Repair And Replacement Of Plastering, Flooring, Joinery, Connected B / R Items And Periodical Services To Otm Accn In New Cantt Zone ‘A’ At Mil Stn Patiala Under Ge ( South ) Patiala. 1 Taking down chowkhats or frames (Wooden joineries with wooden or steel chowkats) complete with shutters (without taking off shutters from the frames) exc 1.5 sqm butnot exc 4.00 sqm each and removing from site or to store as complete all as specified and directed by Engineer-in-charge. 2 Taking down chowkhats or frames(Wooden joineries with wooden or steel chowkats) complete with shutters (without taking off shutters from the frames) notexc 1.5 sqm each and removing from site or to storecomplete all as specified and directed by Engineer-in-charge. 3 Taking down wooden shutters of any description exc 1.00 sqm but not exc 2.00 Sqm each and removing from site or to storecomplete all as specified and directed by Engineer-in-charge. 4 S &F Pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc,complete all as specified and directed by Engineer-in-charge. 5 Description all as per serial item No 4 here-in-before but size 105 x 60mmcomplete all as specified and directed by Engineer-in-charge. 6 M&L For Cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in mass concrete or filling backs of chowkats complete all as specified andcomplete all as specified and directed by Engineer-in-charge. 7 S&F Factory made flush shutters 35mm thick minimum 5 ply, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick lipping frame to match including supply and fixing following itemscomplete all as specified and directed by Engineer-in-charge:(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm -4 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 150mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 Nos per leaf(d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm- 1 No per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper- 1 No per leaf 8 S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (wire dia. 0.36mm) and supply and fixing the following itemscomplete all as specified and directed by Engineer-in-charge.:(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm -3 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 150mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 Nos per leaf(d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm- 1 No per leaf 9 Providing and fixing factory made extruded aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled anddouble shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed incomplete all as specified and directed by Engineer-in-charge including supply and fixing following items :-(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm -2 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf.(c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf. 10 S & F Anodised aluminium window and ventilator shutters fixed type without sash bar,powder coating of any colour ( thickness of powder not less than 50 microns). Aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc.complete all as specified and directed by Engineer-in-charge. 11 Powder coated 50 microns extruded aluminium glazing doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below & above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. and aluminium beads 20mm sizecomplete all as specified and directed by Engineer-in-charge.including supply and fixing the following items:(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm -3 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf(c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf 12 S & F in repair Aluminium tower bolt 200mm longAddand fixedcomplete all as specified and directed by Engineer-in-charge. 13 S & F in repair Aluminium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer-in-charge. 14 S & F in repair Mild steel butt hinges of size 100mm medium weight cold rolledcomplete all as specified and directed by Engineer-in-charge. 15 S & F in Repair Floor door stopper 150 mm long of aluminium alloy body and toungue anodised with hard drawn steel springfixedin floorscomplete all as specified and directed by Engineer-in-charge. 16 S & F in repairAluminium handles of size 150mm ovaltypecasttype anodisedcomplete all as specified and directed by Engineer-in-charge. 17 Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conformint to Fe-410 W complete all as specified and directed by Engineer-in-charge. 18 S & F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing S& F complete all as specified and directed by Engineer-in-charge. 19 S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-charge. 20 S & F 100 mm size PVC butt hingescomplete all as specified and directed by Engineer-in-charge. 21 S & F 125 mm PVC handlescomplete all as specified and directed by Engineer-in-charge. 22 S & F200 mm long PVC tower boltcomplete all as specified and directed by Engineer-in-charge. 23 M & L For Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and directed by Engineer-in-charge. 24 M & L for Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paintcomplete all as specified and directed by Engineer-in-charge. 25 Factory made steel window box type using ERW hollow P section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8mm square bars, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3complete all as specified and directed by Engineer-in-charge and as approved by GENote: (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill as shown on drgs.(iii) Glazing, wire mesh & painting shall be measured & paid for separately. 26 Taking down old unserviceable wire cloth any size from wooden/ metal framescomplete all as specified and directed by Engineer-in-charge. 27 S & F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples incl replacement of second class wooden beading where ever reqdcomplete all as specified and directed by Engineer-in-charge. 