edges and making and finishing Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall ate complete 110mm Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams Wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.1. box and earthing the point with 15 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C Witing for circuit/sub-main wiring along with earth wire with the following size of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 2X1.5 sqmm + 1x1.5 sqmm earth wire 2X2.5 sqmm + 1x 2.5 sqmm earth wire 2X4.0 sqmm + 1x 4.0 sqmm earth wire Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Supplying and foxing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. Supplying and fixing suitable size Gi box with modular plate and cover in front on surface or in recess including providing and foxing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch.connection etc as required Supplying and fing suitable size Gi box with modular plate and cover in front on surface or in recess including providing and foxing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connection etc. as required. Instalation, testing & commissioning of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLSCFL/LED lamps per fitting, complete with all accessories including connection etc, as required. Installation, testing and commissioning of prewired, flourescent fitting/compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling/wall, including connection with 1.5 sq. mm. PVC insulated, copper conductor, single core cable etc. as required. Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm/ with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. Numbering of ceiling fan/ exhaust fan/fluorescent fittings as required Providing and fixing circular/Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper banding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia round headed screwed, one loc at the conrners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Disect Current(BLDC) motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value CM/M/W) minimum 6, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per 15: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise 75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. DISTRIBUTION BOARDS, MCBS & ISOLATORS: Supplying and fixing following way, Horizontal type three pole and neutral MCB distribution board, 415 volts on surface /recess complete with, tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolators). 4 way (4+12), Double door Supplying and foxing 5 amps. to 32 amps. rating, 240 volts C series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole Supplying and foxing single pole, blanking plate in the existing MCB DB complete etc., as required. Supply and fixing following rateing four pole, 415 V, isolator in the existing existing MCB DB complete with connections, testine and commissioning etc. as required. 40 A Suplying and fixing cable end box(Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution borad, 415 Volts, on surface/recess, complete with testing and commissoning ect. As required. For 4 way, Double Door TPNMCBDB Earthing with Gl earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and sait as required. Supplying and Laying of 25 mm X 3 mm G.l strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.1. nut bolt & spring washer spaced at 50mml Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc, as required Upto 35 sq. mm Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sqmm. (19mm) 4 X 10 sqmm. (25mm) Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.L. fittings including trenching 175 cm deep) and refilling etc as required. 100 mm Dia Supply of following size of 1.1 KV grade multicore aluminium conductor PVC sheathed armoured cable as per 15 1554, Make- Polycab or Eq 10 sqmm 2 core 10 sqmm 4 core SUPPLY OF LIGHT FIXTURES: Supply of LED Tube Light with batten suitable for up to 1820 watt LED tube light complete including tube etc. on surface/Pendent complete in all respect. Make Philips or Ea Supply of recess/Surface/Pendent mounting round 10 to 15 watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set complete in all respects. Make-Philins or En Supply of service bracket of 50mm. Dia 4 meter long fabricated from class B G.I. pipe complete with two bend, socket, wall clamps. 7/3.15 mm G.L. stay wire, stay insulators etc..complete in all respects Supply of LED street light fitting having die cast aluminium body. and diffuser/reflector with driver set suitable for 75 watt to 90 Watt confirming to IP 66 protection complete in all respect Make Philins or Fa 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand) with joints finished flush. Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. Providing and laying cement concrete 1:4:8 (1 cement: 4 coarse sand B graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & Prtc required for proper completion of the work and curing complete also including cost of formwork. in foundation & floors Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete Along extemal wall where the apron is not provided using chemical emulsion@7.5 litres/sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc, complete: With Chlorpyriphos/Lindane EC 20% with 1% concentration Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1 cement: 15 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources), Lintel Ground Floor As in item no. 6 above but for slabs (Using M-20 Mix concrete). Ground Floor As in item 6 but for the lighter beams ie, having spans upto 6 m. (Using M-20Mix concrete) Ground Floor Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: As in item 6 above but in R.C.C. columns(Using M-20 Mix concrete) Ground Floor Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Ground Floor Same as in item no. 14 but in 1:4 cement and coarse sand mortar in superstructure for wall thickness 12 cms & below brick work Ground Floor P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. Ground Floor 15 mm plinth plaster (1 cement 4 coarse sand) 15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor twn level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement: 6 coarse sand Ground Floor 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. (1)1 cement: 6 coarse sand. Ground Floor 12mm thick plaster in 1:3 on ceiling and soffits