|
| 1 | AIR CONDITIONER Taking out existing unserviceable compressor sealed unit from window/splittype air conditioner 1.5 / 2.0Ton capacity including removal of unserviceable strainer filter etc. complete all as specified and directed by Engineer-in-charge. |
| 2 | Supply, fixing and connecting of new compressor sealed unit of capacity 1.5 Ton for window/split type suitable for air conditioner of any make/as per existing type including replacement of foundation bolts, rubber pad, strainer capillary tubes, suction and discharge pipe line, wiring kit, vacuuming the system, supply and charging Gas (R-22/R-134A), detection of leakage etc., brazingand testing to achieve proper cooling effect complete all as specified and directed by Engineer-in-charge. |
| 3 | All as per srl item No. 02 here-in-before but of 2.0 Ton capacity. |
| 4 | M&L forleakdetection by nitrogen pressure test in refrigerant system for split/ window type AC 1.5 TR capacity, cutting brazing and making leak-proofthe gas system, cleaning, vacuum thegas system and charging suitable gas of any type as required quantity to achieve desire cooling including installation at site and testing on full load for 24 hours complete all as specified an directed. (Note:- Additional gas required will measured & paid separately under relevant item as supply and charging.) |
| 5 | All as per srl item No. 04 here-in-before but of 2.0Ton capacity. |
| 6 | Taking down blower motor from air conditioner of 1.5 / 2.5 Ton capacity andmake / and fixing as per existing type and replacing the new motor, single phase, 200/230 volt, 50 Hz, 1/5 HP capacity,ISI Marked in the same position, testing etc complete all as specified and directed by Engineer-in-Charge. |
| 7 | Supply and fixing, in replacement, of running capacitor (36 mfd) suitable for air conditioner of any make / type / capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 8 | Supply and fixing, in replacement, of starting capacitor (100/120 mfd) suitable for air conditioner of any make / type / capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 9 | Supply and fixing, in replacement, of thermostate switch of temperature range of 16°C to 30°C suitable for air conditioner of any make / type / capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 10 | Supply and fixing, in replacement, of grill with knob made of fiber plastic body suitable for window type AC of any make / type / capacity complete as per existing make all as specified and directed by Engineer-in-Charge. |
| 11 | Supply and fixing in repair of factory made wall mounted/floor mounted type AC outdoor unit stand of superior quality ISI Marked material duly coloured suitable for AC of 1.5/2.0 TR capacity complete all as specified and directed. |
| 12 | Supply and fixing in replacement, of starting relay suitable for air conditioner of any make / type / capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supplyand fixing in replacement ofplastic filter for window type AC 1.5/2 ton capacity complete as as directed. |
| 14 | Supply and fixing in replacement of fan motor ISI markedfor indoor unit of split type air conditioner of any make / type and capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 15 | Supply and fixing in replacement of fan motor ISI markedfor outdoor unit of split type air conditioner of any make / type and capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 16 | Repair/ replacement of electronic control circuit card suitable for air conditioner of any make / type and 1.5 / 2.0 ton capacity including making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 17 | M&L for servicing of split/ window type air conditioner of capacity 1.5/2.0 Ton of any make and type by replacing unserviceable compressor and other parts from the machine including charging of refrigerant gas and changing of wiring with proper size PVC insulated wires as directed, by replacing Air Filter,Oiling of Blower,Condensor Fan Motors ,replacement of Bushes 2 Nos for fan motor ,cleaning of condensor coil by high pressure water & cleaning liquid, complete as directed,Installing the Air conditioner at location where directed after proper repair and testing complete at site as per the satisfaction of Engineer-in-Charge.(Note : M&L for replacement of compressor, Spare Parts and Gas shall be measured and paid separately under relevant items. |
| 18 | Material and Labour for scraping of old paint by wire brush frombody of window type AC and applying base material for smooth surface and applying2 coat of synthetic enameled spray paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. |
| 19 | Supplyand fixing in replacement ofplastic filter for split type AC 1.5/2 ton capacity complete as as directed. |
| 20 | Supply and fixing in replacement of cooling coil 1.5 ton /2 ton split type AC make as directed by Engr-in-Charge |
