Tender For Comprehensive Maint To Tech Area ( Northern Side ) At Af Stn Sirsa. 1 Demolition Cement Concrete ( Un-Reinforced ) Of Any Description In Ground Floors, Pavings, Etc. Not Exc. 150Mm Thickness ( Above Or Below Ground Level ) And Removing Debris, Etc. To Outside Md / Af Land, Complete All As Specified And As Directed. 2 M&L For Cement Concrete 1:4:8 Type D2 ( 40Mm Graded Stone Aggregate ) 100Mm Thick In Sub-Bases, Complete All As Specified And As Directed. 3 M&L For Cement Concrete 1:2:4 Tybe B1 ( 20Mm Graded Stone Aggregate ) 100Mm Thick As In Flooring Complete All As Specified And As Directed. 4 M&L For Cementconcrete Type B-1, 1:2:4 ( 20Mm Graded Stone Aggregate ) 40Mm Thick As In Paths / Hardstanding Finishing Cement Concrete Surfaces Even And Smooth Without Using Extra Cement, Complete All As Specified And As Directed. 5 M&L For Cement Concrete 1:3:6 Type C2 ( 40Mm Graded Stone Aggregate ) , 75Mm Thick In Plinth Protectionfinishing Cement Concrete Surfaces Even And Smooth Without Using Extra Cement, Complete All As Specified And As Directed. 6 M&L For Machine Pressed Precast Conctete Interlocking Paver Block Any Shape And Size Confirming To Is 15658-2006 Of 60 Mm Thickness, M-35 Grade, With Grey Cement & No Pigment, Incl Taking Out Existing Old Paver Blocks And Removingfrom Sitecomplete All As Specified And Directed. 7 M&L For Sand Filling Under Floors Or In Foundation Incl Watering And Consolidation Complete All As Specified And Directed. 8 Taking Down Cement Plaster Including Raking Out Joints, Hacking For Key, Scrubbing Down With Water And Removing Debris, Etc. To Outside Md / Af Land, Complete All As Specified And As Directed. 9 M&L For 15 Mm Thick Plastering In Two Layers, 10 Mm + 5 Mm In Cement Mortar 1:4, Top Layer Of 5 Mm Thickness Mixed With With Water Proofing Compound ( As Per ManufacturerS Instructions ) Onbrick / Stone Walls Or Concrete Surfaces Finished Even And Fair ( Upto Any Height ) For External Surfacescomplete All As Specified And Directed.Note : Water Proofing Compound Shall Be Measured And Paid Seperately As Supply Only. 10 Supply Only Liquid Water Proofing Compound, Conforming To Is And / Or As Approved, Complete All As Specified. 11 M&L For Rough Cast Plaster On Brick Walls Consisting Under Coat Of Cement And Sand Mortar 1:3 Not Less Than 10Mm Thick And While It Is Still In Plastic State The Rough Cast Mixture Consisting Of Crushed Stone Or Fine Gravel Mixed With Coarse Sand And Cement In The Ratio 1:1:1 Shall Be Applied And Finish Even, Complete All As Specified And As Directed. 12 M&L For Preparing New Plastered Surfaces Of Walls And Applying Two Coats Of Weatherproof Exterior Emulsion Paint ( In Camouflage Pattern ) Over And Including Priming Coat With Suitable Exterior Primer, Applied As Per ManufacturerS Recommendations Complete All As Specified And As Directed. 13 M&L For Preparing New Rough Cast Plastered Surfaces Of Walls And Applying Two Coats Of Weatherproof Exterior Emulsion Paint ( In Camouflage Pattern ) Over And Including Priming Coat With Suitable Exterior Primer, Applied As Per ManufacturerS Recommendations Complete All As Specified And As Directed. 14 Demolition Of Brick Work Built In Cement Mortar And In Any Position Including All Quoins, Arches And Pillars, Etc. Incl Removal Of Debsris From Site Complete All As Specified And As Directed. 15 M&L For Brick Work With Fly-Ashbricks ( Old Size Bricks ) , Straight Or Curved On Plan Exc. 6.0 Metre Mean Radius, Built In Cement Mortar 1:6, Complete All As Specified And As Directed. 