|
| 1 | C.S Coupling Having Material As per IS:1030 Grade 280-520W For mill Size 30\"x60\" as per Drg. Supply Basis |
| 2 | Conversion Basis |
| 3 | Machining Charge |
| 4 | Cast Steel Crown Pinion Having Material IS:2708 Grade-III-B For Mill Size 30\"x 60\" as Per Drg.Supply Basis |
| 5 | Conversion Basis |
| 6 | Machining Charge |
| 7 | C.S.Trash Plate Having Material As per IS:1030 And Grade-III-B Supply Basis |
| 8 | Conversion Basis |
| 9 | Machining Charge |
| 10 | Teeth Cutting/Grooving of Trash Plate As Per Drg. |
| 11 | C.S.Trash Beam As per IS-1030/IS 2708 as per Drg.Supply Basis |
| 12 | Conversion Basis |
| 13 | Machining Charge |
| 14 | Forge Steel Tail Bar For TAXMACO and KCP Mill Having Material C-40/8 As per DRG. MH- 6 & MH-56Supply Basis |
| 15 | Conversion Basis |
| 16 | Forge Steel Pinion For Transmission Gear OF TAXMACO Mill as per DRG. No. MH 39,Material EN-24,Tensile Strength70-80 Kg./sqcm, Hardness 200-220 BHN |
| 17 | C.S.Bearing Housing For TAXMACO Mill As per DEG No MH-17-C/04 Side Roller Housing Supply Basis |
| 18 | Conversion Basis |
| 19 | C.S.Bearing Housing For K.C.P.Mill As per DRG no MH-17-B Side Roller Housing Supply Basis |
| 20 | Conversion Basis |
| 21 | C.S.Bearing Housing ForK.C.P.Mill As per DRG no MH-17-B Top Roller HousingSupply Basis |
| 22 | Conversion Basis |
| 23 | C.S.Gear Coupling For C/F Machine As per DRG.No.BH-14 (Duly case Hardness) |
| 24 | C.S. Pinion For Cane Unloader As per DRG, CU- 16TEETH-17 |
| 25 | TEETH -18 |
| 26 | C.S.Sprocket 2\" Pitch (Both Pilot Bore)(i) No Of Teeth 18 , Boss DIA 3\" |
| 27 | (ii) No Of Teeth 36 , Boss DIA 6\" |
| 28 | C.S.Sprocket For Boiler rotary feederas per DRG.BLR-73/1 Pitch- 25.0 MM,No Of Teeth 21, OD -180MM. P.B -25MM |
| 29 | C.S.Sprocket For Bagasse elevator(Pilot Bore) as per DRG.MH-75 Pitch 50.8 MM,No Of Teeth 50, OD 842.70MM. PCD 808.7MM,Teeth Thickness 28mm , Boss- 270x130 mm |
| 30 | CS Sprocket (Pilot Bore ) as per DRG.BLR-62Pitch 50.8 mm, no.Of Teeth-14 PCD 226.49mm,OD 258.8mm |
| 31 | Static Coller OF 25 mm Thick Duly Hard Faced OF 5 mm Thick Layer . Total Thick 30 mm After Hard Facing For TAXMACo & KCP Mill As per Drawing No. MM 105(i) M.S. Material |
| 32 | (ii) C.S.Material |
| 33 | Sprocket Of Inter Carrier OD 280 MM,No.Of Teeth45.Pitch 19.5 MM |
| 34 | C.S. Sprocket (DUPLEX) For Enter Carrier Teeth 12, As per DRG. MH-72/Sample |
| 35 | S.S. Wear Plate IS 304 Quality (i) Length 435 MMx Width 370 MMx Thick 15 MM |
| 36 | (ii) Length 385 MM x Width 330 MM x Thick 15 MM |
| 37 | C.S.Tresh Beam Bracket As per Sample /DRG. |
| 38 | C.S.Eccentric Pin For TAXMACO As per Sample/ Drg. |
| 39 | C.S. Trash Beam Adjusting Connecting Rod For TAXMACO Mill, as per Drg. MH- 297 |
| 40 | C.S. Bridge Wheel For Cane Unloader As per Drg. CU25 (1), |
| 41 | Trolly Wheel For Cane Unloader As per Sample /DRG. |
| 42 | Pinion Gear Set For Cane Unloader As per Sample /DRG |
| 43 | C.S. Pinion (Gear) For RBC Cross Carrier Pitch 41MM. Teeth 25 , Type Of Teeth In Valute (Spur) Module 12.7 MM Width 125 MM .OD 343 MM, Bore 2\" DIA As per DRG. |
| 44 | Clutch Shaft For Mill. As per DRG. MH-76 , EN-8For TAXMACO Mill -Sl.No.2 |
| 45 | For KCP Mill - Sl.No.1 |
| 46 | CS Worm For Crystilizer Wheel OD 290 MM, Bore 81 MM.Pitch 80 MM Complete |
| 47 | Groving Of C.Strash Plate As Per DRG. |
| 48 | Idler wheel gear for cane unloader., No of Teeth 68, OD-420 mm, Module-6, Pitch- 18.84 mm, PCD-408 mm, as per drg. No. CU-25 (I) |
| 49 | Pinion for cane unloader No. Of teeth- 33, OD-212 mm, PCD-198 mm, pitch- 18.84 mm, module-6 as per drg. No. |
| 50 | Pinion for cane unloader No. Of teeth- 18, OD-200 mm, pitch- 35 mm, bore- 50 mm, width-115 mm, module-6, Teeth depth-25 mm as per drg. No. |
| 51 | Break stand complete for cane Unloader, Size-10\" |
| 52 | CS Sprocket of RBC, Nos of teeth 12, as per drg. BLR 32/93 |
| 53 | Chain Sprocket for inter carrier clucth shaft, OD 280, PCD 270, Bore 108, Root dia 260, Nos of teeth 45, Nos of hole 4, as per drg. 001 |
| 54 | CHIEF ENGINEER |