| 21 | Supply and fixing in replacement sheet metal enclosure industrial type complete plug socket and plug top and earth plug complete with SP MCB 20 Amp complete all as specified and directed Make Havells/Ind Asian/Legrad |
| 22 | Supplyand replacement of fan blade suitable forsplit type/ window ACcapacity 1.5/2.0 as per sample all as spacified and directed. |
| 23 | S&F in replacement running capacitor 50+6 MFDsuitable for 2.0 ton Air Conditioner split type complete all as directed. |
| 24 | S & F in replacement of plug top3 Pin 5 Amp 240 volts all as specified and directed. |
| 25 | S & F in replacement of plug top3 Pin 15 Amp 240 volts all as specified and directed. |
| 26 | RefrigeratorTaking out unserviceable compressor from refrigerator of capacity 165 to 310 ltr of any make by un-screwing from base plate after disconnecting all electrical and suction / discharge pipe connections complete and providing all electrical connections to respective terminals including changing of unserviceable connecting wires as per the existing charging of refrigerant gas as per requirement to achieve proper cooling effect and testing on completion complete all as specified and as directed.(Note : M&L in replacement of compressor (sealed unit), Gas and Parts required for satisfactory repair shall be paid and measured separately under relevant items. |
| 27 | Supply, fixing and connecting of new compressor sealed unit suitable for refrigerator of capacity 320/ 310/ 270 ltrs and any make/type, medium temperature range, including replacement of foundation bolts, rubber pad, strainer, capillary tubes, suction and discharge pipe line,vacuuming the system, supply and charging Gas (R-22/R-134A), detection of leakage etc., brazing and testing to achieve proper cooling effect complete all as specified and directed by Engineer-in-Charge. |
| 28 | All as per srl item No. 27 here-in-before but for capacity 180 ltrs. |
| 29 | M&L forleakdetection by nitrogen pressure test in refrigerant system of Refrigerator of any capacity and make, by cutting brazing and making leak-proofthe gas system, cleaning, vacuum the gas system and charging suitable gas of any type as required quantity to achieve desire cooling including installation at site and testing on full load for 24 hours complete all as specified an directed. (Note:- Supply and charging additional gas required willmeasured & paid separately under relevant item.) |
| 30 | Supply and fixing in replacementof starting relay and overload protector ISI marked suitable for refrigerator of any make/ type/capacity including making connection complete all as specified and directed by Engineer-in-Charge or equivalent make in market. |
| 31 | Supply and fixing in replacementof thermostat switch with knob ISI marked suitable for refrigerator of any make/type/capacity including making connection complete all as specified and directed by Engineer-in-Chargeor equivalant make in market |
| 32 | Supply and fixingin replacement of cabinet bulb with door switch ISI marked suitable for refrigerator of any make/type/capacity including making connection complete all as specified and directed by Engineer-in-Charge. |
| 33 | Supply and fixingin replacement of vegetable tray of single/two pieces type suitable for refrigerator of any make/ type/ capacity complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixingin replacement of crisper tray suitable for refrigerator of any make/ type/ capacitycomplete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fixingin replacement ofbottle shelf/ egg shelf suitable for refrigerator of any make/ type/ capacitycomplete all as specified and directed by Engineer-in-Charge. |
| 36 | Supply and fixing in replacement ofmagnet type door gasket suitable for refrigerator of any make/ type/ capacitycomplete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply and fixing in replacement of toughened glass self/cover for vegetable tray suitable for refrigerator of any make/type/capacity complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing in replacement of evaporator coil ISI marked suitable for refrigerator of any make/type/capacity including making connection complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fixing in replacementofcondenser coil ISI marked suitable for refrigerator of any make/type/capacity including making connection complete all as specified and directed by Engineer-in-Charge. |
| 40 | S&F in replacement fan motor for refrigerator 270/ 300/ 310 ltrs capacity complete as per existing make all as specified and directed |
| 41 | S & F in replacement freezer with cooling/pipe capillary or compressed freezer complete for refrigerator 310/ 300/ 270 Ltr as per existing make complete all as specified and directed. |
| 42 | Supply and fixingin replacement PC Board for 270 to 310 ltr refrigerator suitable make as perdirect by Engr-in-Charge. |
| 43 | Supply and fixingin replacement of timer for refrigerator ISI markedcomplete all as specified and directed. |
