tender for Under Kanh River Rejuvenation, Development Work From Nagar Nigam Square To Ahilya Aashram. , Estimated Cost for Development & Protection of Saraswati River From Nagar Nigam Square to Ahilya Aashram, Indore, Earth work - Earth work in excavation for foundation, trenches for pipes / cables or drains etc. by mechanical means / manual means (exceeding 30cm in depth.) including ramming of bottom, dressing of sides, disposal of excavated earth including of all lift and lead upto 50m. Disposed earth to be levelled and neatly dressed oil, In or under foul position, including pumping out water as required.(Excavation, where sewage, sewage gases or foul conditions are met with from any source, shall fall in this category. Decision of the. Engineer-in-Charge whether the work is in foul position or not shall be final.), Filling by available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m., Transportation By Mechanical means including loading, unloading and stacking where ever necessary, Supplying and filling in plinth under floors including, watering, ramming consolidating and dressing complete., Moorum / Hard Copra, Construction of granular sub-base by providing Coarse graded material (CBR>30), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at OMC and compacting with vibratory roller of 80 100 KN Static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400., Supplying and filling in plinth under floors including, watering, ramming consolidating and dressing complete., crusher stone dust, plain cement concrete - Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level. Cement concrete grade M-10 (Nominal Mix) with 20 mm maximum size of stone aggregate, Reinforced Cement Concrete - Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate, Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.above plinth level and up to floor two level excluding cost of centering, shuttering and reinforcement etc., Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate, Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor two level excluding the cost of centering, shuttering and reinforcement with Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate., Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding upto floor level including cost of binding wire, wastage and over laps upto 12mm horizontal/ inclined position of reinforcement bars in slab and beams, plinth, chajjas, lintels, upto 4.5m vertical length of reinforcement in wall columns (over laps shall be provided as per requirement of IS : 13920; IS 456 & SP : 34) etc. complete. - Hot Rolled Deformed Bars, Formwork - Centering and shuttering including strutting, propping stretching etc. complete for and removal of form work by sheet plate or ply wood shuttering for : Foundations, footings, bases of columns, etc, for mass concrete. Centering and shuttering including strutting, propping stretching etc. complete for and removal of form work by sheet plate or ply wood shuttering for : Lintels, beams, plinth beams, girders, bressumers and cantilevers, Centering and shuttering including strutting, propping stretching etc. complete for and removal of form work by sheet plate or ply wood shuttering for : Columns, Pillars, Piers, Abutments, Posts and Struts, Centering and shuttering including strutting, propping stretching etc. complete for and removal of form work by sheet plate or ply wood shuttering for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc, brick work - Brick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894- 2002, class designation 50 (average compressive strength) upto plinth level : Cement mortar 1:4 (1 cement : 4 coarse sand), Brick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894- 2002, class designation 50 (average compressive strength) in superstructure above plinth level up to floor 2 level including the cost of scaffolding :Cement mortar 1:4 (1 cement : 4 coarse sand), pile work - Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length in M 20 cement concrete, excluding the cost of steel reinforcement but including the cost of boring, cement concrete, all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia Deduct for casing pipe and bentonite solution in 16.3 300 mm dia piles, Steel work - Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works., Providing and supply of Cast Iron Sluice Gate Square type as per IS-13349 duly tested inclusive of all taxes related to central, state and municipal, inclusive of excise duty, inspection charges, transpotation charges, transit insuranse, loading/ unloading and stacking at site/ store etc, complete. Sluice Gate Square type as per IS 13349, Size 900X900 mm. Cast Iron Wall Thimble mounted,Manually operated, cl-pl 5.50 meter, class-I, flush bottom closure, Providing and supply of Cast Iron Sluice Gate Square type as per IS-13349 duly tested inclusive of all taxes related to central, state and municipal, inclusive of excise duty, inspection charges, transpotation charges, transit insuranse, loading/ unloading and