|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III): 4 graded stone aggregate 40 mm nominal size). |
| 2 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 3 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed : All kinds of soil |
| 4 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil. |
| 5 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 7 | Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately) including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : Red sand stone slab 40 to 50 mm thick |
| 8 | Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 9 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 10 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 11 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece. |
| 12 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 13 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm nominal outer dia .Pipes. |
| 14 | Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 122mm long. Weighing not less than 99 gms. |
| 15 | Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigments etc., complete. |
| 16 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 17 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 18 | Providing and fixing soil, waste and vent pipes : Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. |
| 19 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe |
| 20 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 100 mm dia. Pipe |
| 21 | 100 mm Sand cast iron S&S as per IS - 3989 |
| 22 | 100 mm Sand cast iron S&S as per IS : 3989 |
| 23 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400mm. |
| 24 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia |
| 25 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 26 | Providing and fixing toilet paper holder : C.P. brass |
| 27 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 28 | Providing and fixing PTMT pillar cock of approved quality and colour . 15mm nominal bore, 125mm long foam flow. Weighing not less than 120 gms. |
| 29 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm |
| 30 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 200x10 mm |
| 31 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. |
| 32 | Add Cost Index 31.27% |
| 33 | Less 9.50% as per Delhi Govt. Circular |
| 34 | DRAIN: Supply and fixing of precast concrete Slit drain manufactured with M-30 grade of concrete & specifications. (a) 1000mm (length) x 415mm (width) x 415 mm (height), drain diameter 300mm, slit width 20mm. complete as per direction of engineer-in-charge. |
| 35 | 8 LAYER ACRYLIC FLOORING SYSTEM : Providing and laying 8 layer acrylic flooring system for badminton court approved by ITF. as per specifications mentioned below: Durocryl 8 Layer Acrylic Flooring System:1) 1 layer of Primer. 2) 1 layer of Resurfacer.3) 4 layer of Cushion4) 2 layers of color coat. |
| 36 | Providing and laying15mm thick synthetic jogging track EPDM (9mm SBR Crumb Rubber as track bottom Cushion Layer + 6mm EPDM Colour Granules top layer) of approved make COLOR SPACE/COLORPLAY/BSGNOVAL/BASForequivalent.EPDM Granules shall have following minimum properties (i) Polymercontent>22%, (ii) Hardness of 55-65 Shore A (per ASTMD 2240); (iii) Tensile Strength of > 5 MP a (per ASTMD 412); (iv) Elongation > 500% (as per ASTMD412); (v) Density of 1.6 kg/cum (per ASTM D792) , (vi) High UV rating of 3-5 on grayscale, (vii) VOC less than 3.0.0gm/l (viii) Combustibility less than 40 mm /m; (ix) Anti-Microbial & Anti-Fungal Tested material, & shall belaid in three layers. (1) First step shall bethe application of single component Polyurethane based primer coating Layer; PU binder shall have aspecific gravity of 1.05; the appearance of clear pale yellow and viscosity of 350-2900 cps and shall be from the original manufacturer from the list of approved makes 2. The second layer shall be an impact attenuating cushion layer of 9mm thick black crumb rubber/SBR adhered with a polyurethane binder and PU binder shall have a specific gravity of 1.05; the appearance of clear pale yellow and viscosity of 350-2900 cps and shall be from the original manufacturer from the list of approved makes of to form a resilient porous layer. Crumb rubber /SBR shall be mixed with a minimum of 14%-16% % of single-component PU base binder so as to ensure that PU binder provides 100% coating of the SBR/crumb rubber particles. The third step shall belaying a 6mm EPDM GRANULES to player with a minimum 18% binder of single component polyurethane and shall provide 100% coating of the EPDM granules particles. Design on the base top layer by a specialized team of installers according to the specification of approved material and shade. The documentary evidence has to be produced for the procurement of material for the manufacturer’s test certificate. |