| 44 | WATER COOLER Material and Labour for taking out existing unserviceable compressor sealed unit from the water cooler of any make/type/capacity including removing of all other unserviceable parts / spares such as strainer filer, capillary tube, suction / discharge pipe, thermostat switch, float valve, push cook running capacitor, starting capacitor, over load relay etc complete all as specified and directed by Engineer-in-Charge. |
| 45 | Supply, fixing and connecting of new compressor sealed unit suitable for water cooler of any make/type and 150 ltr ,120 ltr/ hr cooling capacity, medium temperature range, including replacement of filter and making connection, vacuuming the system, supply and charging Gas (R-22/R-134A/R-410A), detection of leakage etc., brazing and testing to achieve proper cooling effect complete all as specified and directed by Engineer-in-Charge. |
| 46 | All as per srl item No 45 here-in-before but water cooler of any make/type and 40/60, 40/80 ltr/ hr cooling capacity. |
| 47 | Material & Labourforleakdetection by nitrogen pressure test in refrigerant system of water cooler of any make/type but of 150/120 ltrs / hr cooling capacity, by cutting, brazing and making leak-proofthe gas system, cleaning, vacuum the gas system and charging suitable gas of any type as required quantity to achieve desire coolingincluding installation at site, testing of water cooler on full load for 24 hours continuously complete all as specified an directed. (Note:- Supply and charging additional gas required willmeasured & paid separately under relevant item) |
| 48 | Material & Labour for Material & Labourforleakdetection by nitrogen pressure test in refrigerant system of water cooler of any make/type but of 40/60 ,40/80ltrs/ hr cooling capacity, by cutting, brazing and making leak-proofthe gas system, cleaning, vacuum the gas system and charging suitable gas of any type as required quantity to achieve desire coolingincluding installation at site, testing of water cooler on full load for 24 hours continuously complete all as specified an directed. (Note:- Supply and charging additional gas required willmeasured & paid separately under relevant item) |
| 49 | Supply and fixing in replacementoffan motor ISI marked in existing water cooler of any make/type/capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply and fixing in replacementoffan motor blade ISI marked PVC/metalic type in existing water cooler of any make/type/ capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply, fixing and connecting of running capacitor30 Mfd ISI marked in existing water cooler of any make/type/capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply, fixing and connecting of starting capacitor 60/80 mfd ISI marked in existing water cooler of any make/type/capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply andfixing in replacementand connecting of thermostat switch ISI marked in existing water cooler of any make/type/capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing in replacementand connecting of chromium plated push cock tape, in existing water cooler of any make/ type/ capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supplyandfixing in replacementand connecting of PVC heavy duty waste water pipe of 32/40 mm size and min 1.5 mtr long, including repair of waste water tray in existing water cooler of any make/type/capacity including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply and fixing in replacement of damaged water tank from water cooler of any make/type but of capacity 120/150 ltr and supply & fixing new stainless steel water tank ISI marked including all fixing accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 57 | All as per srl item No 56 here-in-before but water cooler of any make/type but of 40/60,40/80 ltr capacity. |
| 58 | Supply and fixing in replacementof evaporator coil ISI marked suitable for water cooler of any make/type/ capacity including all fixing accessories and making connection / detecting leakage and gas charging etc complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply and fixingin replacement of condenser coil ISI marked suitable for water cooler of any make/type/capacity including all fixing accessories and making connection etc complete all as specified and directed by Engineer-in-Charge. |
| 60 | Material and labour for repairing to base/stand of water cooler of any make/type/capacity including welding of MS/GI sheet 16 SWG of suitable size to fill up rusted patches, grinding and applying base material for smooth surface and applying two coat of synthetic enameled spray paint of existing colour over one coat of primer etc complete all as specified and directed by Engineer-in-Charge. |
