Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | DORMITORY+DIGITAL LIBRARY+PLATFORMEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil1.5 Mtr To 3.0 Mtr |
| 3 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil3.0 Mtr To 4.5 Mtr |
| 4 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil4.5 Mtr To 6.0 Mtr |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form forWalls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form forEdges of slabs and breaks in floors and walls Under 20 cm wide |
| 15 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)G.F. |
| 16 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)F.F. |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 18 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 19 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)G.F. |
| 20 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)F.F. |
| 21 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class - 150 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)G.F. |
| 22 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class - 150 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)F.F. |
| 23 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 24 | Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the coloumn pitswall tench basement excavation top surface if plinth filling junction of wall and floor along the external perimer of binding expansion joints,surrounding of pipes and conduits etc.complete(plinth area of the building at ground floor only shall be measuredas per I.S.6313(Part ll 1981) aldrine emulsifiable concrete or any other approved material such as hepthachlor or chlordance will be used.The rate of application of chemical emulsion shall be as follows:-(1)treatment for masonary & foundation 5 litres per sq.m.(2)back fill in immediate contract with foundation 7.5 litre per sq.m(3)treatment of top surface of plinth filling 5 liters per sq.m.(4)treatment of soil along external parameter of building 7.50 lire per sqm. (For payment plinth area to be measured as per IS Code). |
| 25 | Providing and fixing SS sliding door bolts ISI marked anodised transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm. |
| 26 | Providing and fixing SS tower bolts ISI marked anodised transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm. |
| 27 | Providing and fixing SS handles ISI marked anodised transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm. |
| 28 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete |
| 29 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 30 | Teak wooden door |
| 31 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part |!) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 32 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming toIS: 2202 (Part I) |
| 33 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). |
| 34 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 35 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 36 | Providing & Fixing of Aluminium window with 5 mm glass pans.W1 |
| 37 | Providing & Fixing of Aluminium window with 5 mm glass pans.W2 |
| 38 | Providing & Fixing of Aluminium window with 5 mm glass pans.W3 |
| 39 | Providing & Fixing of Aluminium window with 5 mm glass pans.W4 |
| 40 | Providing & Fixing of Aluminium window with 5 mm glass pans.V2 |
| 41 | Providing & Fixing of Aluminium window with 5 mm glass pans.S1 |
| 42 | Providing & Fixing of Aluminium window with 5 mm glass pans.S2 |
| 43 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 44 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 45 | Providing and fixing ball bearing for rolling shutters. |
| 46 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces |
| 47 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of slab (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 48 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 49 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 50 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 51 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 52 | Add for plaster groove in plastered surface or moulding to R.C.C. projections. |
| 53 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 54 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 55 | Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water abDSRption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. With out base concrete Glazed Vitrified tiles Matt/Antiskid finish of 600X600mm size. |
| 56 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick |
| 57 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 58 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 59 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shadeArea of slab over 0.50 sqm |
| 60 | Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge |
| 61 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 62 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 63 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 64 | Finishing walls with Putty approved brand and manufacture and of required shade on undecorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work. |
| 65 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 66 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 67 | Supply and filling in sunken with brick bats under floors, including watering, ramming, consolidating and dressing complete. |
| 68 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 69 | Providing and fixing false ceiling at all heights including providing andfixing of frame work made of special sections, power pressed from M.S.sheets and galvanized with zinc coating of 120 gms/sqm (both sideinclusive) as per IS : 277 and consisting of angle cleats of size 25 mmwide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the anglehangers of 25x10x0.50 mm of required length with nuts & bolts of requiredsize and other end of angle hanger fixed with intermediate G.]. channels45x15x0.9 mm running at the spacing of 1200 mm centre to centre, towhich the ceiling section 0.5 mm thick bottom wedge of 80 mm withtapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centreto centre, shall be fixed in a direction perpendicular to G.|. intermediatechannel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter ofceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre ,with 25 mm long dry wall screws @ 230 mm interval, including fixing ofgypsum board to ceiling section and perimeter channel with the help ofdry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing andfinishing to a flush finish of tapered and square edges of the board withrecommended jointing compound , jointing tapes , finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and twocoats of primer suitable for board, all as per manufacturer’s specificationand also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed,all complete as per drawings, specification and direction of the Engineerin Charge but excluding the cost of painting with12.5 mm thick tapered edge gypsum moisture resistant board |
| 70 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 71 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. |
| 72 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. For 100 mm dia pipe |
| 73 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler |
| 74 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° |
| 75 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe(Plain) |
| 76 | Providing and fixing PTMT grating of approved quality and colour.Circular type 100 mm nominal size diameter |
| 77 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 78 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 150 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 79 | Construction of Apron drain ofwidth 150mm and depth as per required of site but minimum 150 mm with neat finish & required slope as per apporoved by E/I. |
| 80 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m? |
| 81 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.80 mm thick with zinc coating not less than 275 gm/m² |
| 82 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 83 | Providing and fixing of Ornamental wooden decorated columns in various elements for all levels. solid Teak wood load bearing columns with solid t wood crowns supported on hand-carved Wooden bases.Wood shall be free from cracks, lines stains and even in shade for each element . The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size) moulding. The carving and molding work shall be of very good qualityapproved make as required and as approved by the Architects and Engineer in charge |
| 84 | Supply & fixing Nuvocotto Euro Dark Chocolate clay tiles of 10X16 inches on roof including the cost of Ridge, typical caly tile, edge tiles and inlcusion of glass tiles in color and finish as per drawing approved from Architect in charge, and supply of all materials labours & tools etc required for safe erection and cost of adhesive, waterproof membrane and MS frame of L profile/rectangular hollow sections required for fixing and supprting the tiles., also includes the cost of all the necessary fitting and required for completion of the work as per Architect In charge. |
| 85 | Supply & fixing Ornamental clay tiles of 10X16 inches for ceiling including the cost of Ridge, typical caly tile, edge tiles and inlcusion of glass tiles in color and finish as per drawing approved from Architect in charge, and supply of all materials labours & tools etc required for safe erection and cost of adhesive, waterproof membrane also includes the cost of all the necessary fitting and required for completion of the work as per Architect In charge. |
| 86 | Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge. |
| 87 | Providing and fixing of Ornamnetal woodenTeak wood door shall be free from cracks, lines stains and even in shade for each element . The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size) moulding. The carving and molding work shall be of very good qualityapproved make as required and as approved by the Architects In charge. |
| 88 | The providing and fixing of ornamental mashrabiya with a customized design and size crafted from high-quality Teak wood. The customization will be based on the designs and sizes outlined in the attached drawings. The Teak wood used must meet impeccable standards, ensuring it is free from cracks, lines, stains, and exhibits uniform shading for each element. The execution of the work will involve various processes, such as manual or machine carving, ornamental detailing, traditional craftsmanship, figure work of any type and size, as well as molding. All carving, molding, and CNC work must adhere to stringent quality standards, utilizing approved materials and methods specified and approved by the Architects in charge. |
| 89 | Providing and installation of a crafted koomb or kalasam of customised size and shape not less than 300mm heightmade of terracotta blocks, with finishes achieved through cutting, carving, engraving, etc., also includes the cost of all necessary fittings required for the completion of the work as per the Architect In charge. |
| 90 | Providing and Fixing of Wooden Louvered of Teak wood finish in a frame of 30x30mm thk. also includes the cost of all necessary fittings required for the completion of the work as per the Architect In charge. |
| 91 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10metre height, backing filled with a grout of average 12 mm thick cementmortar 1:3 (1 cement : 3 coarse sand) including pointing in white cementmortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigmentmatching the stone shade : (To be secured to the backing and the sidesby means of cramps and pins which shall be paid for separately) : 70 mm thick - Red sand stone - Exposed face machine cut and table rubbed with rough backing. |
| 92 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 93 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 94 | Washed stone grit plaster on exterior walls in two layers with customised stone, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Architect-in-charge. |
