|
| 1 | Electrical Works. |
| 2 | Dismantling of defective & damaged existing sodium light from double arm ST pole installed on central verge of Pakwada-Dingerpur road including safely shifting to store at SEZ Moradabad. |
| 3 | Supply & fixing 90 W LED street light fitting having die cast aluminium body and diffuser with driver set confirming to IP 66 protection complete coverage with five year warrenty against any defects complete in all respect. (Minimum CAT-AA) Havells/Bajaj/crompton/wipro make |
| 4 | Supply & fixing of street light junction box made of SMC material complete with terminal & cable gland. |
| 5 | Supply & fixingof 0.5 Amp to 5 Amp. SP MCB (10KA) C Curves in box with suitable rail channel. |
| 6 | Supply & erection of \"D\" clamps of 38 mm x 6 mm flat iron for wall /roof type service bracket with bolts, nuts etc. complete in all respects including painting with aluminum paint . |
| 7 | Supply and fixing of anticlimbing device fabricated from G.I. flat of 25mmx6mm size in a sape of ring of the pole size, heving G.I flat pointed fins of length 225 mm in 8 nos. and also barbed wire in 200 mm length above the said ring including material. |
| 8 | Suppy,laying & drawing of3x1.5 Sq mm PVC insulated copper cable for Street/flood lights connection in existing pipe/surface/air as required including cost of material, men and T&P. |
| 9 | Supply and laying of 16 sq.mm 2 core aluminium conductor PVC insulated, unarmoured, served, double sheathed cable 1100 V grade pole to pole (Havell\"s/Polycab/Grandley /Glostar) |
| 10 | Supply and erection of steel tubular pole 410 SP-63 12M long. 277 Kg complete inclusive hardware and ordinary pole fittings with Painting of two coats of aluminum and one coat of red oxide paint including foundation work with 1/6th of overall length of pole below ground level with 45cm dia cement concrete with 45cm above the ground leval. The foundation of underground will not be less than 20cm thick layers of cement concrete in the ration of 1:3:6 (Cement :coarse sand : over burnt brick ballast/stone ballast), The brick ballast/stone ballast will be used of 1.25cm size with stone pad of 30x30x7.5cm at the base. as per direction of E/I of work/site including all T&P, men and material for proper completion of work. The bottom section of pole should be galvanized as per PVVNL. |
| 11 | Supply and erection of stay of LT lines for ST pole with GI anchor plate (152x152x6mm) stay rod (16mm dia x 1.85 m long) GI stay below (16mm dia rod , thriple, double stay tightener, stay insulator, clampas & stay wire (GS 7/3 .15mm) including grouting in 1:4:8 ratio of cement corcente using coars sand, over burnt brick ballast as per direction of engineer in charg complete in all respect. |
| 12 | Supply & fixingbracketsmade from32mm dia,1.20M long GI bend pipe with 02 nos. clamp of 50x6mm MS Flat suitable for fixing street light on ST pole. |
| 13 | Supply & laying of 3x16 sq.mm Arial bunch conductor with supporting cum nutral wire including cost of all material,men and T&P. |
| 14 | Supply & fixing insulated piercing connector suitable for ABC cable including cost of material,men and T&P. |
| 15 | Supply & fixing tension/section/dead end fitting suitable ABC cable complete in all respect. |
| 16 | Supply & fixing MS clamp made out from 50x6mm MS clamp for fixing shackle insulator/eye bolts ST pole. |
| 17 | Supply and laying of 16 sq. mm 4.0 core standed aluminium conductor insulated PVC bedded galvanised flat steel strip armoured cables confirming to IS 7098, 11 KV garde Through HDPE Pipe/GI Pipe/in Air. |
| 18 | Supply and laying of 25 sq. mm 3.5 core standed aluminium conductor insulated PVC bedded galvanised flat steel strip armoured cables confirming to IS 7098, 11 KV garde Through HDPE Pipe/GI Pipe/in Air. |
| 19 | Supplying and laying of 50 sq. mm. 3.5 core aluminium conductor PVC insulated armoured, served, sheathed cable 1100 Volts grade at a depth of 750 mm. below ground level over a cushion of 75 mm. thick sand alround and protected with burnt bricks on sides and on top. |
| 20 | Supply and fixing 16 Sq. mm brass nickle plated compression gland for following sizePVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. |
| 21 | Supply and fixing 25 Sq. mm brass nickle plated compression gland for following sizePVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. |
| 22 | Supply and fixing 50 Sq. mm brass nickle plated compression gland for following sizePVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. |
| 23 | Supply and fixing 16 Sq. mm plain or pin type copper tin plated cable socket ( lug ) to the following size cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 24 | Supply and fixing 25 Sq. mm plain or pin type copper tin plated cable socket ( lug ) to the following size cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 25 | Supply and fixing 50 Sq. mm plain or pin type copper tin plated cable socket ( lug ) to the following size cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 26 | Supply & Laying of63 mm HDPE pipe ISI marked along with all accessories like socket,bend,couple etc. confirming to IS 14930 Part II complete with fitting and cutting,jointing etc direct in ground (750 mm below ground level) including excavation and refilling the treanch. including cost of material,labour and T&P. |
