|
| 1 | Excavation of foundation in hard soil within 50 m initial lead and 1.5 m initial lift including rough dressing and levelling as per the direction of engineer in charge |
| 2 | Filling foundation and plinth with sand well rammed including cost and conveyance of materials. |
| 3 | C.C.(1:4:8) with 4 c.m. size h.g. metal in F&P. |
| 4 | C.C.(1:2:4) with 12 mm. size h.g. chips in F&P. |
| 5 | Brick work with K.B.Brick having crushing strength not less than 75 Kg/cm2 with dimensional tolerance ± 8 percent in cement mortar (1:6) in(a) foundation and plinth |
| 6 | (b) superstructure in ground floor |
| 7 | (c) superstructure in first floor |
| 8 | Brick work with K.B.Brick having crushing strength not less than 75 Kg/cm2 with dimensional tolerance ± 8 percent in cement mortar (1:4) in septic tank.(a) foundation and plinth |
| 9 | R.C.C. workofM-20 grade with 20mmand down grade black hard granite (crusherbroken) stone chips including hoisting and laying in ground floor(a) Column base, frustum, plinth band |
| 10 | (b) Bed Block |
| 11 | (c) Lintel |
| 12 | (d) Column and beam |
| 13 | (e) Sun shade, loft and Chajja |
| 14 | (f) Roof Slab |
| 15 | (g) Stair |
| 16 | R.C.C. workofM-20 grade with 20mmand down grade black hard granite (crusherbroken) stone chips including hoisting and laying in first floor(a) Bed Block |
| 17 | (b) Lintel |
| 18 | (c) Column and beam |
| 19 | (d) Sun shade, loft and Chajja |
| 20 | (e) Roof slab |
| 21 | Supplying, fitting and placing uncoated HYSD bar reinforcement complete as per drawing and technical specification in(a) ground floor |
| 22 | (b) first floor |
| 23 | 2.5 cm thick grading concrete (1:2:2) on roof slab with 6 mm size hard granite chips on new work(a) ground floor |
| 24 | (b) first floor |
| 25 | 16 mm thick cement plaster in c.m(1:6) over brick masonry, outer walls in(a) ground floor |
| 26 | (b) first floor |
| 27 | 12 mm thick cement plaster in c.m(1:6) over brick masonry, inside walls in(a) ground floor |
| 28 | (b) first floor |
| 29 | 12 mm thick cement plaster in c.m(1:4) over RCC work and brick masonry in septic tank |
| 30 | 6mmthickcementplasterincm(1:4),finishedsmooth including closed deep chiping and slurry treatment (a) ground floor |
| 31 | (b) first floor |
| 32 | Finishing wall surface with Acrylic wall putty (Water based) of approved make and finished smooth and even in (a) ground floor |
| 33 | (b) first floor |
| 34 | Primimg one coat with any approved primer over wall surface including cost of primer in (a) ground floor |
| 35 | (b) first floor |
| 36 | Distempering two coats to walls with distemper of approved shade on new work to give an even shade including cost of distemper in (a) ground floor |
| 37 | (b) first floor |
| 38 | Finishing exterior walls with weather coat of approved shade two coats on new work to give an even shade including cost of paint (a) ground floor |
| 39 | (b) first floor |
| 40 | Fixing of Vitrified (60 cm x 60 cm plain /ivory) in floors, treads or steps and landing on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete including cost of tiles. (a) ground floor |
| 41 | (b) first floor |
| 42 | Fixing of ceramic glazed tiles 30cmx20cm/20cmx20cm special plain/printed series in floors, treads or steps and landing on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete including cost of tiles (a) ground floor |
| 43 | (b) first floor |
| 44 | Fixing of Vitrified tiles 60 cm x 60 cm (plain / ivory) series in dado, skirting and risers of steps on 12mm thick cement plaster in mortar (1:3) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete including cost of precast tiles per 1 sqm. (a) ground floor |
| 45 | (b) first floor |
| 46 | Fixing of ceramic tiles in dado, skirting and risers of steps on 12mm thick cement plaster in mortar (1:3) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete including cost of precast tiles per 1 sqm. (a) ground floor |
| 47 | (b) first floor |
| 48 | Supplying, fitting, fixing up window (sliding type) made up of Aluminium section 151-154, 151-155 as window frame section; No 151-155, 151-153, and 151-167 as shutter frame with 5 mm thick black glass as panel fitted with rubber bending including locking arrangement and all fittings including cost of all materials, taxes, labour, T&P complete |