| 61 | Material and labour for scraping of old paint / rust etc by wire brush frombody of water cooler of any make/type/capacity and applying base material for smooth surface and applying two coat of synthetic enameled spray paint over one coat of primer after denting etc complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply and fixing in replacement for capacitor 4.0/0 Mfd for, water cooler and desert cooler fan motor complete all as specified and directed by Engineer-in-Charge. Make :- Tibcon/ Asian/ Sharda. |
| 63 | DESERT COOLER:Supply, fixing and connecting new fan motor, single phase 230 volt 50 Hz copper wounded three speed suitable for desert cooler of 500 mm sweep size etc completeincluding dismantling and removing of existing unserviceable fan motor with blades from the desert cooler of any make/type/capacity including removing of all fixing accessories etcall as specified and directed by Engineer-in-Charge. |
| 64 | Supply, fixingin repair submerisble type tullu pump for desert cooler of capacity 1/85 HP, single phase 230 volt 50 Hz copper bound etc incl fixing accessories complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing in replacement of wooden wool pads including wire mesh suitable for 4000/5000 cuf/M complete all as specified and directed by Engineer-in-Charge. |
| 66 | Material and labour for scratching of old paint and rust by wire brush and applying two coats of spray paint of off white / gray colour over one coat of primer ( red oxide ) including black bitumen paint at in side body of desert cooler complete all as specified and directed by Engineer-in-Charge. Note :- The compressor and spray machine shall be arranged/brought by contractor at E/M yard and no extra cost shall be paid to the contractor in this effect. |
| 67 | Supply and fixing in replacement of selector switch single phase 230 volts, ISI marked complete all as directed by the Engineer-in-Charge. |
| 68 | Supply and fixing in replacement of side grill made out of 22 SWG gauge GI sheet including applying two coats of spray paint of off white / gray colour over one coat of primer ( red oxide ) suitable for desert cooler of capacity 4000/5000 cuf/Min complete all as directed by the Engineer-in-Charge. |
| 69 | Supply and fixing in replacement of top part of desert cooler made out of GI sheet of 20 SWG gauge including applying two coats of spray paint of off white / gray colour over one coat of primer (red oxide) suitable for desert cooler of capacity 4000/5000 cuf/Min complete all as directed by the Engineer-in-Charge. |
| 70 | Supply and fixing in replacement of bottom part of desert cooler made out of GI sheet of 20 SWG gauge including applying two coats of spray paint of off white / gray colour over one coat of primer ( red oxide ) and black bitumen paint at inner surface suitable for desert cooler of capacity 4000/5000 cuf/Min complete all as directed by the Engineer-in-Charge. |
| 71 | Supply and fixing in replacement offront grill made out of GI sheet of 20 SWG gauge including applying two coats of spray paint of off white / gray colour over one coat of primer ( red oxide ) suitable for desert cooler of capacity 4000/5000 cuf/Min complete all as directed by the Engineer-in-Charge. |
| 72 | Supply and fixing in replacement of factory made metalic/PVC fan blade suitable for desert cooler of capacity 4000/5000 cuf/Min complete all as directed by the Engineer-in-Charge. |
| 73 | Supply and fixing in replacement of PVC pipe of 15 mm dia with water PVC distribution and PVC elbow complete all as specified and directed by the Engineer-in-Charge. |
| 74 | Supply and fixing in replacement of legs for fan motor made out for 18 SWG MS platecomplete all as specified and directed by the Engineer-in-Charge. |
| 75 | Supply and fixing in replacementPVC connection 15 mm size with PTMTnuts of length 600mm complete all as specified and directed by the Engineer-in-Charge. |
| 76 | Supply and fixing in replacement ball brassvalves, high pressure, with polythene float and flynut complete , screwed for iron pipe or brass ferrule bore of pipe 15mm dia complete as per existing make all as specified and directed. |
| 77 | Supply and fixingin replacement of PVC connection 15 mm dia and 300mm long with brass nut and washer for desert cooler ISI marked all as specified and directed. |
| 78 | Supplying and fixing in replacement MS framed works as in frame of desert cooler of angle or other section with gusset plates, rails, braces etc , including drilling and grouting in wall complete all as specified conforming to Fe290 Gde E-165. |
| 79 | Supply and fixingin replacement stop valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for 15mm bore pipe/ unionscomplete all as specified |
| 80 | Supply and fixingin replacement 15mm bore float/ ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 142gms) PVC with float complete all as specified |