| 27 | Supply & laying of 63mm DWC /HDPE pipe by horizontal manual drilling at road crossing including cost of all material, men and T&P. |
| 28 | Supply & Laying of90 mm HDPE pipe ISI marked along with all accessories like socket,bend,couple etc. confirming to IS 14930 Part II complete with fitting and cutting,jointing etc direct in ground (750 mm below ground level) including excavation and refilling the treanch. including cost of material,labour and T&P. |
| 29 | Supply & fixing 40 TPN capacity of automatic street light cubical panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors,HRC fuses, isolating switch metering instrument & instrument box with CT\"s etc. |
| 30 | S/B of 40 mm dia x 4.5 mtr. long G.I. pipe vertically for earthing having 12 mm dia. Holes spaced 75 mm apart drilled upto 2 mtr. from the bottom complete with earthing lead of no.6 to 8 SWG GI wire in G.I.pipe upto appron upto switch board 30 cm square box with hinged cover masonary enclosure. Funnel of top, alternate layers of charcoal and salt at least 150 mm thick alround etc. as per direction E/I complete in all respect. |
| 31 | Providing & fixing 25mm x5mm G.I. earth strip on surface or in recess including cost of GI saddle/Al. Alloy/cadmium/PVC fastener etc.plated iron screw etc. as required for connections. |
| 32 | Supply & fixing 50mm dia GI pipe B class for climbing up the cable of 16/25/50 Sq. mm from ground to overhead S/L line including all acessories material,labour and T&P required for proper completion. |
| 33 | Supply & fixing MS clamp made out from 50x6mm MS flat for securing 50mm GI Pipe/HDPE with ST pole. |
| 34 | Supply and erection of steel tubular pole 410 SP-55 11M long. 227 Kg(11 KV Line ) complete inclusive hardware and ordinary pole fittings with Painting of two coats of aluminum and one coat of red oxide paint including foundation work with 1/6th of overall length of pole below ground level with 45cm dia cement concrete with 45cm above the ground leval. The foundation of underground will not be less than 20cm thick layers of cement concrete in the ration of 1:3:6 (Cement :coarse sand : over burnt brick ballast/stone ballast), The brick ballast/stone ballast will be used of 1.25cm size with stone pad of 30x30x7.5cm at the base. as per direction of E/I of work/site including all T&P, men and material for proper completion of work |
| 35 | Supply and erection of stay of HT lines for ST pole with GI anchor plate (152x152x6mm) stay rod (16mm dia x 1.85 m long) GI stay below (16mm dia rod , thriple, double stay tightener, stay insulator, clampas & stay wire (GS 7/3 .15mm) including grouting in 1:4:8 ratio of cement corcente using coars sand, over burnt brick ballast as per direction of engineer in charg complete in all respect. The bottom section should be galvanized as per PVVNL. |
| 36 | Supply and laying of 70 sq. mm 3 core standered aluminium conductor XLPE (Cross linked polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. The armouring of cable shall be properly connected with earth conductor by clamps etc. |
| 37 | Supply & laying of 110-120 mm DWC /HDPE pipe by trenchless machine on pucca road including cost of refilling pit with bitumus/concrete all material, men and T&P. |
| 38 | Supply & Laying of 100mm dia size GI pipe B class for climbing up the cable of 70 Sq. mm, from ground to overhead S/L line and road crossing under existing 33 KV line including all acessories material,labour and T&P required for proper completion. |
| 39 | Suply & fixing outdoor type 11 KV fuse set complete with insulator & other acessories.(Relco/Azad/Rama/Other standered make as approved by UPPCL) |
| 40 | Supply & fixing push on type heat shrinable jointing kit suitable for 3 core 120 sq. mm 11 KV HT cable outdoor type including all material,labour and T&P required for proper completion of work. |
| 41 | Supply,sagging,jointing and binding of ACSR Weasel conductor including cost of aluminium tap,binding wire and jointing sleaves etc. complete in all respect. |
| 42 | Supply & fixing Jointing sleeve for Insulated ACSR Weasel conductor including cost of all material, compress machine, man and T&P. |
| 43 | Supply & laying of two parallel length of 6 SWG Earth wire as guard wire along the span and across the span at an interval of 5m for cross lacing complete as direction by engineer in charge including cost of all materialman and T&P. |
| 44 | Supply & fixing clamp suitable for securing the channel & cross arm with the hole made out of MS flat 50x6mm including all bolts,washer,T&P,mem and material complete in all respect. |
| 45 | Supply & fixing 11 KV originating/terminating pole fitting including all T&P,men and material for proper completion of work as per SIDC Schdule No. E03.01 |
| 46 | Supply & fixing of 11 KV pin with insulator on channel arm fixed on ST/DP including cost ofall nuts, bolts, washers, T&P ,men and material. |