16 M&L Brick Work Using Serviceable Bricks Obtained From Item No. 16 Here-In-Before Including Removing Old Mortar, Straight Or Curved On Plan Exc. 6.0 Metre Mean Radius, Built In Cement Mortar 1:6, Complete All As Specified And As Directed. 17 Dismantling Of Asbestos Cement ( Corrugated, Semicorrugated, Plain, Etc. ) Sheets In Roof / Wall Coverings And Removal From Sitecomplete All As Specified And As Directed. 18 Dismantling Of Fibreglass / Polycarbonate Roofing Sheet ( Corrugated, Semicorrugated, Plain, Etc. ) Sheets In Roof / Wall Coverings And Removal From Sitecomplete All As Specified And As Directed. 19 S&F 0.50 Mm Thick Tct ( Total Coated Thickness ) Pre-Coloured Galvalume Sheets With Minimum Base Metal Thickness Of 0.45 Mm, Single Skin High Rib / Multi Rib Profile Galvalume Sheetinghaving 1000-1020 Mm Width And 28-30 Mm High Crest @ Maximum 250-255 Mm Pitch ( Centre ) With Sheets Manufactured Out Of 0.50 Mm This Tct ( Total Coated Thickness ) High Tensile Galvalume Sheets Having Tensile Strength 550 Mpa With 18-20 Micron Top Coat Over 5 Micron Primer And 8-10 Micron Alkyld Backer Zinc Aluminium Alloy Az-150, Sheets Having A Dip Metallic Zinc ( 43.5%0 Aluminium ( 55% ) & Silicon ( 1.5% ) With Total Mass Coating Of 150 Gms / Sqm On Both Sides, Having Wide Pans With Minimum 3 Smallstiffening Ribs For Effective Water Shedding And Special Male / Female Ends With Full Return Legs On Laps For Purlin Support And Fixed As Per Existing Profile Of Roof Completeall As Specified And Directed. 20 S&F Pre-Painted, Galvalume Aluminium Zinc Coating Gi Based Plain Steel Sheet, 0.50 Mm Thick Of Any Colour, Having Tensile Strength Of 550 Mpa, As In Roof Covering / Cladding To Wall, Fixed With Self Tapping Screws, Complete All As Specified And Directed. 21 Dismantling Structural Steel Work Of Any Description In Rafters, Purlins And Wind Ties Wtc And Removal From Site Complete All As Specified And Directed. 22 M&L For Steel Work In Tubular Trusses Including Special Shaped Washer Etc Complete Using Erw Or Induction Butt Welded Tubes Conforming To Is 1161-1979 Grade St-240 Complete All As Specified And Directed. ( Note: Quoted Rates Shall Be Deemed To Include For Cutting To Dead Length Where Required, Notching, Drilling, Fitting, Riveting And / Or Welding Or Connecting With Bolts And Nuts ( Including Rivets Or Bolts And Nuts ) , Providing And Fitting Angle Cleats, Fish Plates, Gusset Plates Etc., Also For Wedging, Plumbing, Truing Up And Fixing Complete ) 23 M&L For Preparing New Or Previously Untreated Steel And Iron Surfaces Of Any Description, Over 10 Cm Width Or Girth And Applying Two Coats Of Synthetic Enamel Paint ( First Quality ) Over A Red Oxide Zinc Chrome Primer, Complete All As Specified And As Directed. 24 Dismantling Wrought Iron Or Mild Steel Work Of Any Description In Rafters, Purlins And Wind Ties Wtc And Removal From Site Complete All As Specified And Directed. 25 M&L For Mild Steel Framed Work Such As Grills, Gratings, Etc.. With Ends Of Bars Shouldered And / Or Riveted, Or Forged Into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework Of Water Tanks And Similar Work Conforming To Fe.290.Gde-E-165 Complete All As Specified And Directed. 26 Dismantling Ofwallandceilingboards ( Fibre, Pulp, Insulation, Etc. ) Or Insulationboards / Slabs / Blankets, Any Thickness, Including Cover Fillets Incl Removal From Site Complete All As Specified And As As Directed. 27 S&F 6Mm Thick Hpsc Cement Fibre Plain Building Boards, Fixed To Wall, Including Finishing With 2 Mm Thick Wall Puttycomplete All As Specified And As Directed. 