| 95 | Hand Chiseling and edging on supplied stone to gain the desired finish as approved by Architect in charge; and supply and Layingwater soluble penetrative solution for waterproofing of masonry building material &with Nano technology based as it provides molecular level hydrophobicity to inorganic substrate .The product is based on organosilicon chemistry, hence reacts with the inorganic substrate surface, seals the surface uto a depth of 2-3 mm and provides long service life where Nano size allows penetration deep into substrate that provides 20+ years water repellency.(Zycosil/Pratt & Lamber or Equivalent) including cost of all materials, labour tools and plants etc. required for proper completion of the work. |
| 96 | Supply & fixing Teak Wood Roofing Elevation Border Design Sheet of approved thickness (not less than 12-20mm) and width minimum: 200 mm;also includes the cost of all the necessary fitting and required for completion of the work as per Architect in charge. |
| 97 | Supply & fixing Crafted from premium solid teak wood Bracket of customized size and design; also includes the cost of all the necessary fitting and required for completion of the work as per Architect in charge. |
| 98 | Below Raft / Footings / Grade Slab with mechanicaly thermofused fully bonded HDPE membrane: Supplying and installing 1.5 mm composite thick fully bonded weldable HDPE membrane conforming to IS 16471:2017 requirements of UG waterproofing structures, requirements to provide Type A fully bonded protection of UG waterproofing structures. The membrane should be minimum 2.4 m wide comprising of an HDPE layer and a pressure sensitive adhesive layer which is covered by a weather proof protective layer with lap Joint Strength at overlaps >15000 N/m ASTM D 6392:2012. The membrane shall have minimum of 75mm side and end laps which shall be thermofused with leister of all the joints for assuring water-tightness and achieving monolithic membrane. End laps and side laps should be a minimum of 100 mm with the weld size of minimum 60 mm in case of a double weld system, comprising of two parallel welds of 20 mm wide each with a 20 mm air channel gap in between the two weld lines. The size of the membrane should not be less than 2.4 Mtr. x 20 Mtr. to minimise the joints. This membrane shall be continued over the vertical surface in case of confined areas, footings , toe portion and raft sides upto 200mm height above the Raft bottom , but terminated minimum 100mm below the top edge of the raft slab/footings and fixed as per recommendation. The waterprofing membrane shall have following minimum properties and waterproofing application shall be done by manufacturer authorised application team who is having minimum 10000 Sqm of Raft waterproofing works done with HDPE membrane in a single project.1) Lap Joint Strength at overlaps >15000 N/m ASTM D 6392:20122) Resist hydrostatic pressure of over 70 m head of water as per ASTM D5385 Modified3) Puncture Resistance of 800 N(± 5 to 10 %) as per ASTM E1544) Adhesion to concrete of > 880 N/m as per ASTM D 9035) Tensile strength of HDPE Without Adhesive (Film) of > 25 Mpa as per ASTM D412 modified6) Elongation of > 400% as per ASTM D 412 modified7) Low temperature Flexibility -25deg C - Pass |
| 99 | Retaining wall water proofingProviding & laying 1.5mm THK SBS modified self-adhesive, cross laminated HDPE valeron lining waterproofing membrane, Samshield, conforming to IS 16471:2017 Type A, requirements of UG waterproofing structures, over the solvent based bituminous Torchshield primer @ 4 sqm/litre. The lap with HDPE membrane shall be 100mm treated with double sided tape. The SBS membrane shall have Roll Size: 1 Mtr X 10 Mtr, Thickness DIN EN 1849-1, values 2.1, Puncture resistance > 200N as per ASTM E 154, Crack bridging (10 cycles) > 1.5mm as per ASTM C 836, Softening Point (oC) = 105 as per IS 1205/1978, Low temperature Flexibility – 10 deg C as per ASTM D 5147, Chemical Resistance (pH) as per ASTM D 543, Tensile Strength (Longitudinal) >3.5 Mpa, Hydrostatic pressure > 50M as per DIN 1048Providing and fixing HDPE protection having dimple height of 6 to 8 mm, as a protection board, over the waterproofing membrane for vertical surface stuck to the membrane by spot bonding method, usingsynthetic adhesive with butt joints etc. complete.***Note : Necessary back filling to be done by the main civil contractor within 2-3 days time progressively after installation of the membrane and protection board , taking care not to cause damage to the waterproofing treatment ..Termination of Membrane at 300mm above G.L. The waterproofing membrane shall be terminated on the vertical surface. The membrane shall be terminated either by creating a \"U\" shaped groove of approx. 10 mm x 10 mm size within the RCC retaining wall, tucking the membrane within the groove, followed by sealing the groove with polyurethane sealant/ epoxy mortar or alternatively the membrane shall be terminated by fixing a metal termination bar on the vertical surface, with butyl sealant between the metal plate and wall surface and sealed on top with P.U. sealant etc. complete. |
| 100 | Construction Joint TreatmentWater Swellable Bar:All Starter & Construction Joints of raft slab, retaining walls and water retaining structures : Providing and applying water swellable bar at starter & all construction joints, of c/s size of minimum 20mm X 5mm, Hydroswell HDP / Be-sealed Polybar, it shall have resistance to detoriation from salt water, volumetric expansion > 200%, Elongation > 400%, Shore A Hardness > 35, Tensile strength > 2 Mpa, Temperature resistance : (-) 20 to +75 deg C, Water head resistance > 50 m. It shall be fixed to the concrete using a gun grade hydrophilic fevicol adhesive / or mechanically fixed by binding wire with steel reinforcement, as recommended by manufacturer. Later post construction, groove cutting of the construction joints 25mm X 25mm size internally / externally, cleaning with compressed air and thereafter filling with Hydroblok 300 Polymer modified cementitious mortar, all as per manufacturers recommendations, etc, complete. |
| 101 | Supplying, designing, fabricating, transporting, hoisting and fixing in position mural works in good quality of 70 mm Red sandstone, and 18mm marble insertion and 6-10mm powder coated MS sheet in various elements for all levels. Stone shall be free from cracks, lines stains and even in shade for each element. The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding, etching, buffing and polishing. The carving and molding work shall be of very good quality. The work to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, (to be paid separetely) dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architect in charge |
| 102 | FAÇADE RENOVATIONDismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 103 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 104 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 105 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) |
| 106 | Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 107 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chaijjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 108 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 109 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 110 | Cost of ornamental cement concrete chattri of size 900X900X1500mm, including the cost of supplying, casting and installation of the chattri with dome , also including the cost of all the ornamental works in plaster, finishing with texture paint as per design and directions from Architect in charge |
| 111 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 112 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 40 mm thick |
| 113 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 114 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases. |
| 115 | Supplying, fabricating, transporting, hoisting and fixing in position good quality of 70 mm White/Red sandstone in various elements for all levels.The stone shall be Hand-chiseld and rough surface , reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), Text Engraving,ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding. The carving and molding work shall be of very good quality. The stones to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, (to be paid separetely) dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architects. |
| 116 | PLUMBINGProviding and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 117 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid |
| 118 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 119 | Providing and fixing Black Conical Bell Vessel wash basin for top/under counter mounting with fabricated MS brackets painted white synthetic enamel paintover a coat of primer of approved brand, 15 mm C.P. brass pillar tap of auto closing typewith pop-up waste, 32 mm C.P. brass bottle trap and pipe all of approved brand and manufacturer to wall with C.P. wall flange and rubber adopter for waste connection complete, including cutting and making good the walls & Floorswherever required.White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar tapsConical Bell vessel with tall pillar type Faucet |
| 120 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern |
| 121 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of two urinal basins with 10 litre white P.V.C. automatic flushing cistern |
| 122 | Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth. Granite stone of approved shade |
| 123 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board510x1040 mm bowl depth 250 mm |
| 124 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 125 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Flexible pipe32 mm dia |
| 126 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Flexible pipe40 mm dia |
| 127 | Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. |
| 128 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia |
| 129 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm |
| 130 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 131 | Providing and fixing toilet paper holder :C.P. brass |
| 132 | Providing and fixing soil, waste and vent pipes : Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 398975 mm O.D. |
| 133 | Providing and fixing soil, waste and vent pipes : Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989110 mm O.D. |
| 134 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.75 mm |
| 135 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 136 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :75 mm O.D. |
| 137 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :110 mm O.D. |
| 138 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. 75 mm |
| 139 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. 110 mm |
| 140 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accesDSRies for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Shoe (Plain)75 mm Shoe |
| 141 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accesDSRies for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Shoe (Plain)110 mm Shoe |
| 142 | Providing and fixing plain bend of required degree. Sand cast iron S&S as per IS - 398975 mm size |
| 143 | Providing and fixing plain bend of required degree. Sand cast iron S&S as per IS - 3989110 mm size |
| 144 | Providing and fixing heel rest sanitary bend Sand cast iron S&S as per IS - 398975 mm size |
| 145 | Providing and fixing heel rest sanitary bend Sand cast iron S&S as per IS - 3989110 mm size |
| 146 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Sand cast iron S&S as per IS - 398975 mm size |
| 147 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Sand cast iron S&S as per IS - 3989100 mm size |
| 148 | Providing and fixing terminal guard : Sand cast iron S&S as per IS - 398975 mm |
| 149 | Providing and fixing terminal guard : Sand cast iron S&S as per IS - 3989100 mm |
| 150 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 151 | Providing and fixingof fully automatic \"NO TOUCH\" durable & shock proof hand drier of approved make & manufacture suitable to operate on 220 volts, single phase 50 hz, A.C. power supply, 1500 Wattand directly plugged to power point complete in ABS plastic body having drying time 20-30 seconds complete as per direction of Architect in Charge.(Make : Kohler/Jaguar or Equivalent) |
| 152 | Providing, checking, storing and fixing Automatic Perfume Sprayer of approved quality, fixed to wall /door with concealed CP screws etc complete in all respect as directed by Architect-in-charge.(Make : Kohler/Jaguar or Equivalent) |
| 153 | Providing and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector complete with all respect as per direction of Architect in Charge. (Make : Kohler/Jaguar or Equivalent) |
