|
| 1 | Excavation in post holes each not exceeding 0.5 Cu.m, getting out in hard / dense soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed. |
| 2 | Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.0 KMcomplete all as specified and as directed. |
| 3 | Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.00 KMcomplete all as specified and as directed. |
| 4 | Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.00 KM complete all as specified and as directed. |
| 5 | M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Bed blocks and Bed plates including weathering, slightly rounded or chamfered angles and throating, necessary form work etc complete all as specified and directed. |
| 6 | M & L for PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed. |
| 7 | M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed. |
| 8 | M & L for PCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings, Coping etc. complete all as specified and as directed. |
| 9 | M & L for PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in copingcomplete all as specified and as directed. |
| 10 | M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed. |
| 11 | M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed. |
| 12 | Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed. |
| 13 | M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc. complete all as specified. |
| 14 | Use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. |
| 15 | M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified. |
| 16 | Use and removal ofsteel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed. |
| 17 | Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.0 KM complete all as specified and as directed. |
| 18 | M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed. |
| 19 | M & L for Providing Precast Cement Concrete Solid Block Masonry of 1:3:6, Type C1 using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in cement mortar 1:6 complete all as specified and as directed. |
| 20 | Dismantling Fencing Wire Mesh of any type complete all as specified and as directed. |
| 21 | Dismantling fencing post (RCC) or steel of any section including taking out embedded portion and making good disturb ground complete all as specified and as directed. |
| 22 | S & F in repairs PVC Coated Chain Link MS Galvanised Fencing Mesh of size 50 mm X 50mm, 4mm dia wire with minimum 1 mm thick PVC Coating and of weight not less than 4.5 KG / Sq.m including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed. |
| 23 | S & F in repairs Galvanised, 2 Strand, Steel Barbed Wire 2.24mm dia, Barbed with 2mm dia bars at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.Note: Each line of wire will be measured for payment. |
| 24 | S & F in repairs Concertina Coil Fencing with Razor punched barb tape Concertina Coil made from High Tensile Spring Steel, High Carbon Wire conforming to IS – 4454 [Part – 1], of Grade –SM duly Hot Dipped Galvanised, 600mm dia, 10 Metre openable length, with Galvanised coating and Punched Tape material as per IS – 513, having 50 Nos Rounds per 6 Metre length [before stretching], having medium barbs [Barb length 24±1mm, Pitch between two barbs 35±1mm], Spring Core Wire [2.5 mm thick] of high tensile strength of 165 Kg / Sq.mm with tape [0.52mm thick] and weight 43.478 Grams / Metre and fixing to “Y” or Trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6/9 horizontal RBT [Reinforced Barbed Tape] Wire, Stud tied with GI Staples and GI Clips to retain horizontal, including necessary bolts and coating with Px Compound [Anti Rust] complete all as specified and as directed. Note: Horizontal barbed wire & angle iron supports shall be measured and paid separately under relevant items of Schedule \"A\". Measurement shall be made for stretched length. |
| 25 | S & F in repairs Concertina Coil Fencing with Razor punched barb tape Concertina Coil made from High Tensile Spring Steel, High Carbon Wire conforming to IS – 4454 [Part – 1], of Grade –SM duly Hot Dipped Galvanised, 1050mm dia, 10 Metre openable length, with Galvanised coating and Punched Tape material as per IS – 513, having 50 Nos Rounds per 6 Metre length [before stretching], having medium barbs [Barb length 24±1mm, Pitch between two barbs 35±1mm], Spring Core Wire [2.5 mm thick] of high tensile strength of 165 Kg / Sq.mm with tape [0.52mm thick] and weight 43.478 Grams / Metre and fixing to “Y” or Trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6/9 horizontal RBT [Reinforced Barbed Tape] Wire, Stud tied with GI Staples and GI Clips to retain horizontal, including necessary bolts and coating with Px Compound [Anti Rust] complete all as specified and as directed. Note: Horizontal barbed wire & angle iron supports shall be measured and paid separately under relevant items of Schedule \"A\". Measurement shall be made for stretched length. |
| 26 | S & FMild Steel work conforming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embedding in concrete and screwing etc., Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bendingto shape, notching for wire, drilling holes or as in flat iron fillets [forsecuring wire mesh and barbed wire etc.] including all necessary drilling, bolting or riveting, etc. and similar work complete all as specified and directed. |
| 27 | S & F MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 10 cm long and not exceeding 15 cm long, dia of neck exceeding 11 mm but not exceeding 15 mm complete all as specified and as directed. |
| 28 | S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. |
| 29 | S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. |
| 30 | Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed. |