| 49 | Providing, fitting and fixing of Al door with OEL anodized Al door section of 9202 as vertical member, 9201 as top member and 9200 as bottom and middle member and 12 mm prelaminated board fixed on door frame by means of tapered clip No 4660 and the frame to be completed by means of jointing angle No 1855 including all cost of labour, T&P, hire charges of drilling machine, labour charges etc complete. |
| 50 | Providing, fitting and fixing up partition walling (Fixed Glazed) with OEL Aluminium anodized section No, 9210 and 9207 as single groove and double groove respectively as horizontal and vertical member and OEL section 4660 as taperedclip for fixing up 6 mm thick glass and jointing angle no, 1855. |
| 51 | Supply, fitting and fixing of MS grill and ventilators including painting two coats over a coat of primer including cost of transportation. |
| 52 | Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm |
| 53 | 10 cm thick dry brick khoa backing in soakpit. |
| 54 | Filling F&P with excavated earth, ramming and shaping into proper shape |
| 55 | Recessed wiring to Light point / Exhaust fan point with switch (Module) Recessed wiring to light point/Fan point/ Exhaust fan point/Call bell point with 1.5sq.mmFR PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non- metallic PVC flexible conduit with 5A 25 on MS box having front bakelite cover of suitable size, MS box with 1.5sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accessories and connection (Make of wire-Finolex/L&T/Anchor/HavellsN-Guard/ Great White/HPL) with all cost of material and labour etc. Light Point / Exhaust Fan Point (Module)(Short) |
| 56 | Light Point / Exhaust Fan Point (Module)(Medium) |
| 57 | Light Point /Exhaust Fan Point (Module) (Long) |
| 58 | Supply & Fixing of 5 Amps. Wall socket on existing Board (Module) |
| 59 | Supply & Fixing of 5 Amps. Wall socket with witch on Separate Board(Module) |
| 60 | Supply & Fixing of 15 Amps. Switch & Socket (Module) |
| 61 | Recessed wiring to Sub-main along with the following size of PVC insulated single core multistrand copper conducter ISI marked in 20 mm dia non metalic heavy duty flexible conduct 1.6 mm in Recessed PVC conduct as required (Make -Finolex/L&T/Anchor/Havels/V-Guard) 2 x 2.5 sqmm + 1x1.5 sqmm run in 25 mm dia felxiable conduit |
| 62 | 2 x 4 sqmm + 1x 1.5 sqmm run in 25 mm dia felxiable conduit |
| 63 | 2 x 6 sqmm + 1 x 2.5 sqmm run in 25 mm dia felxiable conduit |
| 64 | Supply and fixing of 32 Amp FT / DP switch (Make-Cona/Anchor) |
| 65 | Supplying & Fixing of Angle Batten Holder / Batten Holder |
| 66 | Supplying fitting & fixing of 6 Way BDB with 6 MCB |
| 67 | 32 Amp. Double pole MCB |
| 68 | Supplying & fixing of Earth Bus Bar of 50 mm X 5 mm and 500 mm Long. |
| 69 | Supply and fixing of fan hook 16sq. mm Rodin R.C.C. roof with all accessories |
| 70 | Supply and fitting of 63A ICTPN main switch on MS frame |
| 71 | Supply and fixing of fan hook 16sq. mm Rodin R.C.C. roof with all accessories. |
| 72 | Supplying & Fixing of Ceiling Rose |
| 73 | A.C Ceiling fan 48/56\" |
| 74 | Exhaust Fan / Wall Fan (10\"/12\" size) |
| 75 | Electronics step type Regulator |
| 76 | S/F of 15W Circular LED surface fitting (Make - Havells / Phillips/Bajaj) |
| 77 | S/F og 60W LED street light fittings (Make - Havells / Phillips/Bajaj) |
| 78 | S/F of 15W LED light fitting (Make - Havells / Phillips/Bajaj) |
| 79 | Supply and fixing of standard earthing with 40mm diameter G.I. Pipe 3 meter long. 12mm diameter 15cm. holes 40mm diameter flange at top with R.C.C. earth pit chamber, masonary wall work, Alternate layer of charcoal and salt, complete with all accessories. (Earthing) |
| 80 | Supply and fitting of 6mm 2 PVC twin core Aluminium wire with G.I wire for service connection. |
| 81 | Supplaying all materals,labours, taxes and tools and plants for fittings and fixing of PVCpipes,class- confirming to ASTM-D-1785/89(Sch-80) and pipe fittings of the following nominal bore with clamps fittings including making good the wall,ceilling and floor,testing all complite as per specification and direction of the Engineer -in-charge. 25 mm dia PVC Pipe |
| 82 | 50 mm dia PVC pipe |
| 83 | Supplaying all materals,labours, taxes and tools and plants for fittings and fixing of CPVCpipes, confirming to IS:15778 having thermal stability for hot &cold water supplay,including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m specing, with jointing the pipes with CPVC solvent cement and testing the joints completeas per specification and direction of the Engineer -in-charge. 20 mm dia CPVC Pipe |
| 84 | 25 mm dia CPVC Pipe |
| 85 | Supplying, fitting, fixing of50 mm dia. G I bendetc. complete |