| 154 | Providing and Fixing 2 No. hand rail size 600X100mmand grab bar 450mm longto mounted on the track (vertically and laterally) for handicaped toilet complete in all respects as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 155 | Providing and Installation of Soap dispenser & Holder complete in all respects as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 156 | Providing and fixing round mirror - matte black complete in all respects as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 157 | Providing and Fixing vanity in walnut finish complete in all respects as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 158 | Providing and Fixing Stall Partition complete in all respects as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 159 | Providing and Fixing Step Can Trash Bin as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 160 | Providing and Fixing Robe Hook as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 161 | Providing and Fixing Toilet Brush Holder in Brushed nickel as directed by Architect-in-charge. (Make : Kohler/Jaguar or Equivalent) |
| 162 | Providing & fixingPTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms |
| 163 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 164 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 15 mm nominal outer dia pipes |
| 165 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 20 mm nominal outer dia pipes |
| 166 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 25 mm nominal outer dia pipes |
| 167 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 32 mm nominal outer dia pipes |
| 168 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall20 mm nominal outer dia Pipes |
| 169 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall25 mm nominal outer dia Pipes |
| 170 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall32 mm nominal outer dia Pipes |
| 171 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.15 mm nominal outer dia pipes |
| 172 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes |
| 173 | Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. External work40 mm dia, nominal bore |
| 174 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)25mm dia, nominal bore |
| 175 | 32 mm dia, nominal bore |
| 176 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore |
| 177 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length15 mm nominal bore |
| 178 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet100 mm diameter |
| 179 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on walls)15 mm nominal outer dia pipes |
| 180 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on walls)20 mm nominal outer dia pipes |
| 181 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on walls)25 mm nominal outer dia pipes |
| 182 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on walls)32 mm nominal outer dia pipes |
| 183 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality40 mm dia, nominal bore |
| 184 | Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work 40 mm dia, nominal bore |
| 185 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore |
| 186 | Providing and fixingG.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)15mm nominal bore |
| 187 | Providing and fixingG.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)20mm nominal bore |
| 188 | Providing and fixingG.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)25mm nominal bore |
| 189 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 190 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:893115mm nominal bore |
| 191 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore |
| 192 | Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.15 mm nominal bore |
| 193 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming, watering etc. stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. |
| 194 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm O.D. |
| 195 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 160/150 mm diameter pipe |
| 196 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 197 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Fisnihed with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 198 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Fisnihed with a floating coat of neat cement complete as per standard design : Inside size 1200 x 1200mm and 1.0meter deep including C.I. Cover frame. |
| 199 | Extra for every additional depth of 0.10 metre or part there of main hole. Size 900 x 800 mm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 200 | Extra for every additional depth of 0.10 metre or part there of main hole. Size 1200 x 900mmWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 201 | ELECTRICALWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 202 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 203 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 204 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 205 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 206 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 207 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 208 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 209 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 210 | Supplying and drawingCo axial TV cable, RG-6 grade, 0.7 mm solid copper conductor, shieldedwith fine tinned copper braid and protected with PVCsheathin the existing surface/recessed steel/PVC conduit as required. |
| 211 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm |
| 212 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 213 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch |
| 214 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet |
| 215 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet |
| 216 | Supplying and fixing Telephone socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 217 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 218 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 219 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm) |
| 220 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 221 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 222 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep |
| 223 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair |
| 224 | Installation ,Testing and commissioning of ceiling fan, including wiring thedown rods of standard length (up to 30 cm) with 1.5 sq. mm FRLSH PVC insulated , copper conductor , single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc. as required |
| 225 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable |
| 226 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required. (for A.C. Point/MCB Point) |
| 227 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. |
| 228 | Supplying and fixing following way, single pole and neutral (SPN), sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way , Double door |
| 229 | Supplying and fixing following way, horizontal type three pole and neutral (TPN), sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door |
| 230 | Supplying and fixing following way, horizontal type three pole and neutral (TPN), sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door |
| 231 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door |
| 232 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 233 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 234 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A |
| 235 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A,30KA,FPMCCB |
| 236 | Supply and fixing of 40 Amp. TP MCB (10 KA) C Curve. |
| 237 | Supply and fixing of 63 Amp. TP MCB (10 KA) C Curve. |
| 238 | Supply and fixing of40 Amp. FP MCB (10 KA) C Curve. |
| 239 | Supply and fixing of 63 Amp. FP MCB (10 KA) C Curve. CAT A |
| 240 | Supplying and fixing following rating, four pole, (three phase and neutral) SPN, 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A |
| 241 | Supplying and fixing following rating, four pole, (three phase and neutral) SPN, 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 A |
| 242 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 243 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 244 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 245 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) |
| 246 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 247 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 248 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.100 mm width X 50 mm depth X 1.6 mm thickness |
| 249 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, inconvenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness |
| 250 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required.100 mm dia |
| 251 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 252 | Supply and fixing of LED Tube Light with Metal heavy duty Box type batten Light fitting 1X22 watt suitable for upto 1X22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. |
| 253 | Supply and fixing of 3 watt to 6 watt LED(spot light) fitting Confirming to IP 65 and above protection Complete in all respect. (Use as a Decorative Mirror Light) |
| 254 | Supply and fixing of 36 to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect |
| 255 | Aesthetically designed LED linear fixture suitable for suspended down type with housing made of high quality extruded aluminium alloy including die-cast aluminium end cap. These series are also available with seamless continuous lighting system ensuring no visible dark spot or light leakages(Philips/Havells/Panasonic) as per design approved by architect incharge |
| 256 | Providing and installation Aesthetically designed LED Pendant light15 W 4000K downlight with white /black powder coated polycarbonate housing and equiped with aluminium die-cast housing,(Philips/Havells/Panasonic) as per design approved by architect incharge |
| 257 | LED Track Light Leander-10W(Black,4000K) LED Track Lights(DL01-10083) |
| 258 | Uranus-1 Meter Black LED Track (TR01-10002) |
| 259 | Black LED Track straight connector (TR01-10006) |
| 260 | Track Suspension Kit(TR01-10013) |
| 261 | Supply and fixing of Mirror Light |
| 262 | Supply and fixing of Wall Light |
| 263 | Supply and fixing of Step Light |
| 264 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following size size 6 sq mm x 2 core |
| 265 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 10 sq mm x 4 core |
| 266 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 25 sq mm x 3-1/2core |
| 267 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 35 sq mm x 3-1/2core |
| 268 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 95 sq mm x 3-1/2core |
| 269 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 6 sq mm x 2 core |
| 270 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 10 sq mm x 4 core |
| 271 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 25 sq mm x 3-1/2core |
| 272 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 35 sq mm x 3-1/2core |
| 273 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 95 sq mm x 3-1/2core |
| 274 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 6 sq mm |
| 275 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 10 sq mm |
| 276 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 16 sq mm |
| 277 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 25 sq mm |
| 278 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 35 sq mm |
| 279 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 50 sq mm |
| 280 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 95 sq mm |
| 281 | Supply& Erracetionof factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreise Electrical control panel with TPN MCCB\"s (Four Pole 36 KA with thermal magnatic release) Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above insulated with heat shrink sleeving and mounted on non gyroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB\"s shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm.Cubicletype switchboard shall be of cat A & B Only. Cubicle TypeIncoming -200 Amp MCCB-1 No.Outgoing - 100 Amp 4P MCCB - 2 Nos. (for VTPN D.B. DB\"s)100 Amp 4P MCCB - 2 Nos. (for VTPN D.B. DB\"s)63 Amp 4P MCCB - 1 Nos. (for Terrace pump))40 Amp DP MCB - 2 Nos. (Spare) |
| 282 | Supply and Laying of 1800*900*12mm thick chequerd rubber matting of tested quality. complete in all respect. as per I.E. Rules. |