stacking at site/ store etc, complete. Sluice Gate Square type as per IS 13349, Size 1200X1200 mm. Cast Iron Wall Thimble mounted,Manually operated , cl-pl 5.5 meter, class-I, flush bottom closure, roofing work - Supply & installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineerin- charge) 0.50 mm ±5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 meter or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tappingscrews of size (5.5x 55mm) with EPDM seal or with polymer coatedJ or L hooks, bolts and nuts 8mm diameter with bitumen and G.I.limpet washers or with G.I. limpet washers filled with white leadcomplete upto any pitch in horizontal/vertical or curved surfacesexcluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required., Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G. seam bolts and nuts, G.I. plain and bitumen washers complete, Ridges plain (500-600mm), flooring work - Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade reflective type rubber modulded glossy colour paving block made by block making machine with strong vibratory compaction and of approved size and shape laid in required colour and pattern over and including 50mm thick compacted bed of stone dust/sand filling the joints with sand etc. all complete as per the direction of Engineer in charge including locking edges wherever required with cement concrete M15 grade or cement mortor 1:3 with pigment of required shade to match the colour /shade of block including cost of labour, material , etc. all complete., Providing and laying vitrified floor tiles (without soluble salt) or printed (with soluble salt) Nano polished (Glossy finish) in different sizes with water absorption less than 0.05% and conforming to IS : 15622 of approved make in all colours & shades, Ist quality/ premium quality in skirting laid on 12mm thick cement mortar 1:4 (1 cement : 4 sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness as per manufacturer specification)., stone work - Providing and fixing 16mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels, Granite of any colour and shade Area of slab over 0.50 sqm., Extra for providing full edge moulding to 16mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge., Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens (Karries and battens to be paid separately) including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : Red sand stone slab (40 to 50mm thick), Finishing Work - Finishing wall with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat pplied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture, RIVER TRAINING AND PROTECTION WORKS - Providing and laying gabion structures for erosion control, river training works and protection works with wire crates of size 2 m x 1 m x 0.3 m each divided into 1m compartments by cross netting, made from 4 mm galvanised steel wire @ 32 kg per 10 sqm having minimum tensile strength of 300 Mpa conforming to IS:280 and galvanizing coating conforming to IS:4826, woven into mesh with double twist, mesh size not exceeding 100 mm x 100 mm, filled with boulders with least dimension of 200 mm, all loose ends to be securely tied with 4 mm galvanised steel wire.) and as per specification in section 2500. - Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications and as per relevant clauses of section 2500., Stone/Boulder (min. wt. - 40 Kg), road work - Excavation for roadway in soil by manual means including loading in tippers and disposal with all lifts and lead upto 1000 meters and as per relevant clauses of section-300, Transportation By Mechanical means including loading, unloading and stacking where ever necessaryExcavated Earth 5 km or Part thereof, Construction of granular sub-base by providing Coarse graded material (CBR>30), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at OMC and compacting with vibratory roller of 80 100 KN Static weight to achieve the desired density, complete in all respect as per relevant clauses of section-400.Deduction for item No.4.1 to 4.5 and 4.7 if vibratory roller / motor grader is not used. i) If static roller is used in place of vibratory roller. ii) If mortar grader is not used, Providing and laying Cement Concrete grade M-10 Nominal mix 1:3:6 with 40 mm graded crushed stone aggregate, spreading the concrete by shovels mixing shall be in mechanical mixer, compacting by use of pin/plate/screed vibrators including form work by strong steel girders fixed by spikes., Construction of dowel jointed, plain cement concrete pavement in M-30 grade concrete over a prepared sub base with 43 or higher grade cement, coarse and fine aggregate conforming to IS:383 maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver with spreading the concrete by shovels, rakes compacted using needle, screed and plate vibrator and finished in a continuous operation including provision of contraction, expansion, and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, placing of dowel bar,tie rod admixtures as approved, curing compound, finishing to lines and grades as per approved drawings as per IRC-15 2011 and as per relevant clauses of section-602 of specifications complete excluding cost of steel in dowel ber & tie rod etc. Deduct from Item No.6.2, 6.3 and 6.6 above if paver with electronic sensor is not used and laying, compaction is done by any other method (Note:-The acceptance criteria regarding level, thickness,surface regularity,texturefinish,strength of concrete and all other quality control measures shall be the same as in case of machine laid work.) This item is to be executed with Prior written permission of Engineer-in-charge, Add extra in Item No.