28 S&F False Ceiling With Powder Coated Exposed G.I. Grid Suspension System Consisting Of Main Runner 3600 Mm Long, Cross Tee 1200Mm / 600Mm Long And Wall Angle, Wall Angle Fixed On Pvc Dash Fasteners On The Perimeter Of The Wall By Steel Screws With Distance 300 Mm C / C, Main Runners Placed @ 1200Mm, Cross Tee 1200Mm Inserted In The Pre-Cut Slots Of Main Runner At A Regular Interval Of 600 Mm To Form A Modular Grid Of 1200Mm X 600Mm And Additional Cross Tees Of 600 Mm Placed Perpendicular To The Cross Tee 1200 Mm Long To Finally Form A Grid Of 600Mm X 600Mm, Grid Of Module Size 600Mm X 600Mm Shall Be Supported By 6 Mm Dia G.I. Wire From Purlins / Soffit Complete All As Specified And Directed. Note: Ceiling Board Will Measured And Paid Seperately Under Appropriate Item. 29 S&F 12Mm Thick Mineral Fibre Core Ceiling Board / Tiles For Insula-Tion And Accoustic Purposes, 60X60 Cm In Size, Fixed On Gi Snap Grid Frame Work With Steel Screws, Complete All As Specified And As Directed. 30 M&L For Solid Pvc Wall Lining Consisting Of 5Mm Thick Plain Colour Pvc Sheet Inclusive Of Solvent Cement And Fixing At Site On Pvc Frame, Including Various Pvc Angle / Section All As Per Manufacture Instruction And Specificationas Including Taking Down Carefully The Existing Electric Point Wiring And Making It Concealed By Cutting Grooves On Brick Walls As Required At Site For Wall Panelling Complete All As Specified And As Directed. 31 M&L For 5Mm Thick Pvc Sheet Fillet Of Width 35Mm For Wall Paneling Inclusive Of Fixing On To Wall To Make Pvc Frame As Per Specification And Drawing. 32 Dismantling Floor, Paver Tiles, Hearth Or Wall Tiling, Etc. Including Cement Mortar Bedding ( But Not Backing ) And Removing Debris, Etc. To Outside Md / Af Land, Complete All As Specified And As Directed. 33 M&L For Non-Skid Glazed Ceramic Coloured / Printed Floor Tiles 400X400x6.0 To 7.0Mm Thick In Flooring, Set And Jointed In Neat Cement Slurry And Pointed In White / Coloured Cement, Laid Over And Including 15Mm Thick Screed Or Screed Bed In Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Included In The Quoted Unit Rate. 34 M&L For Coloured Glazed Ceramic Tiles In Vertical Surface 450X 350X 7Mm Thick Set And Jointed In Neat Cement Slurry And Pointed In White Or Colour Cement To Match The Tiles, Laid Over And Including 10Mm Thick Rendering As Screed Or Backing Coat Of Wall Tilein Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Included In The Quoted Unit Rate. 35 M&L Coloured Glazed Ceramic Tiles 300X200x6.0 To 7.0Mm Thick In Vertical Surface I.E. Dado, Skirting, Etc., Set And Jointed In Neat Cement Slurry And Pointed In White Or Colour Cement To Match The Tiles, Laid Over And Including 10Mm Thick Screed Or Screed Bed In Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Included In The Quoted Unit Rate. 36 M&L For Vitirified Coloured Tiles 9 To 10Mm Thick ( Square / Rectangular ) , Double Charged, Light Shade, Polished, Area Of Each Tile Not Exc. 0.36 Square Metre In Floors, Etc. Set And Jointed In Neat Cement Slurry And Pointed In White Or Coloured Cement To Match The Tiles, Laid Over And Including 15Mm Thick Screed Or Screed Bed In Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Include In The Quoted Unit Rate. 37 M&L For Vtirified Coloured Tiles 9 To 10Mm Thick ( Square / Rectangular ) Double Charged, Light Shade, Polished, Area Of Each Tile Not Exc. 0.36 Square Metre In Vertical Surface I.E. Dado, Skirting, Etc., Set And Jointed In Neat Cement Slurry And Pointed In White Or Colour Cement To Match The Tiles, Laid Over And Including 10Mm Thick Screed Or Screed Bed In Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Include In The Quoted Unit Rate. 38 M&L Dismantling Stone Slabs And / Or Tiles Of Any Description Or Thickness In Floors, Aprons, Etc. Laid, Bedded And Pointed In Cement Mortar, Removal Of Debris Outside Af Land, Cleaning Of Area To Remove Dust, Loose Particles, Washing With Water And Providingmachine Cut Kota Stone Slab 20-25Mm Thick In Flooring, Laid Over 20Mm Thick Screed Base In Cement Mortar 1:4 Laid And Joined With Grey Cement Slurry Mixed With Pigment To Match The Shade Of The Slab Including Rubbing And Polishing, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Include In The Quoted Unit Rate. 39 M&L Dismantling Stone Slabs And / Or Tiles Of Any Description Or Thickness In Floors, Aprons, Etc. Laid, Bedded And Pointed In Cement Mortar, Removal Of Debris Outside Af Land, Cleaning Of Area To Remove Dust, Loose Particles, Washing With Water And Providinggranite ( Of Any Type ) Tiles, 18-20Mm Thick, Machine Cut, Bedded And Jointed With Grey Cement Slurry And Pointed With White Cement And Admixture Of Pigment To Match The Shade Of Granite Stone Including Grinding And Polishing, Laid Over And Including 20Mm Thick Screed Or Screed Bed In Cement Mortar 1:4, Complete All As Specified And As Directed.Note : Cost Of Cement Screed Bed Shall Deem To Be Included In The Quoted Unit Rate. 40 M&L For Rcc 1:2:4 ( Type B1 ) Using 20Mm Graded Aggregate As Counter / Platform Supported On Walls, Beams And Columns In Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs And In Shelves And The Like Complete All As Specified And As Directed. 41 M&L For Mild Steel Bars 10Mm Dia And Over, Cut To Length, Bent To Shape Required, Including Cranking, Bending Spirally For Hooping For Columns, Hooking Ends And Binding With And Including Mild Steel Wire ( Annealed ) Not Less Than 0.9Mm Dia Complete All As Specified And Directed. 42 S&F In Repair Rotational Moulded Polyethene Water Storage Tank, 500 Litre Capacity, Cylindrical, Vertical With Closed Top, 3 Layered, Conforming To Is, Hoisted And Fixed In Position Complete All As Specified And As Directed. 43 S&F In Repair Rotational Moulded Polyethene Water Storage Tank, 1000 Litre Capacity, Cylindrical, Vertical With Closed Top, 3 Layered, Conforming To Is, Hoisted And Fixed In Position Complete All As Specified And As Directed. 44 S&F In Repairball Brass Valves, High Pressure, With Polythene Float And Flynut Complete For 20Mm Dia Bore Pipe , Screwed For Iron Pipe Or Brass Ferrule And Fixed Complete All As Specified And As Dieceted. 45 S&F In Repair Looking Mirror 5.0Mm Thick Of Size 600X600mm, Fixed With Chromium Plated Brass Spacers 25Mm To 30Mm In Size ( One Each Corner ) Including Rounding The Edges Of The Mirror And Fixed-In-Repairs, Complete All As Specified And As Directed. 46 S&F In Repair Brass Chromium Plated Tubular Towel Rail 20Mm Dia, 60 Cm Long With Brackets Complete All As Specified And As Directed. 47 S&F In Repair Stainless Steel Grating Round 100Mm Dia With Waste Hole Jointing With Solvent Cement Complete All As Specified And As Directed. 48 S&F In Repair Chromium Plated Health Faucet With 1Mtr Stainless Steel Tube Indcluding Necessary Fitting And Fixtures Complete All As Specified And As Directed By Engr-In-Charge. 49 S&F In Repair Vitreous China, White, Half Stall Urinal Flat Back With Grating And Union For Discharge Pipe ( Excl Flush Pipe And Flushing Cistern And Waste Pipe ) Complete Including Providing And Fixing Plugs, Bedding Urinal Against Wall In Cement Mortar 1:2, Securing Urinal To Plugs With And Including 60Mm Long Brass Screws, Pointing Around Urinal Back In Cement; Fixing Flush Pipe, Grating And Union For Discharge Pipe Complete All As Specified And Directed. 