| 81 | Supplyand fixing in replacement of desert cooler body made of20 guage PGI Sheet suitable for evaporative type desert cooler of size 67x67x87 cm including side panel-03 nos and front grill with 20 guage PGI sheet and water tank height 20 cm and grill with fins, electriclal wiring and connection with on/off switch piano type with distribution PVC cable 3 core 23/0.0076-3m with top plug 5 Amp-01 No,15mm flot vlave-01 including duly painted complete body internaly and externaly and all side panel inner and outer side with 2 coat sythetic enamel paint of approved colour over a coatr of red oxide primer complete all as specified and directed. |
| 82 | M&L for rewinding of fan motor for desert cooler upto 500mm sweep with exiting size/guage super enanmelled copper winding wire insultaing material, replacement of bushes, varnising drying complete including taking out and refixing and testing in position complete all as specified and directed |
| 83 | Supplyand fixing in replacement of desert cooler body made of20 guage PGI Sheet suitable for evaporative type desert cooler of size 67x67x87 cm including side panel-03 nos and front grill with 20 guage PGI sheet and water tank height 20 cm and grill with fins, electriclal wiring and connection with on/off switch piano type with distribution PVC cable 3 core 23/0.0076-3m with top plug 5 Amp-01 No,15mm flot vlave-01 including duly painted complete body internaly and externaly and all side panel inner and outer side with 2 coat sythetic enamel paint of approved colour over a coatr of red oxide primer complete all as specified and directed. |
| 84 | VOLTAGE STABILIZER: Material and labour for stripping up of voltage stabilizer and replacing of main transformer 5 KVA capacity with super enameled copper wirefor input variation between 140 volt to 280 volt and output volt of 230 volts, 50 Hz including replacement of main circuit and testing etc complete all as specified and directed by Engineer-in-Charge. |
| 85 | All as per srl item No 84 here-in-before but voltage stabilizer of 4 KVA capacity. |
| 86 | All as per srl item No 84 here-in-before but voltage stabilizer of 3 KVA capacity. |
| 87 | All as per srl item No 84 here-in-before but voltage stabilizer of 2 KVA capacity. |
| 88 | Supply and fixing in replacement of old voltmeter 0-300 volt range complete all as specified and directed by the Engineer-in-Charge. |
| 89 | Supply and fixing in replacement of indicator lamp Neon type green / red etc complete all as specified and directed by the Engineer-in-Charge. |
| 90 | Supply and fixing in replacement of relay 24 volt, 25 Amps, ISI marked suitable for voltage stabilizer of any type/make/capacity etc complete all as specified and directed by the Engineer-in-Charge. |
| 91 | Supply and fixing in replacement of electronic circuit ISI marked suitable for voltage stabilizer of any type/make/capacity etc complete all as specified and directed by the Engineer-in-Charge. |
| 92 | Supply and fixing in replacement of copper wire, 3 core, flexible type of size 40/0.0076 etc complete all as specified and directed by the Engineer-in-Charge. |
| 93 | Supply and fixing in replacement of 3 pin Iron clad metal top and plug 15 Amp 240 volts all as specified and directed . |
| 94 | Supply and fixing in replacement of copper wire, 3 core un-sheathed, flexible type of size 1.5 sqmm etc complete all as specified and directed by the Engineer-in-Charge. |
| 95 | Supply and fixing in replacement of copper wire, 3 core,un-sheathed flexible type of size 2.5 sqmm etc complete all as specified and directed by the Engineer-in-Charge. |
| 96 | Supply and fixing in replacement of voltage stabilizer, copper wound of 4 KVA capacity digital display type having I/P correction range of 140- 280 volt complete all as specified and directed by Engineer-in-Charge. |
| 97 | Supply and fixing in replacement of voltage stabilizer, copper wound of 3 KVA capacity digital display type having I/P correction range of 140- 280 volt complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply and charging gas R-134a in 450 gm tin complete all as specified and directed. |
| 99 | Supply and charging gas R-22 in 450 gm tin complete all as specified and directed. |
| 100 | Supply and charging gas R-410A in 450 gm tin complete all as specified and directed. |
| 101 | Supply and fix in replacement MCB single pole 25 Amps 240 volts, 50 Hz, 10 KA\"C\" series in existing distribution board. |
| 102 | Supply and fix in replacement MCB single pole and neutral 32 Amps 240 volts, 50 Hz , 10 KA \"C\" series in existing distribution board. |
| 103 | REPAIR TO DEEP FREEZER:Taking out compressor sealed unit from deep freezer any capacity and make including removal of unserviceable parts/ spares, such as over load protector, strainer capillary tube etc complete all as specified and directed by Engineer-in charge. |
| 104 | Material and labour for replacement of unserviceable sealed unit (compressor) with new sealed unit (compressor) for deep freezer capacity 400/500 litres, including vacuuming the system, supply and charging Gas at rated pressure, detection of leakage etc., brazing and testing to achieve proper cooling effect complete all as specified and directed. |