| 283 | Supply & fixing of 12 Watt LED Bulb - B22 / E27 (Colour Temp.- 6500K / Lumens - 900 lm) cool day light, Input Volts (AC 90V-260V), 3-Star rating suitable for Batten/Angle holder including making connection.Complete in all respect. |
| 284 | Supply & fixing of 225/300mm sweep ventilating (Light Duty) exhaust fan complete with Metallic Blade (Steel bird guard protector /Copper motor for high air suction performance /Capacitor etc.), Noise level : (45 - 50) dB, Power consumption : 45 W, Rated voltage : 230 V, Rated frequency : 50 Hz, Motor type : Normal Speed. Complete in all respect. |
| 285 | Supply & fixing of 400mm sweep wall mounted (Light Duty) fan complete with Plastic Blade & Pull Cord (Adjustable upward and downward tilt mechanism /motor /capacitor etc.) Oscillation degree - 90, Power consumption : 60 W, Rated voltage : 230 V, Rated frequency : 50 Hz, Speed : 1350 RPM. Complete in all respect. |
| 286 | Supply & Fixing of LAN socket outlet modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. Complete in all respect. |
| 287 | Supply and fixing of LED high bay light Fitting with mandatory driver set having die cast aluminium body and lenses suitable for 60 watt to 72 Watt. Confirming to IP65/66 protection having Company LOCO Engraved complete in all respect . |
| 288 | MECHANICAL VENTILATIONSITC of Sigma 6 Inline Fan , air flow 415 cmh, Ideal for Hot/Cold air Transfer, Energy Saving Long Life Ball Bearing Motor, Easy to Install, Strong Air Flow, Low noise level, High Static Pressure, Fully copper winding motor |
| 289 | SITCOf Sigma 8 Inline Fan , air flow 820 cmh - 910 cmh, Ideal for Hot/Cold air Transfer, Energy Saving Long Life Ball Bearing Motor, Easy to Install, Strong Air Flow, Low noise level, High Static Pressure, Fully copper winding motor |
| 290 | SITC of Zeta AW 8 , air flow 180 cmh , Diy high velocity exhaust fan with fitted back draft damper, Turbo cylinder fan blade design for powerful air-stream extraction, Square design exhaust fan with removable easy clean cover, Ultr Quiet Motor, Easy installation clamps to fit and secure fan into ceiling, 100 mm diameter side ducting for easy duct installation, Easy clean removable fascia, self ceiling exhaust damper to prevent drafts, complete with white |
| 291 | SUPPLY & INSTALLATION OF VENTILATION PIPE MAKE-PVC Pipe 160 mm |
| 292 | SUPPLY & INSTALLATION OF VENTILATION PIPE MAKE-PVC Pipe 110 mm |
| 293 | SUPPLY & INSTALLATION OF Alumunium PIPE MAKE-Aluminium pipe 110mm - 3 rmt |
| 294 | SUPPLY & INSTALLATION OF PVC ELBOW MAKE-ASTRALPVC Elbow 160 mm |
| 295 | SUPPLY & INSTALLATION OF PVC ELBOW MAKE-ASTRALPVC Elbow 110 mm |
| 296 | SUPPLY & INSTALLATION OF PVC ELBOW MAKE-ASTRALPVC Socket 160 mm |
| 297 | PVC Socket 110 mm |
| 298 | SUPPLY & INSTALLATION OF PVC REDUCER SOCKET MAKE-PVC Reducer Socket 200mm X 160mm |
| 299 | SUPPLY & INSTALLATION OF PVC REDUCER SOCKET MAKE-PVC Reducer Socket 110mm X 160mm |
| 300 | SUPPLY & INSTALLATION OF PVC TEE MAKE-ASTRALPVC Tee 110mm LW |
| 301 | SUPPLY & INSTALLATION OF PVC TEE MAKE-ASTRALPVC Tee 160mm LW |
| 302 | SUPPLY & INSTALLATION OF GRILL & DIFFUSERDiffuser RMD 6 |
| 303 | SUPPLY & INSTALLATION OF GRILL & DIFFUSERDiffuser RMD 4 |
| 304 | SUPPLY & INSTALLATION OF GRILL & DIFFUSERGrill FGS 6 |
| 305 | SUPPLY & INSTALLATION OF GRILL & DIFFUSERGrill FGS 4 |
| 306 | FIRE SYSTEMSupplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. |
| 307 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
| 308 | Supplying, installation, testing & commissioning of manual call box of MS Construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. |
| 309 | Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. |
| 310 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in MS box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. |
| 311 | Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.6 Zone |
| 312 | Fire Alarm Panel with Talk Back Syetm Arrangements :Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required.10 Zone panel for fire alarm system.250 Watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required - 2 Nos.(one to act as standby)Talk back master station with LED PTT (press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos. talk back unit -1 Set.Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc. complete as required -1 Set.Amplifier change over switch for inter changing amplifier -1 No. Monitor panel for loudspeaker complete with output selector, ON/OFF switch, fuse, visual indications etc. complete as required- 1 No.Gooseneck microphone with stand and ON/OFF switch- 1 No. Main ON/OFF switch, fuse indication lamps, DC and AC voltmeters & ammeters, terminal blocks etc. complete as required -1 Set.Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos. 12 volt, 60 AH Each sealed maintenance free batteries -1 Set. |
| 313 | Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. |
| 314 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. |
| 315 | Fire Pump Set :Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required : Terrace PumpHorizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-\"F\" insulation, conforming to IS-325.M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head |
| 316 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :80 mm dia |
| 317 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :100 mm dia |
| 318 | Supplying and fixing single headed Internal Hydrant Valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Stainless steel |
| 319 | Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :80 mm dia |
| 320 | Supplying, fixing, testing and commissioning of Butterfly Valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100 mm dia |
| 321 | Providing, installation, testing and commissioning of Non-Return Valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :80 mm dia |
| 322 | Providing, installation, testing and commissioning of Non-Return Valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100 mm dia |
| 323 | Providing, installation, testing and commissioning of stainless steel Y-Strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.100 mm dia |
| 324 | Supplying and fixing 63 mm dia, 15 m long RRL Hose Pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Stainless Steel (Grade 304) |
| 325 | Supplying and fixing First-Aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m |
| 326 | Supplying & fixing 63 mm dia gun metal short Branch Pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304) |
| 327 | Supplying and fixing of Fire Brigade Connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way - 100 mm dia M.S. Pipe |
| 328 | Supplying and fixing Air Vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. |
| 329 | Providing & fixing of Pressure Switch in M.S. pipe line including connection etc. as required. |
| 330 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 25 sq mm x 3-1/2core |
| 331 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 25 sq mm x 3-1/2core |
| 332 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 25 sq mm |
| 333 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 334 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 335 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 336 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 337 | Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 338 | Providing & fixing carbon steel Fire Man Axe with rubber insulated handle tested to 20000 volts. |
| 339 | Providing and Fixing of Self illuminated /Auto Glow Exit Signs printed on photo-luminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site. |
| 340 | Providing & fixing dial type (150 mm dia) Pressure Gauge with isolation ball valve suitable for working pressure of 250 PSI cost shall be of inclusive of providing any short pieces, nipples, elbows etc as required.having calibration of0-15 Kg/cm2. |
| 341 | Providing, fixing, testing & commissioning of resilient rubber lined single Arch Vibration Eliminators suitable for raw water up to 45oC temperature, working pressure 8.8 Kg/cm2 and test pressure 20 Kg/cm2 for :-100 mm dia |
| 342 | Providing & fixing cast iron air release valve of 25 mm dia including 25 mm dia Ball valve with fittings etc. as per the requirement. |
| 343 | Providing & Fixing of 1.6 mm thick M.S/Door Frame, Door capable of accommodating fire Hose Reel, Landing Valve, Hose Pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for makingRecessed type mansoary box (by civil contractor).1500x900 mm (Indoor Cabinet) Only Frame |
| 344 | Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :63 Amp, 35kA TPN MCCB, Ics=100% Icu, with Suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. -2 Sets |
| 345 | THEMED INTERIOR & ART WORKSWall Panelling: Fabricating & fixing full height plywood panelling (overall thickness 62mm) consisting of 50mm x 25mm x 2mm GI sections approved Make framework with all necessary reinforcements required of GI, at spacing not exceeding 600mm x 1200 . Partition framework to be fixed to existing masonry walls. Rate to include providing and fixing of additional GI sections of approved size as per Architects drawings. Cost to include additional sections (horizontal & Vertical) as required for fixing of Digital Displays, Screens.,, Glass boards, and White boards as indicated by the Architect. Cost to also include the necessary provisions required to take Data & Electrical conduiting.Boarding: Boarding with 12mm th Fire resistant pre laminated LDF Board LDF boardCost to include an average projection of 600mm from true wall including creating slopes, curves in elevations as indicated in the drawings.Cost to include providing of recess of upto 200 mm such as coves and niches, the shape shall be not measured seperatelyCost to include providing necessary BWP plywood backing up to 18mm for Digital displays as indicated in the drawingCost will be measured based on the board up area and not for frame works.Approved Brands - 1. Frame : Jindal, apollo, sections or equivalent2. Plywood - Green ply, Kitply, Merino, archidply or equivalent3. Laminate– Merino, Greenlam or equivalent |
| 346 | Fixed Furnitures: Providing and supply of custom built fixture with GIformwork made of 50 x 50mm section frameto base e. Frame spacing shall not exceed @ 600mm c/c one way and the framework cladded with first skin of 16mm thk ply. Or 19 mm block board for display cabinets The top skin shall be finished with laminate of approved shade and color, and/or matching lots, as per Architect\"s instructions,(if so required), on partitions, ceiling and paneling as perpattern and design as indicated on the drawings. Cost to be inclusive of All joint to be supported with frame or support members as specified by the Architect. Joints to be bonded with only \"joint Adhesive provided by the approved dupont vendor\"- as specified .Cost to be inclusive of any coving to be done for the panelling along the wall & ceiling and any stencil cuttingas per architect\"s detail drawing.Provision to be provided for lighting, electrical, data & AV wiring including conuting, equipment mounting etc., The contractor shall co-ordinate with other agencies to ensure seamless workflow including co-ordination with their services, finishes requrired etc., in correspondance with the project managerWhere ever applicable glass box will be constructed with 8mm th clear toughened glass fixed using UV glue / silicon carefully joined with in exemplinarry skill to perfect corners. The glass box will be placed on the podium with support from solid acrylic.Cost of light fixture excludedPlywood Make:Century, Greenply, Merino or other brand approved by the architectSolid Acrylic : Make: Hanex, Samsung Staron Glass Make : Saint Gobain Clear GlassProviding and Fabrication of Powder coated stucture with base like spec stand Polycarbonate / Corian printed graphic Translation Works - English text will be provided by the client. Hindi and Punjabi translation to be done. |
| 347 | Providing and Fabrication of Powder coated stucture with base like spec stand Polycarbonate / Corian printed graphic Translation Works - English text will be provided by the client. Hindi and Punjabi translation to be done. |
| 348 | Size : W2400 X D700 X H1000; Reception Table, Particle Board & MDF Top, Reception 2 (make Geeken/ Godrej/featherlite) customised as per Architect incharge |
| 349 | LOOSE FURNITUREMainpuri\"s City Gallery - Chairs/Custom designed benchesModel : Custom, featherlite, monarch Ergo, Ergo Designs |
| 350 | Culture & arts crafts - Chairs/Custom designed benchesModel : Custom, featherlite, monarch Ergo, Ergo Designs |