50 S&F Brass Chromium Plated Urinal Spreader For Fixing With 15 Mm Dia Pipe Complete All As Specified And As Directed. 51 S&F In Repair 75Mm Bore Pvc ( Swr ) Pipes Single Socketed, In Any Length With Rubber Ring Joints, Laid In Trenches Or In Floors Complete All As Specified And As Directed. 52 S&F In Repair 110Mm Bore Pvc ( Swr ) Pipes Single Socketed, In Any Length With Rubber Ring Joints, Laid In Trenches Or In Floors Complete All As Specified And As Directed. 53 S&F In Repair Pvc ( Swr ) Bends Any 75Mm Bore Complete All As Specified And As Directed 54 S&F In Repair Pvc ( Swr ) Bends Any 110Mm Bore Complete All As Specified And As Directed 55 S&F In Repair 75Mm Bore Pvc ( Swr ) Floor Trap, Plain With Grating Including Jointing With Solvent Cement 56 Taking Up Or Down Steel Tubing 15Mm Bore ( Dia ) And Connections, Segregating The Serviceable Pipes And Connections, Stacking Properly At Site ( S ) And Keep In Safe Custody For Re-Use, Complete All As Specified And As Directed. 57 Taking Up Or Down Steel Tubing 20Mm Bore ( Dia ) And Connections, Segregating The Serviceable Pipes And Connections, Stacking Properly At Site ( S ) And Keep In Safe Custody For Re-Use, Complete All As Specified And As Directed. 58 Supply & Laying Steel Water Tubing 15Mm Bore ( Dia ) , Galvanised, ‘Medium Grade’ With All Fittings, Fixed On Walls, Ceiling Or Laid In Floors Or Any Other Situation, Complete As All Specified And As Directed. 59 Refixing Old Steel Tubing 15Mm Bore ( Dia ) And Connections ( Serviceable Pipes And Connections Obtained From Item Here-In-Before ) In New Or Old Position ( Walls, Ceiling, Floors, Etc. ) Including Cleaning Both Inner And Outer Surfaces Of Pipes By Using Wire Brush Including Provision Of New Gi Connections ( As Required Ordered At Sites ) , Complete All As Specified And As Directed. 60 Supply & Laying Steel Water Tubing 20Mm Bore ( Dia ) , Galvanised, ‘Medium Grade’ With All Fittings, Fixed On Walls, Ceiling Or Laid In Floors Or Any Other Situation, Complete As All Specified And As Directed. 61 Refixing Old Steel Tubing 20Mm Bore ( Dia ) And Connections ( Serviceable Pipes And Connections Obtained From Item No. 15 Here-In-Before ) In New Or Old Position ( Walls, Ceiling, Floors, Etc. ) Including Cleaning Both Inner And Outer Surfaces Of Pipes By Using Wire Brush Including Provision Of New Gi Connections ( As Required Ordered At Sites ) , Complete All As Specified And As Directed. 62 S&F Vitreous China White Squatting Pan Of Size 580X440mm, Orissa Pattern With Integral Foot Rests, ‘P’ Or ‘S’ Trap, Providing Joints Between Flush Pipe And Socket Of Wc Pan, Cones, India Rubber ( Nozzles Of Wc Pan ) Incluiding Provision Of Lime Concrete Bedding And Making Good To Floor / Distrubed Surfaces And Fixed-In-Repairs, Complete All As Specified And As Directed. 63 S&F In Repair Pvc Flushing Cistern 10 Litre Capacity White, Low Level, Valve Less, Syphonic Action Type With Inlet, Ball Valve, Float And Handle, Pvc Waste Pipe 32Mm Bore ( Dia ) Of Suitable Length, A Pair Of Cast Iron Bracket / Erecting Stand Duly Painted Including Cutting And Pinning In Ends, Making Good Disturbed Surfaces In Cement Mortar 1:3 And Fixed-In-Repairs, Complete All As Specified And As Directed. 64 S&F In Repair Vitreous China Wash Basin, White, Flat Back, Size 550X400mmexcluding Taps, Waste, Chain And Plug And Porcelain Stopper Butincluding Brackets Cutting For And Pinning In Ends Of Brackets Or Erecting Stand But Exclusive Of Fixing Of Supply And Waste Pipe 65 S&F In Repair Bib Tap 15Mm Bore ( Dia ) , Cast Copper Alloy, Chromium Plated, Fancy Type, Longbody With Capstan Head, Screwed Down, Screwed For Iron Pipe Or For Brass Ferrule, Complete All As Specified And As Directed. 