- 6.2 & 6.3 above for the cost of steel in dowel bar and tie bar etc. required as per design.Mild Steel dowel bars confirming to IS 432, grade I, Add extra in Item No.- 6.2 & 6.3 above for the cost of steel in dowel bar and tie bar etc. required as per design.HYSD tie bars of Fe 500 grade confirming to IS 1786,, NON SOR ITEM - Providing and fixing the Fabrication of 4 mm thick MS Sheet with CNC Cutwork including labor and material. Complete work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer. Complete work as per approved design by Architect and Engineer in charge, Supplying and fixing of Decorative MS pipe + Wooden sitting bench. All pipe first quality MIG welding machine after all joints & corner best grinding finish, sitting wooden width 70 mm & length 600 mm, thickness 20 mm with glossy polish (Touch wood) finish. Branded pipe shall be used like Apollo and Prakash surya ISI etc. (ISO 9001:2015 Certified company No.- AIPW12118/Q948. Spray paint first layer base epoxy primer & top coat black PU paint finish shall be used.Complete work as per approved design by Architect and Engineer in charge., Beautification and art work through different type of artistic, heritage, graffiti, 3D, mandana etc painting work. (a) Providing and applying acrylic premium exterior paint with silicon additive required shade for smooth and proper colour shade. (b) Painting with deluxe multi surface paint to give an even shade with approved oil paint and enamal based. preparing design and painting work of prior approved design on the prepared wall with the complete satisfaction of authority. (Rates are inclusive of all labours tools and plant/ material/ transportation/ scaffolding and all type of taxes except GST)Beautification and art work through different type of artistic, heritage, graffiti, 3D, mandana etc painting work. (a) Providing and applying acrylic premium exterior paint with silicon additive required shade for smooth and proper colour shade. (b) Painting with deluxe multi surface paint to give an even shade with approved oil paint and enamal based. preparing design and painting work of prior approved design on the prepared wall with the complete satisfaction of authority. (Rates are inclusive of all labours tools and plant/ material/ transportation/ scaffolding and all type of taxes except GST) Complete work as per approved design by Architect and Engineer in charge, Providing and laying 500x500x40mm thick Turf paver on 150mm thick sub grade of compacted bed of 20mm nominal size stone aggregate and base course with 50mm thick sand and filling joints with sand including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge., FABRIC CORTEN STEEL MURAL WALL GRADE A 1. Natural Rusting & Natural Color Changing in coming years treatment to be done. 2. Branded Sheets shall be used like- TATA, JSW and UTTAM. 3. Mural Wall will consist of only laser cutting CNC design & 3D CNC cutting of elements as per approved from Architect and Engineer in charge Plazma cutting will not be used. 4. The panel shall have provision of bolting to the support structure. 5. Corten steel sheets executed shall be deactivated before execution on site to avoid any further internal rusting of sheet. 6. Thickness of sheet to be used in 4 mm as per design approved from the Architect Engineer in charge Complete work as per approved design by Architect and Engineer in charge., Providing and fixing Aluminium Profile letters A Grade GOQ Brand LED module light with 6 mm first grade Astari brand exterior acrylic sheet with 5 mm ACP back pack tray sealed with silicon/araldite. Connection with 2 mm finolex/polycab wire and Union brand 400W power supply. (Rates are inclusive of all labours tools and plant/ material/ transportation/ scaffolding and all type of taxes except GST) . Complete work as per approved design by Architect and Engineer in charge., Supply and fixing of recessed ground mounted deep LED uplighter fixture with Honeycomb Louver. protected Uno PATHFINDER IP66 2700K-5500K 8deg-24deg as required. stainless steel body hard anodized aluminium finishes stainless steel & IK rating 08. Installation housing box power supply cables35 cm NS20N PCP 2x0,5 mm2 power supply 24V DC power consumption max 9 Watt lumen output 240-680lm working temperature-20°C +45°C IP rating IP66 (not for permanent immersion) insulation class III Weight upto 500gm. and delivers 90CRI for excellent