| 86 | Supplying, fitting, fixing of50 mm dia. G I Tee etc. complete |
| 87 | Cutting grooves in pucca floors and walls for taking CPVC pipe s and making good the damages as per specification and direction of the Engineer -in-charge. |
| 88 | Cutting holes through existing brick work for taking CPVC pipe s and making good the damageswith cement morter (1:6) as per specification and direction of the Engineer -in-charge. |
| 89 | Cutting holes through existing in R.C.C. Floors and roofs upto 19 cm.for taking CPVC pipe s and making good the damageswith cement voncrete(1:2:4) as per specification and direction of the Engineer -in-charge. |
| 90 | 15 mm dia CP Brass Short Body Bib cock . |
| 91 | 15 mm dia CP Brass long body Bib cock . |
| 92 | 15 mm dia CP flanges |
| 93 | Supplying all materals,labours, taxes and tools and plants for fittings and fixing of brass screw-down Stop cock / CPittings of the following IS:781-1995 approved make including supplay all nessary jointining material compliteas per specification and direction of the Engineer -in-charge. 15 mm dia CP Brass Stop Cock |
| 94 | 15 mm dia CP Pillar Cock |
| 95 | Supplying, fitting, fixing of 15 mm dia CP concealed stopcocketc. Complete. |
| 96 | Supplying all materils,labour,T&P and fixing Rotational moulded polithylene cylindrical vertical water storage tanks(SYNTEX)conforming to IS 12701-1996 Including cutting holes through the tank and fixing mild steel tubes and fittings and providinng extra socket and jam nuts,fixing ball valave etc,including hoisting up to a heightofextra 5 Meters above ground level and placing the tank to the required positionetc, all as per speci fication and directionof the Engineer incharge. 1000 liter capacity Syntex/FC Tank |
| 97 | Supplying, fitting, fixing of 15mmdia. PVC connection pipe for pillarcock, supply mains for wash basin etc. Complete. Supplying, fitting, fixing of 15mmdia. PVC connection pipe for pillarcock, supply mains for wash basin etc. Complete. |
| 98 | Supplying all materials,labour,T&P and fitting, fixining following PVC itemsand filling of the following outside diameter conformoring to IS 13592 Type A, to walls with seal ring conforming to IS:5382,leaving 10 mm gap for 10mm thermal expansion,(1) single socket pipes as per manufactures specification testing, all complite as per specificationand directionof the Engineer incharge. 75 mm dia U-PVC Soil, Waste, Rainwater pipes |
| 99 | 50 mm dia PVC plain bend |
| 100 | 50 mm dia UPVC pipe (4 kgf/cm 2 ) |
| 101 | 50 mm dia UPVCdoor bend |
| 102 | 50 mm dia UPVCplain bend |
| 103 | 75 mm x 50 mm dia UPVCR/Socket |
| 104 | 100 mm x 50 mm dia UPVCR/Socket |
| 105 | 110 mm dia UPVC pipe (4 kgf/cm 2 ) |
| 106 | 110 mm dia UPVCdoor Tee |
| 107 | 110 mm dia UPVCdoor bend |
| 108 | 110 mm dia UPVCplain Tee |
| 109 | 110 mm dia UPVCplain bend |
| 110 | 110 mm dia UPVCCowl |
| 111 | Supplying all materials,labour,T&P and fitting, fixining ,laying in trenches High Density Polythinepipes conforming to IS-4984-1995 and specials of the following outside diameter conformoring to Class 1 to Class 3 and jointing by fusion welding method including testingas per manufactures specification testing, all complite as per specificationand directionof the Engineer incharge (Earth work in trenches measured separetly).110 mm dia H.D.Pvc Pipe |
| 112 | Supplying all materials,labour,T&P and fitting, fixining of Wash down water Closest (Europian type W.C pan) with Integral\"S\" or \"P\" trap conforming to IS 2556:Part 8-2004, to the floor with Wooden Plug And Chromium plated screws including jointingthe trap with soil pipe in cement mortar (1:1) etc,,all complite as per specification and direction of the Engineer inchargr.(Without Seat &Cover) White Vitreous China EWC Pattern with \"P\" Trap |
| 113 | Supplying all materials,labour T &P Fitting of 10 liters capacity PVC L L flushing Cistern with manually controlled device(handle lever) conforming to IS :7231,etc all complite as per specification and direction of the Engineer incharge. . 10 Liters P.V.C.low level Flushing Cystern |
| 114 | Supplying all materials,labour T &P Fitting of Plastic Seatand cover for wash down water closet with cromium plated brass hinges and rubber buffer etc all complite as per specification and direction of the Engineer incharge. . White Plastic Seat &cover with CP Brass Hinges |