66 S&F In Repair Pillar Taps, Cast Copper Alloy, With Capstan Heads, Chromium Plated, Facny Type Screwed Down High Pressure, With Or Without Lettered Hot Or Cold With Long Screwed Shanks And Fly-Nuts, Screwed For Iron Pipe And Fixed 67 S&F In Repair Stop Cock 15Mm Bore ( Dia ) , Cast Copper Alloy, Chromium Plated, Fancy Type With Long Shank And Cup ( Concealed Type ) , Screwed Down, High Pressure, With Crutch Or Butter-Fly Handle, Screwed Both Ends For Iron Pipe Or For Unions And Fixed-In-Repairs, Complete All As Specified And As Directed. 68 S&F In Repair Angle Valve 15Mm Bore ( Dia ) , Cast Copper Alloy, Chromium Plated, Fancy Type, Screwed Down, High Pressure, Screwed Both Ends For Iron Pipe And Fixed-In-Repairs, Complete All As Specified And As Directed. 69 S&F In Repair Pvc Waste Pipe 32Mm Dia ( Bore ) Having 600Mm Long And Fixed Complete To Walls, Ceilings Or In Floors, Etc.And Fixed-In-Repairs, Complete All As Specified And As Directed. 70 S&F In Repair Pvc Connection Pipe 15Mm Size And 60 Cm In Length With Adopter Nuts Of Pvc And Fixed-In-Repairs, Complete All As Specified And As Directed. 71 Taking Down Wooden Chowkat Or Frame With Shutter ( Without Taking Off Shutter From The Frame ) , Exc. 1.5 Square Metre But Not Exc. 4.0 Square Metre Each, Complete All As Specified And As Directed. 72 Taking Down And Refixing Of Shutters Of Any Descriptionin Same Opening N Exc 1Sq. M Each Complete All As Specified And As Directed. 73 Taking Down Shutters Of Any Descriptionn Exc 1 Sqm Each Complete All As Specified And As Directed. 74 Supply And Fixed Steel Windows With Side Hung Shutters Including Projecting Type Hinges With Steel Handle, And Steel Peg Stay, Complete With Glazing Bars, Dovetailed Or Welded For Fixing Wire Mesh Including One Shop Coat Of Priming, Complete All As Specified And Directed. ( Note : Sheet Glass For Glazing Shall Be Measured And Paid Seperately ) 75 Taking Down Chowkat Or Frame ( Any Type ) With Shutter ( Without Taking Off Shutter From The Frame ) , N.Exc. 1.5 Square Metre Each, Complete All As Specified And As Directed. 76 S&F Steel Rolling Shutters Thickness Of Lath 1Mm, Gear Operated Type With Bevel Gear Box And Crank Handlewith Out Ball Bearing, As Specified Including Top Cover, Anchoring Rod, Hasp And Staple And One Shop Coat Of Primer; Erected In Position As Indicated, Complete All As Specifeid And As Directed. 77 M&L For Mild Steel Framed Work As In Doors Or Gates Of Angle Or Other Section With Gusset Plates, Rails, Braces, Etc., Complete, Drilled For Fixing Of Steel Sheeting Or Other Covering. Doors, Etc. To Be Prepared For Hanging Or Sliding With And Including Either Hooks And Hinges Or Steel Hanging Door Fittings ( Exclusive Of Steel Sheeting Or Other Covering, Running Rails And Guides ) And Hanging; Also Fastening And Fixing Complete Fe-290, ( Gde E- 165 ) Complete All As Specified And Directed. 78 S&F 1Mm Thick Mild Steel, Plain, Black Sheet In Wall Cladding, Steel Gates And Similar Work, Cut To Size, Holes Punched; Including Round Headed Screws, Clout Nails Or Rivets And Fixed To Wood Or Steel Framing With Plain 40 Mm Lap Joints With Riveted Or Welded Seams, Including Bending Or Turning Up, Mitred Angles, Etc. As Required Complete All As Specified And Directed. 79 S&F Pressed Steel Frame Of Size 125X60mm Using 1.25Mm Thick Mild Steel Sheets For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plate, Etc, Including Making Good To Disturbed Suurfaces Complete All As Specified And As Directed. 