| 351 | Workstation in AV Room Size (6 x 2 x 2.5 ft) : Workstations made of Powder coated M.S structuer and Pre laminated LDF Board of 20mm th for table top and 16mm for sides complete with raceway / conduits for internal wiring etc., complete along with a storage unit of 450 x 450 x 450 mm with 2 drawers and 1 shutter. Make : Godrej Interio / Featherlie / Ergo / Custom/Equivalent |
| 352 | Closed storage units made of pre-laminated LDF boards with 2 shutters per stroage unit with box hinges of Ebco make and skirting rasied by 75 mm; Back Storage Unit, 18mm PLPB, Extruded Aluminium Profile; Evoke 4, W2250 X D450 X H2200 make Godrej / Featherlite / Monarch Ergo / Equivalent/Geenken or equivalent |
| 353 | Vinyl print with Installation - Providing & Fixing Printed Vinyl Graphics on Punned or Levelled Surface of (3M or Equivalent) ,overPlywood /MDF or Laminate. Cost to include cleaningfor any stains, scffolding for height upto 8000mm from FFLApproved Make - 3M, LG, Avery/Equivalent |
| 354 | Artefacts/Manuscripts DiplaySize : 24\" 0\" x 12\" 0\" |
| 355 | Supplying, designing, fabricating, transporting, hoisting and fixing in position mural works in good quality of 70 mm Red sandstone and 6-10mm powder coated MS sheet in various elements for all levels. Stone shall be free from cracks, lines stains and even in shade for each element. The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding, etching, buffing and polishing. The carving and molding work shall be of very good quality. The work to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, (to be paid separetely) dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architect in charge. |
| 356 | Design , supply and Installation of Glass chandelier Installation of size 72\"x30\"x36\" Oval Shaped . |
| 357 | Providing and Fixing Knauf Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 21mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound abMRbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.5. (Average value of AbMRption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm. SUSPENSION: The panel shall be downwardly installed with tongue and groove mechanism using Inside clip on Knauf Prelude 43 with 24 mm wide T - section flanges having rotary stitching on all T - sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm, 35mm and 30mm respectively. The deflection loading of the system shall be 17.8 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with deflection loading of 21.4kg/m. The end details of the main beam and cross tee shall be made of pre hardened steel and the cross tee is designed to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T - Sections shall be made of hot dipped galvanized steel of 100 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. Installation should be carried out as per Knauf recommended procedure. The grid shall be installed with suspension system of Knauf make.INSTALLATION: To comprise main runner spaced at 1200mm centre to centre securely fixed to the structural soffit using Knauf suspension system (specifications below) at 1200mm maximum centre. The First/Last Knauf suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be Knauf wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centre to centre.The panel shall be downwardly installed with tongue and groove mechanism using inside clip on grid. Panel shall be butt jointed in the shorter side using industrial/wood glue and expansion joint of 15mm to be kept at every 7.2m. Expansion joint can be finished using a transition profile. KNAUF SUSPENSION SYSTEM accesMRies manufactured and supplied by Knauf consisting of M6 Anchor Fasteners with hanger hole, pre–Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. Additionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners. |
| 358 | Providing and fixing of 12 mm th clear toughened glass panel fixed over Showcase it with all required hardware with holes and profile support as per the drawing. |
| 359 | Content & Application Development:i) Research--Complete and comprehensive research on the life, philosophy, beleifs and work of Sant Ravi Das Ji basedontheadvisorynote, included in the tender. The work will include butnot belimitedtoappointmentofexpert researchteam,travel,stay,food,meetings and consultation with subject experts, archival material identification, all consumables, printing, stationary, copies of films, drafts and preparation of a Content Document for submission to and approval by the Department and Architect in-charge approx.20 seconds per Exhibitii) Script & Translations--Developing and writingofanarrativescriptthatwouldbe writtenfromtheresearchedandapproved contentprovidedbytheclient.Scriptwould lend itself to narrative syncing the video, playedseparately.Scriptingrequiredintwo languages: Hindi and English. With Hindi being the source language. The translation could be outsourced to another person though it will be the responsibility of the selected scriptwriter. There would be some poetic and lyrical contentinthescript.Thescriptwritermust havepreviousexperienceinhavingwritten scriptsofcontemporary,historicalcontent. Qualityofscripttobesuperior,succinctly capturing the mood, vision and sense of mission of the protagonist, while also painting an appropriate picture of reality of the times. As approved by the Department and Architect in-chargeScriptmustdojusticetotheintentofthe museum.approx.20 seconds per Exhibitiii)ArchivalAcquisition--ofallnecessary Archival Material, photographs, films, letters, workingdrafts,diaries,manuscriptsand objects (specific toSant Ravi Das Ji & his beleifs, teachings and of related events in India & his native village) from various government and private sources, inclusive of rights to use for museum exhibit, includingediting,restoration,touchupand also partial use, if required. As approved by the Department and Architect in-charge approx.20 seconds per Exhibit |
| 360 | Placement of museum display objects at their appropriate location with required precision including necessary acrylic hooks, frames, nuts bolts, T & P etc. required for proper completion of the job as per the requirement of Museum norms and directions of Engineer in charge/ concerned authority. |
| 361 | Providing and fixing Canvan fabric used in most canvases are either linen or cotton. Of the two, linen is considered the best due to the quality of the surface and its durability, of printed graphics over canvas and mounted over a framework made solid Wood (items complete with all required hardware) |
| 362 | Providing and fixing frames of customized size Imperial Frames Stratford Artist Vintage Picture Frame for 3/4\" Thick Canvas, Museum Quality Wooden Antique Photo Frame |
| 363 | C.C.ROADEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 364 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 365 | Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications,cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. |
| 366 | Construction of granular sub-base by providing close graded Materia conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 |
| 367 | Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.Cement concrete prepared with batch mixing machine |
| 368 | Providing and fixing in position pre-moulded joint filler in expansion joints. |
| 369 | Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade ‘A’ sealing compound. |
| 370 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 371 | GRASS PAVEREarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 372 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 373 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 374 | Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge. |
| 375 | MURAL WALLEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 376 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 377 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 378 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 379 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from naturalsources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 380 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 381 | Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete |
| 382 | Centering and shuttering including strutting, propping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantilevers |
| 383 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 384 | Supplying, designing, fabricating, transporting, hoisting and fixing in position mural works in good quality of 70 mm Red sandstone, and 18mm marble insertion and 6-10mm powder coated MS sheet in various elements for all levels. Stone shall be free from cracks, lines stains and even in shade for each element. The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with different process of i.e carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding, etching, buffing and polishing. The carving and molding work shall be of very good quality. The work to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, (to be paid separetely) dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architect in charge. |
| 385 | COBBLE PATHWAYEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 386 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil |
| 387 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 388 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class - 150 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 389 | 15 mm cement plaster in 1:4 (1 cement : 4 coarse sand) finished rough with sponge. |
| 390 | Providing & fixing Cobble Stone Flooring (10X10X10)cm filling of joints in 1:3 Cement mortarwith matching colour pigments all complete specification & direction of Engineer in charge. |
| 391 | LANDSCAPETrenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). |
| 392 | Supplying and stacking of good earth at site including royalty but including carriage1km (earth measusred in stacks will be reduced by 20% for payment). |
| 393 | Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm |
| 394 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge.. |
| 395 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
| 396 | Rough dressing the trenched ground including breaking the clods. |
| 397 | Fine dressing the ground |
| 398 | Grassing with selection No.1 grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and the good earth shall be paid for separately). |
| 399 | Uprooting weeds from the trenched area after 10 to 15 days after flooding with water including disposal of uprooted vegetation. |
| 400 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in chargeWith grass Turf |
| 401 | Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. |
| 402 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 90 cm dia, and 90 cm deep |
| 403 | Preparation of beds for hedging and shrubbery by excavating 60 cmdeep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). |
| 404 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water) |
| 405 | Providing and stacking of Acacia auriculiformis of ht 150-165 cm in bag size of 25 cm as per direction of the officer-in-charge. |
| 406 | Providing and stacking of Adansonia digitata (kalp vricksh) of ht 150-165 cm in bag size of 25 cm as per direction of the officer-in-charge. |
| 407 | Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 408 | Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 409 | Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge |
| 410 | Providing and stacking of Fishtail palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big size HDPE bags as per direction of the officer-in-charge. |
| 411 | Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35 - 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. |
| 412 | Providing and stacking of Phoenix sylvestris Roxb. (Wild date palm/khajur)of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge. |
| 413 | Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge. |
| 414 | Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 415 | Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 416 | Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. |
| 417 | Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. |
| 418 | Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge. |
| 419 | Providing and stacking of Ficus benjamina (green) of height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of size 25 cm as per direction of the officer-in-charge. |