| 47 | Supply & fixing 11 KV disc insulator with galvanised insulator fitting,ball and socket type complete with strain clamps,bolts,nuts,washer etc including cost of material,men and T&P. |
| 48 | Supply & fixingM.S. Top channel of 125x65x2240 mm including cost ofholding clamps and material men & T&P. |
| 49 | Supply & fixingM.S. droper channel of 100x50x2028mm including cost ofholding clamps and material men & T&P. |
| 50 | Supply & fixing Danger board fabricated from 10 guage M.S. sheet as per IES/UPPCL |
| 51 | Supply & fixing straight through jointing kit heat shrinkable type suitable for 70 sq.mm XLPE 11 KV HT Cable including all material, men and T&P.(Densons/3M/Raychem) |
| 52 | Hiring charge of fault locating machine(for high pressure test) of 11 KV U/G cable including excavation & restroation at fault location complete in all respects. |
| 53 | Repairing of 63 KVA,11/0.4 KV T/F including changing HV/LV coil,bushing,gaskits, filling T/F oil (fresh)painting & associated material includingbuy back of old scrap material complete with PVVNL technical specification with men and T&P. |
| 54 | Dismantling ,Cartage & re-erection of 63 KVA,11/0.4 KV T/F including cost of cartage, loading, unloading men and T&P. |
| 55 | Cleaning & spray painting of ST bend pole and power ST pole with one coat of red oxide primer and two coat of alum. Paintper direction of Engineer incharge including cost of all material, men and Hydraulic crane,other T&P.(Burger/Nerolac/Asian make) |
| 56 | Supply & fixing 3-Phase Power Contractor ML-3 type or equel for Automatic Street & High Mast Control Panel in cluding cost of Connection, men and T&P. (Only for AMC as directed by Engineer in charge.) |
| 57 | Supply & fixing Astronomical time switch L&T/Siemens/C&S or equel brand including cost of connection, material, men and T&P.(Only for AMC as directed by Engineer in charge.) |
| 58 | S&F of 63 amp. 4 pole MCB (10KA cat B) for control panel complete in all respects.(Only for AMC as directed by Engineer in charge.) |
| 59 | Supply and making straight through joint with cast resin compound including ferrules and other joints materials for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor 25/35/50 sq.mm 3.5 core cable of 1100 v grade complete |
| 60 | Providing new street lights pole earthling of an existing pole by inserting MS Rod 20x2500mm in vertically ground level and connecting the pole with the help of 6 SWG GI wire including cost of all material, men and T&P. |
| 61 | Cost of material spares, wire, fuses, small accessories, alum. Lug up to 16 sq.mm , small cable gland , insulation tap,plastic tie, screw, nut & bolts, old cloth, cleaning spray and other small associated required for up-gradation work etc.(Only for AMC as directed by Engineer in charge.) |
| 62 | Trimming of tree branch around the street light pole/ST pole/Central Varge for proper illumination& proper disposal of tree branch collecting on trolly or similer moving item including cost of men, trolly, T&P etc. |
| 63 | Hiring Charge of 80-100 feet expandable street light repairing hydraulic lift, capacity 300 Kg including cost of operator, mounting vehicle and fuel etc. |
| 64 | Dismantling of damaged ST pole and cartage to store including cost of cartage,men and T&P and shifting to store charge. |
| 65 | Strengthen of ST pole foundation by providing new concreting including broken of weak foundation,excavation, surface finishing and painting ,cost of all material,men and T&P. |
| 66 | Dismantling & re-grouting of street light/Steel tubler (upto 12 Mtr long) Tilt/sick bend pole in 1:3:6 ratio cement concrete with stone pad includingstrengthening of pole by providing additional 04 Nos. support of65x65x6mm or higher sizeMS angle in suitable length with the help of welding/cutting as per technicalspecification.(Only for AMC as directed by Engineer in charge.) |
| 67 | Painting letters(Pole No.) 2.5cm up to 8.0 cm size complete on Street light Pole/Panel/Other electrical properties under UPSIDA including cost of all material, men and T&P. |
| 68 | Providing operating cum maintenance staff of the entire street light networkfor routine maintenance of road lighting system,administrative,site offic and staff colony etc. including dismantling & re-fixing of other street lights of UPSIDA with there travelling expenses etc. Staff only for AMC as directed by Engineer in charge.) (Electrician-2 Nos.+ Helper-3 Nos. ) |
| 69 | Fabrication, supply and fixing of work information board in M.S. frame made by 50mm dia Square Pipe of Stainless steel grade SS-304 & 16 mm thick base plate with back supporting of bracing by MS flat of 25x6mm and 2.85 Mtr long supporting leg made from 65mm pipe SS-304 grade with proper grouting arrangement. The board should be Retro reflective type in green color with white letters as required and shall be fixed at a height of 1.2 Meter from ground by providing 0.45x0.45x0.60 Mtr cement concrete stone pad as per drawing enclosed. |
| 70 | Buy Back of Old/Defective 150W/250W HPSV luminaries complete fiiting as is as where condition. |
| 71 | Buy Back of Defective/Damage iron/steel pole. |