| 105 | Material and labour for replacement of unserviceable sealed unit (compressor) with new sealed unit (compressor) for deep freezer capacity 300 litres including vacuuming the system, supply and charging Gas at rated pressure, detection of leakage etc., brazing and testing to achieve proper cooling effect complete all as specified and directed. |
| 106 | Material & Labourforleakdetection by nitrogen pressure test in refrigerant system of deep freezer of any make/type/ capacity, by cutting, brazing and making leak-proofthe gas system, cleaning, vacuum the gas system and charging suitable gas of any type as required quantity to achieve desire coolingincluding installation at site, testing of water cooler on full load for 24 hours continuously complete all as specified an directed. (Note:- Supply and charging additional gas required willmeasured & paid separately under relevant item) |
| 107 | Supply and fixing in replacement of thermostat suitable for deep freezer 300/400/500 ltrs capacity all as specified directed by Engineer-in-Charge . |
| 108 | Supply and fix in replacement starting relay of deep freezer of different make and capacity 300/400/500 ltrs complete all as specified and directed. |
| 109 | S&F in replacement offan motor for deep freezer 300/400/500 ltrs capacity complete as per existing make all as specified and directed . |
| 110 | Taking up or down steel water tubing of size 15/20mm bore from trenches or walls etc. complete all as directed. |
| 111 | Supply & laying galvanized steel water tubing, medium grade of 15 mm bore, screwed and socketed joints with and including all required fittings and fixed complete to wall and ceiling or laid in floor old and new location etc complete all as directed. |
| 112 | All as per Srl item No 111 but pipe of size 20mm bore |
| 113 | Supply and fixing in replacement of copper tubing of suitable size 1/2\" and 3/4\" for suction and discharge line two run for split type AC with insultionto protect the heat etc complete all as specified and directed. |
| 114 | Supply & fixing toughened fibre body with glass wool/ foam insulation including top cover suitable for 300 lt capacity deep freezer body includingcopper cooling coil of specified dia and length for smooth cooling complete all as specified and directed. |
| 115 | All as per SI item no 114 but for capacity 400 ltr Deep freezer. |
| 116 | All as per SI item no 114 but for capacity 500 ltr Deep freezer. |
| 117 | Supply and fixing of condensing coil for 300 ltr capacity deep freezer all as specified and directed. |
| 118 | All as per SI item no 117but for capacity 400 ltr deep freezer. |
| 119 | All as per SI item no 117but for capacity 500 ltr deep freezer . |
| 120 | Package type AC Plant:M & Lfor replacement of scroll type new compressor of capacity 7.5 Ton for package AC Plant suitable for air conditioner of any make/as per existing type including replacement of foundation bolts, rubber pad, strainer capillary tubes, suction and discharge pipe line, wiring kit, supply and charging Gas (R-22/R-134A) and detection of leakage etc., brazingand testing to achieve proper cooling effect complete all as specified and directed by Engineer-in-charge. |
| 121 | Supply and fixing power contactor AC3 rating 25 amp 3 pole all as specified and directed. |
| 122 | M & L for rewinding for electric motor 2 HP with exiting size/guage super enanmelled copper winding wire, insultaing material, replacement of bushes, varnising drying complete including taking out and refixing and testing in position complete all as specified and directed |
| 123 | M & L for Servicing of Package type AC Plant 17 Ton capacity by cleaning all the coarse type filter, tightening of loose contacts of wires, connectors, relays, compressor terminal and checking for smooth functioning. The servicing include leakdetection by nitrogen pressure test in refrigerant system, cutting brazing and making leak-proofthe gas system, cleaning, vacuum thegas system and charging suitable gas of any type as required quantity to achieve desire cooling and changing of wiring with proper size PVC insulated wires, relays and MCBs as required for smooth functioning of AC plant including painting of all exposed parts with synthetic enamel paint of one paint including testing of the AC plant all as specified and directed by the Engineer in charge . Notes: 1. The Job shall be completed within one month after date of commencement of work due to urgency in nature failing which a Penalty of Rs 1000.00 per day after one month of period will be lavied on contractor, if the Job not completed. 2. Additional gas required will measured & paid separately under relevant item as supply and charging. |
| 124 | Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender.The Schedule of Credit is pre-priced by MES.The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit. |