80 S&F Pressed Steel Frame Of Size 105X60mm Using 1.25Mm Thick Mild Steel Sheets For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plate, Etc, Including Making Good To Disturbed Suurfaces Complete All As Specified And As Directed. 81 S&F Flush Door Shutter 35Mm Thick, Solid Core Construction With Block Board Core And Plywood Face Panels Commercial Type On Both Side With Decorative Face Veneer With Lipping / Frame To Match And Fitted To Steel Frame, Complete All As Specified And As Directed. 82 M&L Second Class Hardwood Plain Framed Panelled Shutter Factory Made 35Mm Thick ( Any Number Of Panels ) With Panels Of 12Mm Thick Veneered Particle Board, Medium Density Or 12Mm Thick Plywood Board, Bwr With Commercial Veneering On Both Faces And Fitted To Steel Frame, Complete All As Specified And As Directed. 83 M&L For 35Mm Thick Second Class Hard Wood Glazed And Skeleton Shutters, Factory Made, Open Rebated And Prepared To Receive Glass, Gauze, Etc. ( Without Sash Bars ) , Edges Of Framing Plain, Chamfered Or Rounded. Fitted With Cut And Mitred Beads For Securing Glass, Etc.; Sizes Of Me-Mbers Of Shutters As Specified In Ssr Part I, Section 8, Clause 8.24 ( A ) ; Supplied And Fitted To Chowkats Complete All As Specified And As Directed. 84 S & F Pvc Solid Door Frame Of Size 50 X 47 Mm Made Out Of 5 Mmthick Prelaminated Single Side Pvc Sheet Reinforced With Ms Square Tube Complete All As Specified And As Directed. 85 S & F 30 Mm Thick Factory Made Both Side Prelaminated Solid Panel Pvc Door Shutter Consisting Of Frame Made Out Of Ms Tube Of 19 Gauge Thickness And Size Of 19Mm X 19Mm For Stiles, Top And Bottom Rails, Treated With A Coat Of Metal Primer, Ms Frame Covered With Heat Moulded Prelaminated PvcC Channel For Stiles And Both Side Prelaminated Pvc Sheets For Top Rail, Lock Rail And Bottom Rail On Either Side And As Gap Insert For Top Rail And Bottom Rail; Stiles And Rails Feathered At Edges, Panelling Of Both Side Prelaminatedpvc Sheet To Be Fitted In The Ms Frame Welded / Sealed To The Stiles And Rails With Suitable Pvc Sheet Beading, And Joined Together With Solvent Cement And Fixing In Frame Complete All As Specified And Directed. 86 S&F Butt Hinges Of Size 100Mm, Extruded Aluminium Alloy With Galvanised Mild Steel Hinge Pin, Anodised And Fixed, Type B-21 Complete All As Specified And Directed. 87 S&F Aluminium Handle 150Mm Long ( Weight Not Less Than 120 Gram ) , Extruded Section, Fabricated Type, Anodised, Complete All As Specified And As Directed. 88 S&F Anodised Aluminium Window And Ventilator Shutters, Side Hung Type Without Sash Bars, Aluminium Sections Weighing 0.55 Kg / M Incl Necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings Such As Peg Stays 150Mm Long ( 1 No Each Shutter. ) . Hinges Type B-21 100Mm Long ( 2 No Each Shutter. ) Suitable Handle ( 1 No Each Shutter. ) Complete All As Directed By Engineer In Charge. 89 S&F Anodised Aluminium Frame For Doors, Windows, Ventilators With One Or More Rebates Including Jointing Cleat For Fixing Etc, Complete All As Specified And As Directed.Note :- ( A ) The Rates Include For Provision Of Pvc Protected Sheeting And Its Removal After Fixing The Frame Work. ( B ) Hinges, Shutters And Lugs Shall Be Measured And Paid For Separately. 90 S&F Sheet Glass 4.0Mm Thick, Ordinary Quality And Glazing, In Square Exc. 0.50 Sqm In Each Pane Of Aluminium Windows, Complete All As Specified And As Directed. 91 S&F Stainless Steel Wire Cloth. 0.36Mm Nominal Dia Of Wire And Average Width Of Aperture 1.40Mm And Fixed With Stainless Steel Wire Staples, Complete All As Specified And As Directed. 