| 420 | Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer-in-charge.. |
| 421 | Providing and stacking of Ficus reginald well branched, bushy of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.. |
| 422 | Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushtyshape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. |
| 423 | Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 424 | Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-charge. |
| 425 | Providing and stacking of Asparagus sprengeri of height 15 cm to 20 cm, full of leafy branches in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.. |
| 426 | Providing and stacking of Ophiopogon jaburan ( variegated ), full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. |
| 427 | Providing and stacking of Washingtonia filifea palm stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-in-charge |
| 428 | Providing & fixing White/Colored River (Stone) Pebbles size of 1\" to 2\" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. |
| 429 | SEPTIC TANKEarth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. |
| 430 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.1.50 M TO 3.0 M |
| 431 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.3.00 M TO 4.50 M |
| 432 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 433 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, including the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 434 | Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform |
| 435 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 436 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 437 | Cement plaster (1:3) finished with a floating coat of neat cement.20 mm Cement Plaster |
| 438 | Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. |
| 439 | Providing and fixing C.I. tee at the inlet and outlet of septic tank. |
| 440 | Providing & fixing 75mm dia vent pipes. |
| 441 | Providing & fixing of 75mm dia cast iron terminal guard. |
| 442 | Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.HD . -20- Circular shape 500mm internal diameter |
| 443 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design.With F.P.S. bricks |
| 444 | EXTERNAL WATER SUPPLYProviding & fixing G.I. pipes complete with G.I. fittings includingtenching and refilling etc. (external work)40mm nominal bore. |
| 445 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40mm nominal bore. |
| 446 | Constructing brick masonry chamber 600 x 600x750mm insidewithF.P.S. brickwork in cement mortar 1:4 (1 cement : 4 coarse sand) for Sluice Valve / Air Valve, with C. I. surface box 100 mmtop diameter, 160 mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slabwith 1 : 2 : 4 mix (1 cement : 2 coarsesand : 4 gradestone aggregate 20 mm nominal size); necessary excavation,foundationconcrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plasteringwithcement mortar 1 : 3 (1 cement : 3 coarsesand ) 12mmthick finished with a floatingcoatofneat cementcomplete as per standarddesign With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 447 | STORMDRAINEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 448 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 449 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 450 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 451 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster |
| 452 | Fire Pump Set :Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : Jockey PumpHorizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS : 325.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 70 m Head |
| 453 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :65 mm dia |
| 454 | L.T. Switch Panel Board :Supply& Erracetionof factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreise Electrical control panel with TPN MCCB\"s (Four Pole 36 KA with thermal magnatic release) Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above insulated with heat shrink sleeving and mounted on non gyroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB\"s shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm.Cubicletype switchboard shall be of cat A & B Only.Lighting Panel :Incoming -100 Amp MCCB - 1 No.Outgoing - 63 Amp 4P MCCB - 2 No. 63 Amp 4P MCCB - 1 No. (for Spare) |
| 455 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. Following sizesize 25 sq mm x 3-1/2core |
| 456 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer-incharge. for cable size 25 sq mm x 3-1/2core |
| 457 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 25 sq mm |
| 458 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 459 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 460 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 461 | EXTERNAL ELECTRIFICATIONStreet Pole with LED Lamp :Supply of 4 Meter height Carley Square 40W LED in Extruded aluminium bottom pipe (grade 6063 with test certificate) Sq. 150 x 3mm thickness, extruded aluminium stem with inner ribbed Sq.30 x 2mm thickness, extruded aluminium top pipe with inner ribbed with Light Distribution 360°. Pre treated with silicone gaskets. PDC aluminium service door 330mm height x 75mm width at 335mm height above the base plate shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. For better lighting performance there is Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Lamp fixed is position. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >87%, power factor >0.95, IP65, THD <10%, Surge protection 5KV. LED Colour Temperature 3000K, 230-240Vac, CRI >80, MacAdam step> 3, Mechanical resistance IK08. MS mounting plate Sq. 250 x 12mm thick steel of grade E250 to IS 2062:2011 with 4 elongated holes 38 x 19 to suit M16 bolts at CC180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation pole. Hot dip galvanised foundation bolt. The pole should undergone Pure polyester powder coated process, Mild shot blasting. The product should be BIS and CE Certified. Make as per Klite KL-4663/Unilamp/Ligman. |
| 462 | supply and fixing following capacity of automatic street light cubicle control pannel with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 seeries with contactors, HRC fuse, isolating switch, metering instrument and instrument box with CTs etc.complete in all respect.40 A SPN |
| 463 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc.Following sizesize 6 sq mm x 2 core |
| 464 | Supplying and laying ofaluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed bythe Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc.Following sizesize 10 sq mm x 4 core |
| 465 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed, underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer -incharge.for cable size 6 sq mm x 2 core |
| 466 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed, underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earthas per direction of engineer -incharge.for cable size 10 sq mm x 4 core |
| 467 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cablesize 6 sq mm |
| 468 | Supply and fixing ofplain or pin type copper tin plated cable socket (lug) to cable leadsfor pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cable size 10 sq mm |
| 469 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 470 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 471 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 472 | Supply of Spike light luminaire LED 3000K/4000K/5700K 240Vac CRI >80 Mac-Adam step 3, Input power 6W having Dimension 101 x Ø90 x 330 mm, Beam Angle : 40° with Electronic driver ON/OFF. CE and BIS Certified. LUMINAIRE TYPE Spike Mounted luminaire. IP rating IP66. MATERIAL CHARACTERISTICS Die-Cast aluminium housing & Front ring (grade ADC12 with testcertificate). Surface mounting spike made of Polypropylene black. Silicone clear gasket. SS fasteners. Mechanical resistance IK06. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. LIGHTING PERFORMANCE Toughened Clear glass diffuser of 4mm thickness. This luminaire contains built-in LED modules. LED modules are engineered accordingly tothe existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40?C. Operating ambient temperature range is from -15?C to +50?C. Driver efficiency >84%, power factor >0.95, THD <10%, Surge protection 2.5KV. There may be changes in fixture selection and quantity as per architect intent. Make: K-Lite KL- 4265/Unilamp/Ligman |
| 473 | Supply of RADO MINI Wall light |
| 474 | Supply of Zedo Round Surface Mounting Light |
| 475 | Supply of SILL FAÇADE LIGHTING |
| 476 | Supply, Installation, Test in gand Commissioning of LEDRGB/RGBW flood lighting luminaire for facade lighting with Die- cast aluminium housing, powder- coated finish, of following wattage. Luminaire shall be capable of producing dynamic color changing light for with 16 million colors by DMX/ Ethernet based control. The be amangle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100-270 VAC, 50Hz with power factor>0.9. Fixture shall be suitable to operate at anambient temperature range of-10°Cto +50° C and shall be IP65 and IK06 rated. Life time shall be atleast L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS(IS10322) and shall be complete with all necessary accessories required for proper working of fixture in cluding weatherproof connection cables, waterproof connector setc. as required. 30 W |
| 477 | Supply of 3000K/4000K/5700K In-ground 8W asymmetrical luminaire made up of die-casting with Ø116 stainless steel 316 grade front ring with silicone black gasket and toughened clear glass diffuser. With Electronic Driver, The luminous flux of the luminaire is upto 550 lm for 3000K BA- 35°/45° (Asy). The ingress protection is IP67 and impact resistance of IK08. The luminaire is integrated with high power NICHIA LED with CRI=80, SDCM=3, L70/ B10 @ 60000 Hrs at L70B10. The integral constant current driver comes with the power factor greater than or equal to 0.9, total harmonic distortion less than 15% with operating efficiency greater than 80% and a surge protection of 3KV. The driver input voltage 240Vac at 50-60Hz, operating voltage of 100- 277Vac and operating temperature of -20° ~ +40°C with CE confirmed BIS approved. There may be changes in fixture selection and quantity as per architect intent Make: K-Lite KL-4098, Unilamp/ Ligman |
| 478 | Supply of 3000K/4000K, 230Vac, 3W Symmetrical Monocolour Stix Light made of Luminaire made of extrusion aluminium tube with Pure polyester powder coated finish for high durability having height 1162mm, Ø25mm and Non yellowing UV stabilized Clear Acrylic Rod with 200mm length for Illumination. Mounting spike arrangement should be available to facilitate easy soil installation at any desired location. Luminaire should be IP65. The Luminaire provided with one metre cable length and IP67 connector. Lighting Performance CRI >80 MacAdam step>3, Electronic driver ON/OFF (External driver), Lifespan of the luminaire >60,000 hours at 40°C. Operating ambient temperature range is from -25°C to +55°C. Driver efficiency >85%, Surge protection 2KV. Certification: CE Certified, Design Patented/Registered, ROHS compliant, BIS Certification for Luminaires. Make as per Klite KL-4554/Unilamp/Ligman, |
| 479 | Supply of Surface mounted spot light LED 3000K/4000K/5700K 240Vac CRI >80 MacAdam step 3 Input power : 10W Dimension Ø95 x 124 mm, Beam Angle : 40° without Electronic driver ON/OFF, LUMINAIRE TYPE : Wall Mounted luminaire. IP rating IP66. MATERIAL CHARACTERISTICS: Die-Cast aluminium housing & Front ring (grade ADC12 with test certificate). Surface mounting Bracket made of Polypropylene black. Silicone clear gasket. SS fasteners. Mechanical resistance IK06. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. LIGHTING PERFORMANCE: Toughened Clear glass diffuser of 4mm thickness. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40?C. Operating ambient temperature range is from -15?C to +50?C. Driver efficiency >84%, power factor >0.95, THD <15%, Surge protection 2.5KV. Make: K-Lite Model no.-KL-4245/Unilamp/Ligman |
| 480 | Supply of linear 3000K/4000K/5700K In-Ground Grazer 24Vdc CRI >90 MacAdam step 3 Input power : 12WLight Distribution should be Symmetrical Electronic driver ON/OFF (External driver) CE and BIS Approved. LUMINAIRE TYPE: Facade encapsulated3000K/4000K/5700K In-Ground Graze with IP67. MATERIAL CHARACTERISTICS should beHigh grade aluminium housing (grade 6063 with test certificate) with End cap, SS fasteners & Clip, Mechanical resistance IK07. LIGHTING PERFORMANCE:: Polyurethane Encapsulation clear diffuser. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum(TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, Surge protection 3KV. Including required accessories There may be changes in fixture selection and quantity as per architect intent Make Klite KL-3277,Unilamp/Ligman |