of stairs upto floor two level Ground Floor Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Ground floor Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, windowsills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Ground Floor Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: Ground Floor Finishing walls with Acrylic smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 Ltr./10 Sqm over and including base coat of water proofing cement paint anplied @ 220 ke/10 Sam Ground Floor Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats (For Internal ceiling surface) Ground Floor Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete Ground Floor Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-incharge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade :Both face dressed.Red sand stone Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement: 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. Red sand stone ADD FOR INTERNAL ELECTRIFICATION Earth work in exacavation in t. in ordinary soil loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer ifc with in alead of 50m. Providing and laying in cement concrete 1:4:8 (1 cement 4 coarse sand:8 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors Class M-150 brick work in 1:4 cement coarse sand (of 2.5 fineness modulus) mortar in foundation & plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, desigri & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Cost of Lighiting Work (Solar) Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge All kinds of soil Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering All work up to plinthlevel:1:4:8 (1 Cement: 4 coarse sand: 8 graded stone ageregate 40mm nominal size) R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone grit in the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its foing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works, including cost of binding wire. The rate excludes making of drip course which shall be paid extra. Ground Floor As in item 3 above but in R.C.C. Raft foundation and footing with approved stone ballast. (Using 1:1.5:3 Mix concrete) First Class brick work in 1:6 cement and coarse sand of 1.25 F.M. mortar in foundation and plinth including supply of all materials, labour, tools and plants etc, required for proper completion of the work (1:6 cement & coarse sandi P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing.30 mm thick Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand), including making the necessary chases Supplying and stacking sludge at site including royalty and carriage up to 5 km (sludge measured in stacks will be reduced by 8% for paymenti. Carrigae of sludge upto 5 K.M. Supplying and stacking at site dump manure from approved source including carriage upto 1 km (manure measured in stacks will be reduced by 8% for payment): Screened through sieve of LS. designation 4.75 mm Carrigae of manure upto 5 KM. Moxing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge. Spreading of sludge, dump manure or/and good earth in required thickness (cost of sludge dump manure or/and good earth to be paid separately) Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20%: 1 part of stacked volume of manure after reduction by 8%), flooding with water, dressing, including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately). Holes 0.9 m dia, and 0.90 m deep Plantation of Trees, Shrubs, and Hedge at site l/c watering and removal of unserveiceable materials as per direction of officer in charge (excluding cast of plant & water). Trees Plant Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags Providing and stacking of Bottle palm of ht. 270-300 cm battom girth 40-50 cm well developed in big HDPE bags as per direction Jof the officer-in-charge Providing and stacking of Foxtail palm of ht. 180-210 cm bottom girth 25- 30 cm well developed in big size HDPE bags as per direction of the officer-in-charge Providing and stacking of Foxtail palm of ht. 180-210 cm bottom girth 25- 30 cm well developed in big size HDPE bags as per direction of the officer-in-charge Grassing with selection No.1 grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the good earth shall be paid for senaratelui. With grass Tud Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x6mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia. and 30 mm long boits, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the treeguard near the middle height and lettered CPWD/PWD/any other approved name. The Tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge. Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soill Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand B graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & Boo Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:15:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from Ground Floor Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to alinth level 1:15:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size de rived from natural sources) Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:611 cement: 6 coarse sand) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe 5000 or more Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing.30 mm thick Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1-2 (1 cement: 2 coarse sand), including making the necessary chases Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby Cost of Stone writing Supply and fixing of decorative 8 to 16 Watt LED bollard luminaire with driver set confirming to IP 65 protection complete in all respect Cat-AAA Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with driver set E suitbale for 40 to 50 Watt. Conforming to IP 65/66 protection complete in all respect (CAT-AAA) External W/S arrangement, T.W. boring of 150mm dia with 100mm dia P.V.C. pipe assembly, 1.5 H.P. submersible pump including supply of all accessories starter, panel etc. & pipe arrangement etc. 14 PVC pipe of ISI mark [14 Kg pressure) P/F 2 GI pipe (B) class. NYLon mesh for filter. Plastic dori Solvent from 4 End cap 4 Submersible Cap 12 MS clamp (Heavy) 12 Gl elbow 1.5 HP 9 Stage Submersible Pump of ISI mark With automatic panel. 2*6 Gi nipple 2.5 5qm. Submersible cable. Drilling Charges for 6 dia tubewell. Pea Gravel 2 Ms Socket. Cartage of material upto site