| 115 | Supplying all materils,labour, T&P fitting,fixing of Long Bowl Pattern Urinal conforming to IS 2556: Part 6-1996 includingconnectiont the Urinalof Angle back 450x375x350 mm sizes respectvely with waste pipe by means of white cement(lead) mixed with chopped hemp etc ,as per specification and direction of the Engineer -in-charge Virtious China -Angle Back Urinal of 450mm x 375 mmx 350 (Parryware/Hindustan) |
| 116 | Supplying all materils,labour, T&P fitting,fixing of glazed earthenware Ladies urinal (squating plate) of size 600 mm x 350 mm conforming to IS:2556-Part-6-1995 with integral longitudinal flushing pipe including embedding the plate 25mm cement morter (1:8) laid over 150mm cement concrete (1:4:8) using 40mm hard granite metal etc ,as per specification and direction of the Engineer -in-charge Ladies urinal (Virtious china sqatting plate urinal) size 600mmx350 mm |
| 117 | Supplying all materils,labour, T&P fitting,fixing of Stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1:8 cm thick, fixed in urinal partitions by cutting a chase of appropiate width with chase cutter and embedding the stone in the chase with epoxygrout or with concrete 1:2:4 etc ,as per specification and direction of the Engineer -in-charge. Grinite stone Partition Wall (75 cm. x50 cm.) |
| 118 | Supplying all materils,labour, T&P fitting,fixing ofVirtious China flat Wash basin over sizes 550 mm x 400 mm with hole for pillar taps conformoing to IS 2556 : Part 4-2004 with cast iron or M.S Brackets painted white cement including cutting holes in walls and making good the damages etc. All complite as per specificationand direction of the Engineer-in-charge.Virtious China flat wash basin of 550mm x400 mm(Parryware/Hindustan) |
| 119 | Supplying all materils,labour, T&P fitting,fixing ofFire clay Kitchen Sinkover sizes 600 mm x 450 mm X 250 mm with hole for pillar taps conformoing to IS 2556 : Part 5-1994 with cast iron or M.S Brackets painted white cement including cutting holes in walls and making good the damages etc. All complite as per specificationand direction of the Engineer-in-charge.Kitchen Sink over Sizes 600 mm X 450mm X250mm |
| 120 | Supplying all materils,labour, T & P fitting,fixing ofPVC waste pipe for wash basin or sink i.e Flexiable (Coil shaped) PVC Waste pipe 40mm dia with length not less than 700 mm with PVC waste fittings etc. All complite as per specificationand direction of the Engineer-in-charge.Flexible (coil shaped) PVC waste pipefor sink & wash basin 32 mm dia with 900 mm long waste fittings |
| 121 | Supplying all materils,labour, T&P fitting,fixing ofCP brass towel rail wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge.25 mm dia x 600 mm long. |
| 122 | Supplying all materils,labour, T&P fitting,fixing of plate glass shelf with CP brass brackets wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge.120 mm x600 mm |
| 123 | Supplying all materils,labour, T&P fitting,fixing of bevelled type plate glass mirroor with wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge.600 mm x 450mm |
| 124 | Supplying all materils,labour, T&P fitting,fixing of Cp soap Holder standard sizewith wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge. |
| 125 | Supplying all materils,labour, T&P fitting,fixing ofCP brass towel ring wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge.CP Brass Towel Ring |
| 126 | Supplying, fitting, fixing of2’ – 0” long CP towel rail etc. Complete. |
| 127 | Supplying all materils,labour, T&P fitting,fixing ofLiquid Soap Container with wooden plugs CP srew and cement etc. All complite as per specificationand direction of the Engineer-in-charge. |
| 128 | Supplaying all materals,labours, taxes and tools and plants for fittings and fixing of CP Brass Shower rose with CP revolving Shower with 15 to 20 mm inlet & 150 mm dia etc compliteas per specification and direction of the Engineer -in-charge. |
| 129 | Supplying all materials,labour and fixing of Piller taps capstan head screw down high pressure lettered \"Hot\" and \"Cold\" with long screws,shanks and back nutsof 15mm dia CP Wall mixerincluding all taxes etc complite as per direction by Engineer in charge. |
| 130 | Supplying all materials,labour and fixing of Brass Full Way Valve conforming to IS: 781-1995 of the 32 mm Full way Valves including all taxes etc complite as per direction by Engineer in charge. |
| 131 | Supplying all materials,labour and fixing of Brass Full Way Valve conforming to IS: 781-1995 of the 25 mm dia brass ball Valve including all taxes etc complite as per direction by Engineer in charge. |