28 Hacking out old broken glass (any thickness , size , quality or description) from wooden or metal frames glazed with oil putty or fixed with beads complete all as specified and directed by Engineer-in-charge. 29 S & F Sheet glass ordinary quality 4 mm thick not exe.0.50 sqm glazing with oil putty or fixed with wooden beads in squares any size of panecomplete all as specified and directed by Engineer-in-charge. 30 Description all as per serial item No 38 here-in-before but 4mm thick frosted glasscomplete all as specified and directed by Engineer-in-charge. 31 S&F Mild steel rat tail rod pattern helical door spring of size 300mm including roller and roller plate fixing to iron frame by weldingcomplete all as specified and directed by Engineer-in-charge. 32 Demolition of cement concrete un-reinforced in ground floors and pavingsnexec 150 cm thick (above or below ground level) complete all as specified and directed by Engineer-in-charge. 33 Demolition of re-inforced cement concrete of any description and in any position incl cutting of re-inforcement to facilitate demolition where everreqd complete all as specified and directed by Engineer-in-charge. 34 M & L for Machine cut Mirror polished Kota stone 20mm-25mm thick slab as in cooking platforms/ landings, treads and risers of stairs and stepslaid over and includingscreed bed or 15mm th bedding layer in cement mortar 1:3 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishingcomplete all as specified and directed by Engineer-in-charge. 35 M & L for Machine cut Mirror polished Kota stone slab flooring 20mm-25mmthick laid over and including 20mmscreed bedor bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishingcomplete all as specified and directed by Engineer-in-charge. 36 Rounding to edges of stone slabs one edge , such as in steps, cooking plateforms & other similar situationscomplete all as specified and directed by Engineer-in-charge. 37 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-charge. 38 M & L for Glazed ceramic coloured tiles in verticle surfaces joint free with glazed economy finish Grade B-II (b) of size 300 x 600mm or bigger size7 mm thickas approved set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10 mm thick rendering in cement mortar in CM 1:3 for Dado etc.,complete all as specified and directed by Engineer-in-charge.Note for skirting onlySkirtingmay be providedfrom the same tiles as being used in the floor of sameroomto match in lieu of economy finish tiles but nothing extra shall be admissible on this account. 39 M & L for Non Skid Ceramic joint free tiles {Non Skidfinish/ Matt superior finish Grade B-I or B-II (b) as approved}7 to 8 mm thick with rectified edges, (square/rectangular) area of each tile exceeding 0.11sqm and not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15 mm thick cement screedbed in CM 1:4complete all as specified and directed by Engr-in-Charge 40 M & L for Vitrified Ceramic tiles 8-9mm thick light colour (Square/ rectangular) polished, area of each tile 600 x 600 mm , in floors etc. set and jointedin neat cement slurry and pointed in white or coloured cement to match the shade of tileover 15mm thick screed/ bedding layerin CM 1:4complete all as specified and directed by Engineer-in-charge. 41 M & L for PCC 1:2:4 type B1 (using 12.5mm graded stone aggregate)25 mm thick to receive the floortiles complete all as specified and directed by Engineer-in-charge. 42 Taking down cementplaster or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed by Engineer-in-charge. 43 M & L for rendering 15mm thick cement plaster in cement mortar 1:4 using WPCon fair faces of brick or concrete surfaces on walls etc., finishedeven and fairwithout using extra cement, complete all as specified and directed.Note: - Supply only WPC Shall be measured separately & paid for accordingly & shall beprovided @ 3% by weight of cement or as per manufacturers instructionscomplete all as specified and directed by Engineer-in-charge. 44 Supply only Liquid waterproofing compound complete all as specified and directed by Engineer-in-charge. 45 M & L for rendering 10 mm thick cement plaster in cement mortar 1:6 on fair faces of brick or concrete surfaces on walls etc., finishedeven and smooth without using extra cement,complete all as specified and directed by Engineer-in-charge. 46 Dubbing out average 15 mm thick in cement mortar 1:4 on irregular faces of walls, ceiling & chhajjas incl removing carefully old damaged loose concrete from RCC / PCC surfaces of ceiling/ Chhajjas for double storey bldgscomplete all as specified and directed by Engineer-in-charge. 47 M & L for Rendering 10mm thick cement plasterin CM 1:3on concrete surfaces in ceiling/ Chhajjas finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. 48 Preparation of new plastered or unplastered surfaces of walls etc.,and M & L for applying twocoat of distemper Oil Emulsion (OBD) over a coat of chalk whiting (as primer)complete all as specified and directed by Engineer-in-charge. 49 M & L for Preparation of new plastered or unplastered surfaces of ceiling etc.,and applying three coat of lime white wash on ceiling surfacescomplete all as specified and directed by Engineer-in-charge. 50 Preparation of new plastered or unplastered surfaces of walls etc.,and M & L for applying twocoat of cement base paintover a coat of Alkli Resistance priming paint (as primer)complete all as specified and directed by Engineer-in-charge. 51 M & L for PCC 1:2:4 type B1 (using 12.5mm graded stone aggregate) as in roof kerbs, PCC Khurras, coping on parapet wall, mud stops, steps small sumps and like items slightly rounded or chamfered on the edgescomplete all as specified and directed by Engineer-in-charge. 