92 S&F In Repair Galvanised Mild Steel Wire Cloth, 0.56Mm Nominal Dia Of Wire And Average Width Of Aperture 1.18Mm And Fixed With Tinned Tacks, Or Galvanised Wire Staples Complete All As Specified And As Diected. 93 S&F Aluminium Anodised Security / Window Grill Of ( As Approved ) 4Mm Thick Made Out Of Anodised Aluminium Section Including Necessary Side Channel And Other Accessories Required For Fixing Etc, Complete All As Specified And As Directed. 94 Hacking Out Old Broken Glass ( Any Thickness, Size, Quality Or Description ) From Wooden Or Metal Frames, Glazed With Putty Or Fixed With Beads, Complete All As Specified And As Directed. 95 S&F Sheet Glass 4.0Mm Thick, Ordinary Quality And Glazing With Oil Putty In Square Not Exc. 0.50 Sqm In Each Pane Of Steel Windows, Complete All As Specified And As Directed. 96 S&F In Repair Aluminium Handle 150Mm Long ( Weight Not Less Than 120 Gram ) , Extruded Section, Fabricated Type, Anodised, Complete All As Specified And As Directed. 97 S&F Aluminium Barrel Tower Bolt 200Mm Long ( Weight Not Less Than 210 Gram ) , Extruded Section, Complete All As Specified And As Directed. 98 S&F Aluminium Barrel Tower Bolt 100Mm Long ( Weight Not Less Than 210 Gram ) , Extruded Section, Complete All As Specified And As Directed. 99 S&F 300Mm Long Aluminium Alloy, Anodised, Sliding Door Bolt With Hasp, Staple ( Bolt Type ) And Fixing Clips Of Sheet, Cast Or Extruded Sections And Fixing Bolts And Sliding Bolts Of Extruded Sections Or Cast-Aluminium Alloy And Fixed Complete All As Specifed And As Directed. 100 M&L Preparing New Or Previously Untreatedwood And Wood Based Surfaces Of Any Description, Not Otherwise Described, Over 10 Cm Width Or Girth And Applying Two Coat Of Synthetic Enamel Paint ( First Quality ) , Over A Coat Of Wood Primer Complete, Including Cleaning The Surface, All As Specified And As Directed. 101 M&L New Or Previously Untreated Steel And Iron Surfaces Of Any Description, Not Otherwise Described, Over 10 Cm Width Or Girth And Applying Two Coat Of Synthetic Enamel Paint ( First Quality ) , Over A Coat Of Zinc Chrome Red Oxide Primer Complete, Including Cleaning The Surface, All As Specified And As Directed. 102 Repairing Of Aluminium Door, Windows, Ventilators Shutter Fixed / Side Hung / Sliding Type Including Replacement Of Necessary Jointing Cleats, Glazing Clips, Rubber Neoprene Packing, Aluminium Snap Beading, Screws, Etc. And Repairing Of Locking Arrangement If Any, Complete All As Specified And As Directed.Note : Cost Of Materials Requiredfor Smooth Functioning Of Shutter Shall Deem To Be Included In The Quoted Unit Rate. 103 S&F In Repair Door Closer Aluminium ( Die Cast ) Body, Hydraulically Regulated, Designation No. 3, Universal Type, Suitable For Door Shutters Of 851Mm To 1000Mm In Width And Of Weight Between 61.00 To 80.00 Kilogram , Complete All As Specified And As Directed. 104 S&F In Repair Double Action Floor Spring Hydraulically Regulated Made Up Of Minimum 1.25Mm Thick Aluminium Alloy Sheet Foundation Box, Main Body With Stainless Steel Cover, Governing Pivot Made Of Brass, Other Parts Made Of Mild Steel Heavy Duty, Complete All As Specified And As Directed. 105 S&F In Repair For Mild Steel, Chromium Plated Curtain Rod 25Mm Dia ( As Approved ) , Complete All As Specified And As Directed. 106 S&F In Repair For Mild Steel, Chromium Plated Side Dome And To Be Fitted / Tightened For Curtain Rod 25Mm Dia With Screws, Complete All As Specified And As Directed. 107 S&F In Repair For Mild Steel, Chromium Plated Bracket ( Shaped ) , For Holdingfor Mild Steel, Chromium Plated Curtain Rod 25Mm Dia , Complete All As Specified And As Directed.