| 481 | Supply and fixing of Footlight Inground Luminare (One way/Two Way/Four Way) |
| 482 | Supply and fixing of Power Grazer - 32, Mono Light , 6W |
| 483 | Supply and fixing of LED Bollard robustly designed IP65/IK10 Bollard is easy to install with base plate(BCP150 LED /NWPSU 220-240V 7043)(K-litePhilips/Panasonic/Havells or Equivalent) |
| 484 | FILTRATION TANKExcavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.50 m and lead upto 30 m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto distance of 30m from the foundation trenches. (where machine can not reach/move). |
| 485 | Excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.50 m and lead upto 30 m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto distance of 30m from the foundation trenches. (where machine can not reach/move).Additional Lift 1.5 to 3.0 m |
| 486 | Excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.50 m and lead upto 30 m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto distance of 30m from the foundation trenches. (where machine can not reach/move).Additional Lift 3.0 to 4.5 m |
| 487 | Providing and laying Cement concrete 1:4:8 (1cement :4 coarse sand :8graded stone ballast 40 mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation. |
| 488 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 489 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 490 | Class-150 brick work in 1:6 cementand COARSE sandmortar in foundation and plinth including supply of all materials, labour tools and plants, etc. Required for proper completetion of the work. |
| 491 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 492 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.All types of soil400 mm dia |
| 493 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia |
| 494 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, onforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size dia |
| 495 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 496 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. |
| 497 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. |
| 498 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge. |
| 499 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in pproved laboratory, i/c disinfection of ubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per uirement and direction of Engineer-in-charge. |
| 500 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 501 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia |
| 502 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design.With 20x20 mm square bar |
| 503 | GULLY CHAMBERExcavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soilPipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. |
| 504 | Providing, laying and fixing PVC pipe confirming to IS make working pressure 6 kg/cm2including testing labour T&P and all complete. 160 mm diameter |
| 505 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round R.C.C pipes including bed concrete as per standard design : 150 mm diameter R.C.C pipe |
| 506 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 507 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 508 | SILTING CHAMBERExcavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.50 m and lead upto 30 m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto distance of 30m from the foundation trenches. (where machine can not reach/move). |
| 509 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 510 | Class-150 brick work in 1:6 cementand COARSE sandmortar in foundation and plinth including supply of all materials, labour tools and plants, etc. Required for proper completetion of the work. |
| 511 | 15 mm cement plaster finished with a floating coat of neat cement of mix: 1:3 (1 cement : 3 coarse sand) |
| 512 | Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 513 | Centering and shuttering including strutting, propping etc. and removal of form for Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 514 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 515 | TUBEWELL WITH BOARINGBoring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.300 mm dia |
| 516 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of requireddia, conforming to IS: 12818, including required hire and labour charges, fittings & accesDSRies etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia |
| 517 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accesDSRies etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm Nominal Size dia |
| 518 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading& sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 519 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compresDSR, running the compresDSR for required time till well is fully developed, measuring yield of well by \"V\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compresDSR, tools & accesDSRies etc., all as per requirement and direction of Engineer-in-charge. |
| 520 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm Dia |
| 521 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150 mm clamp |
| 522 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150 mm Dia |
| 523 | Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc.50 mm nominal size dia |
| 524 | Electric logging of bore hole |
| 525 | Supply and Installation of 1.5 HP Submersible pump set complete |
| 526 | Providing and fixing of storage type (pressurised type) electrichot water heater copper sheet container, 25 mm thickinsulation, stove enamelled M.S. jacket thermostatically controlled immersion heater with pilot neon lamp, suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect including testing etc. Capacity 25 Liters |
| 527 | M.S.GATESteel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 528 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 529 | BOUNDRY WALLEarth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil |
| 530 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 531 | Brick Work with common burnt clay ( non modular) bricks of class - 150 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 532 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from naturalsources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 533 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 534 | Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete |
| 535 | Centering and shuttering including strutting, propping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantilevers |
| 536 | Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts |
| 537 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 538 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 539 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 540 | Finishing walls with Putty approved brand and manufacture and of required shade on undacorated wall surface to give even shade over including curing and cost ofall material, labour, T&P etc. required for proper completion of work. |
| 541 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 542 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 543 | Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints. |
| 544 | Providing and fixing sheet covering over expansion joints with iron screws as per design.Aluminium fluted strips 3.15 mm thick.150 mm wide |
| 545 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 546 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 547 | SPLIT ACSupply & Installation of split direct expansion air conditioners suitable for operation on AC supply single phase 50Hz 230 V with hermetiaclly sealed compressor, with air colled condenser with DCinverter technology, motor capacitor and start run capacitors,relay and over load protection unit,with one indoor and outdoor unit wiil be plaved outside the room on the tessace to avoid noise including standard lenght of suitable size copper tubing covered with insulation tube ( High wall chorded/cordless) suitable capacity 3 Core sheathed /PVC copper cable and a operated wireless remote unit 1.5 TR. |
| 548 | Supply & installation testing commissioningof Voltage Stabilizer Complete in all respect. |
| 549 | Supply.installation testingandcommissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R 410A duly insulated with elastomeric nitrile rubber type tubular insulation of density 55+/- 10% Kg/m3 betweenindoor & outdoor units as per specifications.12.7 mm O.D. (Min. Wall Thickness- 0.80 mm. insulation -13 mm thick) |
| 550 | Supply.installation testingandcommissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R 410A duly insulated with elastomeric nitrile rubber type tubular insulation of density 55+/- 10% Kg/m3 betweenindoor & outdoor units as per specifications.6.4 mm O.D. (Min. Wall Thickness- 0.80 mm, insulation- 13 mm thick) |
| 551 | CENTAL ACSupply Installation Testing & Comissioning of Hitachi make Flexi split units energy efficient Twin Rotary Compressors with corded remote.A unique build, it epitomizes compactness and can replace 3 conventional system Outdoor unit with just one 7.5 Tr Outdoor unit& 2 conventional system Outdoor unit with just one 3 Tr / 4Tr / 5 Tr Outdoor unit .Individual circuit & compressor for each IDU unit.Which are operatable up to 52 degree C .High Effeciency Machines.Upto 4 TR 1 Phase Units ,5 TR & 7.5 TR Units 3 Phase.CONDENSER - 4.0TR HITACHI PAC CONCEALED (FSP) |
| 552 | CENTAL ACSupply Installation Testing & Comissioning of Hitachi make Flexi split units energy efficient Twin Rotary Compressors with corded remote.A unique build, it epitomizes compactness and can replace 3 conventional system Outdoor unit with just one 7.5 Tr Outdoor unit& 2 conventional system Outdoor unit with just one 3 Tr / 4Tr / 5 Tr Outdoor unit .Individual circuit & compressor for each IDU unit.Which are operatable up to 52 degree C .High Effeciency Machines.Upto 4 TR 1 Phase Units ,5 TR & 7.5 TR Units 3 Phase.CONDENSER - 5.0 TR HITACHI PAC CONCEALED (FSP) |
| 553 | CENTAL ACSupply Installation Testing & Comissioning of Hitachi make Flexi split units energy efficient Twin Rotary Compressors with corded remote.A unique build, it epitomizes compactness and can replace 3 conventional system Outdoor unit with just one 7.5 Tr Outdoor unit& 2 conventional system Outdoor unit with just one 3 Tr / 4Tr / 5 Tr Outdoor unit .Individual circuit & compressor for each IDU unit.Which are operatable up to 52 degree C .High Effeciency Machines.Upto 4 TR 1 Phase Units ,5 TR & 7.5 TR Units 3 Phase.CONDENSER - 7.5 TR HITACHI PAC CONCEALED (FSP) |
| 554 | SITC of Flexi Split Indoor Unit - ( FSP )EVAPORATOR - 2.5TR HITACHI COMPACT CASSETTE(FSP) - Panel size 3 FT X 3 FT |
| 555 | EVAPORATOR - 2.0 TR HITACHI COMPACT CASSETTE (FSP)- Panel size 2 FT X 2 FT |
| 556 | GAS TOPUP & COMMISSIONING OF SYSTEMFirst Starting of DUCTED / Fsp System including topping R410A gas per site requirments. |
| 557 | Supply installation testing and commissioning of Interconnectingrefrigerantpipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation betweeneach set ofindoor &outdoor units as perHITACHI STD. & specifications,all pipinginsidethe roomshallbe properlysupportedwithMShanger. 15.9 mm dia 19 mm thk. Insulation |
| 558 | Supply installation testing and commissioning of Interconnectingrefrigerantpipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation betweeneach set ofindoor &outdoor units as perHITACHI STD. & specifications,all pipinginsidethe roomshallbe properlysupportedwithMShanger.12.7 mm dia 13 mm thk. Insulation |
| 559 | Supply installation testing and commissioning of Interconnectingrefrigerantpipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation betweeneach set ofindoor &outdoor units as perHITACHI STD. & specifications,all pipinginsidethe roomshallbe properlysupportedwithMShanger.9.5 mm dia 13 mm thk. Insulation |
| 560 | Supply installation testing and commissioning of Interconnectingrefrigerantpipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation betweeneach set ofindoor &outdoor units as perHITACHI STD. & specifications,all pipinginsidethe roomshallbe properlysupportedwithMShanger.6.4 mm dia 13 mm thk. Insulation |
| 561 | Covering of Copper pipes NEAR Outdoor - OPTIONAL WITH EXTRA CHARGES |