colour rendering, and with binning-free LEDs carefully selected from two-step Macadams ellipse. PATHFINDER is smart shield protected against polarity inversion, an integrated super fast diode prevents accidental damage to the luminaire during installation on due to reverse polarity. Smart shield protects against hot-plugging. Fully integrated spike-reduce on protects the constant- current driver and prevents damage to the LED die surface. With housing box included and LED driver in IP66 casing box included., 3W recess deep uplight, Supplying, fixing & testing of approved make Power supply for recess light Supply and fixing of IP 65 surface ground mounted luminary fitted with 700ma 11W LED bollard with 8deg-24deg 3000K-4000K CRI80+ nondimmable LED power supply built in Color tolerance make -wipro,Phillips, Supplying and laying of approved make HDPE pipe as per IS:4984 and IS:14333 with latest amendment for installation of submersible pump with necessary connection, socket/couplings, tees, etc. as required (PE-63 & working pressure 6 kgf/sq cm) 25 mm Outer Dia., Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. 25 mm Outer Dia., Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel (ACP) Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis and design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades.The aluminium composite panel cladding sheet shall be coil coated, with kynar 500 based PVDF / fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material and labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. upto two decimal places., 4 mm thick alumminium composite pannel material consisting of 3 mm thick FR grade mineral core sandwiched between two alumminium sheets (each 0.5mm thick), Multi Color Stone cladding Providing and fixing stone cladding in substructure & super structure upto all levels in epoxy & water based chemical adhesive. Including labour, transportation, scaffolding, centering, shuttering & pointing with epoxy & water based chemical adhesive with an admixture of pigment matching adjoining stone/design/pattern. The front face pattern shall be mixture of multicolor different shape, size & variety of cultured stones used in wall cladding. The stone cladding may be in various shape style size and colors as per the design requirements. Complete work as per instruction of engineer in charge and consultant., Engraving/Embossing in Any kind of stone Providing and fixing of stone with Engraving/Embossing in any kind of stone having variable thickness of stone as per requirement of upto 100 mm & engraving/Embossing thickness of upto 25 mm with CNC/ water cutting machine or hand crafting . Fixing of the stone with epoxy & water based chemical adhesive etc. Complete work including providing fixing stone, labour, transportation, scaffolding, centering, shuttering, and pointing with epoxy & water based chemical adhesive with admixture of pigment matching adjoining stone/design/pattern. Complete work as per instruction of engineer in charge & consultant., Providing and laying Hand dressed cobble stone flooring of size 150x150x150mm (average) over 20 mm ( average) thick base of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry including pointing in white cement mixed with pigment of matching shade complete., Joints between stones should be less than 12 mm. pattern & design as per architectural drawing. -, Sterilizing treatment using Biocide: Masonry covered with algae, lichen, mosses, small plants, etc should be removed with knife blades, spatula and stiff bristle or soft wire brushes. Spray diluted solution of quaternary ammonium based biocide on surface of the masonry with out allowing to spray drift. Leave the treated area for atleast one week than brush off as much dead growth as possible. Next again spray a solution of aproprietary biocide and incorporating tribute tin oxide in same manner and clean the surface. - For height or width of item up to 20 cm. (Work measured & paid in RMt), Fabrication, supply, installation of Decorative Ornamental type highly purified cast iron Gates and Grills as per architectural design complete with red oxide Primer coat, painting with silver/ golden metallic colors and any required color, as per approved design by consultant / Engineer in charge (payment will be made as per weight of the complete unit), Design, supply and installing, Tensile fabric Structure Entrance Gate with MS Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses/space frame etc., including cutting, shaping, framing, hoisting, fabricating, and fixing in position and applying a priming coat of approved steel primer and tow coats of enamel providing and fixing PVC coated Tensile Fabric , both side PVDF , having not less than 750 gsm weight and 280 daN/5cm tensile strength(warp/weft) of Ferrari or equivalent brand, using Galvanised steel wire ropes with Threaded Stud End termination, fish plates and other required accessories. Fabric plotting on CNC plotting machine only. HF welding with miniumum 40 mm wide seams.