52 Racking out joints , hacking for key incl removal of all grass, vegetation growth from roofs etc., andM & L for flush pointing to roof tiles/ terracing incement mortar 1:3complete all as specified and directed by Engineer-in-charge. 53 Demolition of Brick work including all quains and arches pillars etc built in cement mortar or cement lime mortarcomplete all as specified and directed by Engineer-in-charge. 54 M&L for brick work in cement mortar (1:6) using sub class B old size bricks staight or curved on plan exc 6.0 m mean raiduscomplete all as specified and directed by Engineer-in-charge. 55 M & L 50mm thick PCC (1:3:6) type C2 (using 40mm grade aggregate) as in plinth protection, finishing the surfaces even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-charge. 56 S & F precast concrete interlocking paver block any shape and size & incl 25mm thick layer of sand cushion complete all as specified and as directed. confirming to IS 15658-2006 of 60 mm thickness, M-35 gradecomplete all as specified and directed by Engineer-in-charge. 57 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-charge. 58 Dismantling timber scantlings in framed work 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer-in-charge. 59 Anodised aluminium snap grid frame work for false ceiling all as specified (Size of grid 605 x 605mm) incl Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm longcomplete all as specified and directed by Engineer-in-charge. 60 Material & labourforGypsum Board 600mmx 600mm x 12mm thick in ceiling fixedas per manufacturers instructions all as specified andcomplete all as specified and directed by Engineer-in-charge. 61 S & F for hollowPVC Wall Liningconsisting of5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engineer-in-charge. 62 M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-charge. 63 S &F in repairPVC (SWR) pipe110 mm bore Rain water pipe single socketed in any length with rubber ring joints,fixed to wall complete all as specified and directed by Engineer-in-charge. 64 Complete removal of existing treatment of any type/description such as cement base paint, external emulsion etc from external surfaces of walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc with mechanical means/grindercomplete all as specified and directed by Engineer-in-charge. 65 Applying acrylic wall care putty in external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving exterior paintingcomplete all as specified and directed by Engineer-in-charge.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. 66 Applying 02 coats of exterior emulsion paint (light shade) as per manufacture instructions by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed by Engineer-in-charge. 67 Writing letter of figures (block, roman italic or Indian) n exc 30cm high complete all and the colour of paint and dimension of letter to be used as approved by Engr-In-Charge. 68 Writing stops , commas, short lines, dashes, hypens, brackets etc and the colour of paint and dimension of letter to be used as approved by Engr-In-Charge. 69 M&L for cement plastering 5mm thick in(Small Patches) cemet mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. 70 Complete removal of existing treatment of any type/description such as distempering work, internal emulsion etc from internal surfaces of walls & ceiling with mechanical means/grindercomplete all as specified and directed by Engineer-in-charge. 71 Applying acrylic thick wall care putty on internal surfaces of walls/ceilings (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior paintingcomplete all as specified and directed by Engineer-in-charge.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. 72 Applying 02 coats of interior emulsion paint (light shade) as per manufacture instruction by using roller to wall surfaces over & including a coat of interior wall primer as recommanded for under coat by manufacturer of interior emulsion by using following brands of emulsion and primercomplete all as specified and directed by Engineer-in-charge. 73 M&L For preparing existing old treated surface of external Walls/RCC Surfaces/Soffits of Chajjas/Roof Projection/Centilevers/Balcony etc Incl Cornices and applying one coat of Cement base paint @5Sqm/KG/1 Coat by usingof cement based paint by rollercomplete all as specified and directed by Engineer-in-charge. 74 M&L For preparing existing old treated surface of external Walls/RCC Surfaces/Soffits of Chajjas/Roof Projection/Centilevers/Balcony etc Incl Cornices and applying Two coat of Cement base paint @5Sqm/KG/1 Coat by usingof cement based paint by rollercomplete all as specified and directed by Engineer-in-charge. 75 M& L for prepration of old plastered surface/unplastered Surfaces including washing, rubbing down and stoping of Distempered and painted surfaces and applying Two coat of Oil Bund Distemper on wallcomplete all as specified and directed by Engineer-in-charge. 76 M& L for prepration of old plastered surface/unplastered Surfaces including washing, rubbing down and stoping of Distempered and painted surfaces and applying one coat of Oil Bound Distemper on Wallcomplete all as specified and directed by Engineer-in-charge. 77 M & L for preparing existing treated surfaces on Wall including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. 78 M & L for preparing existing treated surfaces on Wall including cornices and applying Two coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. 79 M & L for preparing existing treated surfaces on ceiling including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. 80 M & L for preparing existing treated surfaces on ceiling including cornices and applying Two coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge. 81 M & L for preparing old painted steel and iron surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge. 82 M & L for preparing old painted wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.