| 562 | Providing and fixing rigid CPVC piping complete withfittings, supportsas per HITACHI STD.&specifications and duly Clamped. 25 mm dia |
| 563 | Providing and fixing rigid CPVC piping complete withfittings, supportsas per HITACHI STD.&specifications and duly Clamped. 32 mm dia |
| 564 | Providing and fixing rigid CPVC piping complete withfittings, supportsas per HITACHI STD.&specifications and duly Clamped. 40 mm diaDrain Hose Connector |
| 565 | supply & fixing of 4 c x 2.5 sqmm of Copper conductor cable for looping between indoor & outdoor DUCTED & FSP system - Make - RR Cabel , Polycab , EQUIVILANT |
| 566 | Minor Civil Work/ Wall cutting / Core Cutting - BY CIVIL CONTRACTOR |
| 567 | FURNITUREProviding and Supply Double Bed, Wooden Ply , PLPB Board, CRCA Pipe Frame , Powder Coated, PPCPShoes , Without Matress of size2040X1600X758 (Double BED) Design and approve as per architect incharge ( Geeken, Bernhardt , Godrej or Equivalent)HOSTEL 12 |
| 568 | Providing and Supply Three Seater Sofa, Wooden Frame , SS Pipe Leg Frame , Sear Back Leatherite Tapestrywith leatherette finish (STANLEY 3 ) design as per incharge of architect (MAKE - GeekenGS 335 , Bernhardt , Godrej or Equivalent) |
| 569 | Providing and Wardrobe with Mirror, Wooden Ply , PLPB Board, CRCA Pipe Frame , Powder Coated,size900x600x1965(Wardrobe with Mirror) Design and approve as per architect incharge ( Geeken, Bernhardt , Godrej or Equivalent)STORAGE 15 |
| 570 | Providing and Supply Two Seater Sofa, Wooden Frame , SS Pipe Leg Frame , Sear Back Leatherite Tapestrywith leatherette finish (HENLY 2 ) 1300X780X755 design as per incharge of architect (MAKE - GeekenGS 335 , Bernhardt , Godrej or Equivalent) |
| 571 | CAFETERIA+ ADMINProviding and Supply Café Table , SS Pipe Frame, PLPB Edge Banded Top (GC 9062) 1200X910X750as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 572 | Providing and Supply Café Table , SS Pipe Frame, PLPB Edge Banded Top (GC 9062) 1800X910X750as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 573 | Providing and Supply Café / Restrorent Chair ,Chome Plated Reducing Pipe Frame, Leatherite Tapestry Chrome Plated(GC 950)as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 574 | Providing and Supply Reception Table,Particle Board Top ,(RECEPTION 2) W2400 X D700 X H1000 as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 575 | Providing and Supply High Back Chair , pipe Chrome Arm ,Chrome plated pipe stand , leatherite Tapestry with Chrome plated Finish and Swivel tilt for Receptiondesign as per incharge of architect (MAKE - Geeken GS 335 , Bernhardt , Godrej or Equivalent) |
| 576 | Providing and Supply Wooden Storage and Partice Board of size ( 900x450x1200) (STORAGE 11) design as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 577 | Providing and Supply Visitor Chair, PP Arm, Chrome Plated Pipe Stand, Seat & Back Leatherite Tapestry(GV 621)as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 578 | DORMITORYProviding and SupplyBunk Bed, MS Powder Coated Frame, CRCA Sheet, without mattress (L 2060 X W 950 X H 2000) BUNK BED 2 |
| 579 | Providing and Supply Steel Personal Locker, 2 Locker, 1 Hanging Rod,Thickness 0.8mm (GMS 51) W380 X D450 X H1800 as per incharge of architect (MAKE - Geeken, Bernhardt , Godrej or Equivalent) |
| 580 | Providing, fabricating and fixing/ erection of 6mm SS plate backlitted at desired location as per approved drawing of \"CULTURAL CENTER\" or as verified by the Department,having Helvetica Font with 72mm size Also including cost of providing and fixing of fasteners complete in all respects as per Architect in charge |
| 581 | Providing, fabricating and fixing/ erection of 6mm SS plate backlitted at desired location as per approved drawing of \"CULTURAL CENTER\" or as verified by the Department, in Hindi with 60mm size. Also including cost of providing and fixing of fasteners complete in all respects as per Architect in charge |
| 582 | Providing and fixing 300X300powder coated 10-12mm MS Signage at desired locations with letters (in english, hindi and Braille) and illustrations - etched, through cut, infilled or painted as per the design approved from Architect in charge, also including the cost of design, fabrication and onsite installation with all the necessary accesMRies and equipments for fixing on any surfaceas per drawing and design approved from Architect in chargeEnglish: Helvetica Font with min. 16 sizeHindi: Krutidev Fontwith min. 16 size |
| 583 | Providing and fixing powder coated MS Signage at desired locations of approved size for UP tourism Logo and illustrations - etched, through cut, infilled or painted as per the design approved from Architect in charge, also including the cost of design, fabrication and onsite installation with all the necessary accesMRies and equipments for fixing on any surfaceas per drawing and design approved from Architect in charge |
| 584 | TOURIST FACILITYProviding & fixing ofRED SANDSTONE/MS BENCHsize (1200 mm length and 600 mm and height 450 mm) with including ornamentation/Engraving/Embossing foundation & support with all necessary T&P etc all complete as per design of direction in engineer/ Architect in charge. |
| 585 | Providing & fixing of SS Dustbin size 400Dia. And 900Height fixing on a foundation with base plate and wrapped with red sandstone from all sides of 75mm with all complete as per design of direction in engineer/ Architect in charge. |
| 586 | Providing and fixing StandAlone Signage in Sandstone/Marble/Granite of approved thickness with powder coated 6-8mm MS letters and illustration at desired locations with letters (in english, hindi and Braille)- etched, through cut, infilled or painted, also including the cost of design, fabrication and onsite installation with all the necessary accessories and equipments for fixing on any surface as per drawing and design approved from Architect in charge English: Helvetica Font with min. 36 size Hindi: Krutidev Fontwith min. 36 size |
| 587 | Specification of Y-Drinking Water(Receiving, storing, handling, shifting, installation, testing & commissioning ofWAE. AENON.45.CHA Pou Water Station C.A, RO Processing Capacity 25LPH, size: 466X580X1445, Watt; 220v/50Hz, Cooling 480w, Hot 450W, net weight 110kg, in material SS 304, with 3 tap: Cold 20 Ltr,Ambient-25Ltr including all accessories complete in all respect etc. (Make -WAE/Voltas or Equivalent)) |
| 588 | Providing, fabricating and fixing installation of artistically evolved and adaption of Neeb Karori Spiritual Center LOGO near front mural wall in metal/ stone, as per approved design and location by Architect in charge |
| 589 | Designing, engineering, fabricating, and finishing of parametrically evolved Neeb Karoori inspired abstract Installtion of 1500X2500mm height 2500mm with integrated lighting having self-sustaining structure supported at base, fabricated in 2.5mm Stainless Steel (304 Grade) Sheet, using Laser Cutting, bending, welding and parametric assembly of open joints, and mirror finishing with gold pigmented PU coating at desired location as per approved drawing to the complete satisfaction of Architect in charge. Also including the cost of providing and fixing/erection at site complete to the entire satisfaction of the Architect, complete in all respects. |
| 590 | Providing, supplying, designing, fabricating and fixing of signage and information board with Text and Illustrations as per approved location and drawings & design of Architect in chargeProviding and fixing 450X900 powder coated 10-12mm MS sheet and 25mm Corian Signage at desired locations with letters (in english, hindi and Braille) and illustrations - etched, through cut, infilled or painted, also including the cost of design, fabrication and onsite installation with all the necessary accesMRies and equipments for fixing on any surface as per drawing and design approved from Architect in charge English: Helvetica Font with min. 16 size Hindi: Krutidev Fontwith min. 16 size |
| 591 | SOUND SYSTEMSupply, Installation, testing and commissioining of Full range wall mount loudspeakerwith1 x 4.5\" driverin a ported enclosure; Frequency Response : 80Hz-17kHz; Nominal Dispersion :125°H x 125°V; Power handling capacity : 40W; Nominal Impedance : 8O or 70/100V; Max SPL :103dB; Sensitivity :87dB; Installation : Indoor and Outdoor. Model DS 40SE Make Bose/ L-Acoustic/ D&B |
| 592 | Supply, Installation, testing and commissioining of Integrated zone amplifier having 6 inputs : 2 balanced and 2 unbalanced line inputs, 1 balanced page input and 1 balanced direct input; Frequency response : 55Hz-20kHz; Power : 2 x 120W @ 70/100V; Total harmonic distortion (THD+N) : = 0.3%; Dynamic Range : 88dB. Model: IZA 2120 HZ, Make: Bose/ L-Acoustic/ Powersoft |
| 593 | Supply, Installation, Testing and Comissioning of CD/DVD Player with USB Input. Model: CDMP 1500 Make Sony/ Philips/ Gemini/ Tascam |
| 594 | Supply and laying of 2 core 2.5 sqmm Armoured loudspeaker cable. Make: Klotz / Beldon / Krystal |
| 595 | Supply and fixing ofUL listed Connectors & Patch Cables/Connectors for interconnection of all equipments.Make: Neutrik / Amphenol |
| 596 | Supply, Installation, Testing and Comissioning of 15U Equipment Rack for housing all rack mountable equipments with front glass door; heat dessipation fans; internal lights; movement wheels, power distribution units etc. complete with standard accessories. |
| 597 | Supply, Installation, testing and commissioining of In Ground loudspeaker with frequency response of 70Hz to 10kHz; Nominal dispersion of 360H X 50V; Sensitivity of 87 dB SPL; Max SPL of 100 dB SPL; Long term power handling is of 80W@ 4 Ohm; Transformer taping can be done; Enclosed in a glass- reinforced polypropylene textured; Environmental Outdoor per IEC 529 IP35. Model: 360P Series II Make: Bose/RCF/ Equivalent |
| 598 | Supply, Installation, testing and commissioining of 6 channel mixing console of 2 mono inputs&2 stereo line inputs; Frequency Response : 10Hz-55kHz; Total Harmonic Distortion (THD+N) : 0.03% ; Power supply : External ; Phantom power : +48V ; Power consumption : 17W. Make: RCF/Allen&Heath/ Yamaha |
| 599 | Supply, Installation, Testing and Comissioning of Gooseneck Microphone with table top on/off switch : Cardioid polar pattern; Frequency Response: 50 Hz to 20 kHz; Impedance <100 Ohms; Max Sound Pressure level: 130 dB; RF shielding against intermodulation from wireless devices with MAT 133-S: a table stand with microphone modes like Toggle on/off, Push to mute, Push to talk. Model: MEG 14-40 + MAT 133S-B Make: Beyerdynamics/ Shure / Sennheiser |
| 600 | Supply, Installation, Testing and Comissioning of CD/DVD Player with USB Inputcomplete with standard accessoriesas per the tender specifications. Make: Sony/Philips/Gemini/Tascam |
| 601 | Supply and laying of 2 core 2.5 sqmm Armoured loudspeaker cable.Make: Klotz / Beldon / Krystal |
| 602 | Supply and laying of 2 core shielded PVC insulated Cu conduction microphone cable. Make: Klotz / Beldon / Krysta |
| 603 | Supply and fixing ofUL listed Connectors & Patch Cables/Connectors for interconnection of all equipments. Make: Neutrik / Amphenol |
| 604 | Supply, Installation, Testing and Comissioning of 9U Equipment Rack for housing all rack mountable equipments with front glass door; heat dessipation fans; internal lights; movement wheels, power distribution units etc. complete with standard accessories. |
| 605 | Supply& Installation of WiFiHotspot at various location with controllerbased etc all complete in dircection of engineer in charge. |
| 606 | DG SetSupply, Installation, Testing & Commissioning of 03 phase volts 50 cycle per second 1500 RPM air cooled, diesel generating set complete with silent type DG canopy & limiting sound level to 75 dB (A) over a distance of one meter with engine, alternator aircooled. The engine shall be complete with flywheel to suit flexible coupling with guard, air cleaner, fuel pump, fuel day tank, variable speed governor, fuel filter, lube oil filter, battery charging generator, voltage regulator, 24 volt charged voltage regulator, capacity and instrument panel comparing switch with key, space heater, lube oil temperature gauge, lube oil pressure gauge, water temperature gauge, battery charging ammeter, safety control for low lube oil pressure and hightemperaturetrippinDG Set with AMF Control Panel 63 KVA |
| 607 | G.S.T Extra as per applicable |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