| 31 | S & F Mild Steel work confirming to Fe - 290, Grade E-165, as in framed work such as Grills, Gratings, Ladders etc with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work complete all as specified and as directed. |
| 32 | S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed. |
| 33 | S & F in repairs Rolled Mild Steel work conforming to Fe 410-W, Grade-E- 250, Quality-A as in Roof Trusses [framed], trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing [Beam, tee, angle, channel or flat sections] including distance pieces, cleats etc complete all as specified and as directed. |
| 34 | S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed. |
| 35 | Dismantling of Plain or Corrugated Steel sheeting of any gauge, thickness of roof in roof coverings, complete all as specified and as directed. |
| 36 | S & F pre-painted Galvalume steel sheets of Trapezoidal profile having pitch 190mm, depth 29mm or Tiled Profile and thickness 0.50mm [Galvalume base-PPGL trapezoidal profile sheets], having tensile strength of 550 Mpa, fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size in roof covering complete all as specified and as directed. Note: Overlap shall be provided as specified by the manufacturer. |
| 37 | S & F 0.8mm thick Plain, Galvanised, Mild Steel sheeting, in ridges, hips, valley gutters, drip and straight flashings [length and girth as required at site in single piece] with grade of Zinc coating 275 GSM fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size complete all as specified and as directed. |
| 38 | S & F 1.0mm thick Plain, Galvanised, Mild Steel sheeting, in ridges, hips, valley gutters, drip and straight flashings [length and girth as required at site in single piece] with grade of Zinc coating 275 GSM fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size complete all as specified and as directed. |
| 39 | M & L for PCC 1:2:4, Type B-1 [using 20 mm graded granite stone aggregate] in surface channels and drains including forming fair finished drain or channel of 30 cm inner girth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed. |
| 40 | All as per Serial Item No. 39but Add or deduct for each 25 mm girth or part thereof over or under 30cm complete all as specified and as directed. |
| 41 | M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Floors/ Hard standing etc, surface finished even and smooth with out using extra cement and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green and providing 10mm thick joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed. |
| 42 | M & L for 75 mm thick PCC 1:3:6, Type C-2, using 40 mm graded stone aggregate as in Sub base for flooring complete all as specified and as directed. |
| 43 | M & L for Chequered Cement Concrete Tiles of size 250 X 250 mm / 300 X 300 mm, 22mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 of cement complete all as specified and as directed. |
| 44 | M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 45 | M & L for Inter Locking Paving Blocks of 60mm thick, made with M-35 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern conforming to IS - 15658 set in floors complete all as specified and as directed. |
| 46 | M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed andpointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabsincluding screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves. |
| 47 | Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces, ceiling surfacesetc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.0 KM complete all as specified and as directed. |
| 48 | M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 49 | M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer of same manufacturer as that of paint on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed.Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicatorsbefore commencement of the work to GE for approval. |
| 50 | M & L for One coat of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed.Notes:- (a) The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicatorsbefore commencement of the work to GE for approval. |
| 51 | M & L for preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed. |
| 52 | M & L for preparation of old decorated surfaces of walls, pillasters, etc. including brooming down or steel wire brushing and applying one coat of white wash on wall complete all as specified and as directed. |
| 53 | M & L for Two coats of synthetic enamel paint on old painted wooden surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed. |
| 54 | M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. |
| 55 | M & L for One coat of synthetic enamel paint on old painted steel surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed. |
| 56 | M & L for Two coats of Cement Based paint over a coat of Alkali Resistant Primer by using auto roller/ airless sprayer on newly plastered Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed.Note:- The contractor shall carryout Cement Babsed Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Cement Based Painting through their authorised applicatorsbefore commencement of the work to GE for approval. |
| 57 | M & L for One coat of Cement Based paintby using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed.Note:- The contractor shall carryout Cement Babsed Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Cement Based Painting through their authorised applicatorsbefore commencement of the work to GE for approval. |
| 58 | M & L for 600 mm dia RCC Pipes, Class NP3, laid and jointed with collars laid in trenches and jointedwith cement mortar including taking down old unserviceable pipe of any size and description complete all as specified and as directed. |
