Annapurna Lis- Emergency Repairs To Pumps& Motors Control Panel And Supply Of Electro Mechanical Consumables For Annapurna Lift Irrigation Scheme Located On Paleru River Near Chimiryala Village Kodad Mandal Of Suryapet District-1.00 Disassembling of burnt 25 HP, 3-Phase induction motor and rewinding to stator with new HTP make super enamled copper wire, providing new insulation materials, varnishing, heating up to obtaining of required IR values, hot air blowing, replacement of damaged bearings, bearing settings, assembling the motor, erection on base plate correct alignment of pump and motor, trail run at site including cost of all materials, labour charges, transportation charges of motor from scheme to work shop and work shop to scheme after rewinding and all other incidental charges etc, complete finished item of work as directed by the Engineer-in-Charge. 1.00 Disassembling of 5 HP Vaccum motor-pump set, Overhauling & Servicing to motor-pump including replacement of damaged items if any i.e., pump bearings-2 nos (6306-zz), pump shaft, gun metal bushes, pump glands, other defective items and assembling of pump, erection on base plate, testing, alignment of motor-pump set, trail run at site and all other incidental charges etc, Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 3 Pole Power Contactors MNX50, Make: L&T or other equivalent, on existing control panel board including wiring, commissioning, etc., Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 3 Pole Power Contactors MNX32, Make: L&T or other equivalent, on existing control panel board including wiring, commissioning, etc., Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of L&T Front Mounting Add-on auxilary Contact Block (1 NO + 1 NC) to L&T MNX 32A 3 Pole 240 VAC Power Contactor Make: L&T or other equivalent, on existing panel board including wiring commissioning, etc., complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 100A rated capacity HN size 00 Fuse links suitable for Type FN 100/125/160 Makes : L & T / C & S / Standard / HPL / Havells / Siemens / Indo Asian.Complete for finished item of work as directed by the Engineer-in-Charge. 2.00 Supply, Transportation and fixing of following MS threaded Flanges 2 Nos with nuts and bolts including cost and conveyance of all materials, taxes etc., complete. for 65mm dia MS flanges set (2 Nos) 165mm dia OD, 12mm thick each flange with required dia bolts and nuts Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 11 KV/22 KV Hand gloves Complete for finished item of work as directed by the Engineer-in-Charge. 15.00 Supply of Grease Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply and erection of LT current transformer with bar primary 100/5A to 1000 / 5A ratio in the existing panel including connections etc., complete. MAKE : KAPPA. Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 6-32A SP MCB,10KA, C/D Curve ISI Mark. Makes : ABB / Havells / HPL(Techno) /Hager / Indo Asian (Gold Plus) / C&S /Delton / Honeywell sentry / Benlo. Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Supply of 6-32A TP MCB,10KA, C/D Curve ISI Mark. Makes : ABB / Havells / HPL(Techno) /Hager / Indo Asian (Gold Plus) / C&S /Delton / Honeywell sentry / Benlo. Complete for finished item of work as directed by the Engineer-in-Charge. 3.00 Carryout routine maintenance and servicing of LT.Cubical pannel board having approximately 15 to 22 Nos of switches cleaning with power brower and servicing the contacts, tightning the connection of incoming and outgoing cables, and clicking the operating machanism for smooth functioning of switches and putting them in smooth working condition Complete for finished item of work as directed by the Engineer-in-Charge. 10.00 Supply of Diesel, Complete for finished item of work as directed by the Engineer-in-Charge. 20.00 Supply of G.I Bolts / Nuts and Washers, Complete for finished item of work as directed by the Engineer-in-Charge. 10.00 Cost of M.S Flanges including cost of bolts, nuts, rubber packing etc., complete and flange thickness conforming to IS:7322-1985 and flange dimensions conforming to IS:1538-1993 excluding cost of MS specials including cost and conveyance to site etc., complete. 300 mm diax 15 mm thick, Complete for finished item of work as directed by the Engineer-in-Charge. 1823.70 Supply & Fixing of 300 MM dia. MS Pipe for suction pipe, Complete for finished item of work as directed by the Engineer-in-Charge. 2.00 Supply and transportation of 90 W +/-10% (>=9000 Lumens) LED Flood light Luminaire made of pressure die cast aluminum housing with powder coated, having toughened glass cover, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66 )protected, wide operating voltage range , P.F > 0.90, System having efficacy >110 lumens/watt, with Ingress protection IP66, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>70, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with 5 years warranty. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates. LUMINAIRE MAKE : PHILIPS / OSRAM / GE/Venture / CROMPTON / BAJAJ / Surya /Wipro / Jaquar / Eveready / Halonix /Keselec / HAVELLS / POLYCAB / SURYA /SYSKA./ Capart / Fortune Arrt / FIEM /Arraystorm / GM / Goldmedal / Panasonic / Silicon / Leksa / Orient / HPL /Valmont / Transrail LED MAKE : PHILIPS LUMILEDS / CREE /NICHIA / OSRAM / SAMSUNG / LG LEDs, Complete for finished item of work as directed by the Engineer-in-Charge. 16.00 Supply of 9.1 Mtr PSCC Pole 280 Kg Working load, Complete for finished item of work as directed by the Engineer-in-Charge. 1.50 Supply of 7/3.15 AAA C all Alluminium annealed conductor Rabit, Complete for finished item of work as directed by the Engineer-in-Charge. 45.00 Supply and erecting porcelain pin/shackle type insulator suitable for L.T, Complete for finished item of work as directed by the Engineer-in-Charge. 15.00 Supply of 40 mm x 40 mm x 6 mm angle iron with I bolt, Complete for finished item of work as directed by the Engineer-in-Charge. 16.00 Earth work excacvation for all soils for Pole Pit for 7 to 11 Mtrs Pole, Complete for finished item of work as directed by the Engineer-in-Charge.
