E-Tender On Turn Basis For Providing Power Supply In Kauriaganj, Extended Nagar Panchayat Under The Area Of Shashwam, Aligarh, According To The Prescribed Roster, According To The Desired Work.- 1 St Pole 11 Mtr. Long 2 Stone Pad ( 300X300x75 Mm ) 3 Top Channel ( 125X65x2240mm ) 4 Dropper Channel ( 100X50x2028mm ) 5 V-Type Steel Cross Arm With Clamp 6 11 Kv Pin Insulator With Pin Complete 7 11 Kv Disc Insulator With Fitting 8 M.S. Angle ( 75X75x6x2028mm ) ( T / F Base ) 9 M.S. T-Off Channel With Clamp B&N ( 100X50x1300mm ) 10 F-Bracket For Fitting Top Channel 11 Holding Clamp For Tpmo & Fuse Set With Bolt Nut 12 Number Plate With Clamp N&B 13 Danger Board With Clamp N&B 14 Stay Set Complete With Grouting 15 Earthing Rod Complete 16 Distribution Box With Clamp 17 Abc 3X95 + 1X70 + 1X16 Sq.Mm. 18 Abc 3X120 + 1X95 + 1X16 Sq.Mm. 19 P.G. Clamp 20 End Clamp 21 Insulator Suspension Clamp With I Hook 22 Dead & Clamp With I Hook 23 Lt Insulator Pearsing Connector 24 Bolt, Nut & Washers 25 11 / 0.4 Kv 250 Kva Transformer 26 11 / 0.4 Kv 63 Kva Transformer 27 33 Kv Vcb 800, 800 A 750 Mva 28 Cable Al. 3X300 Sq.Mm. Xlpe Cable 11 Kv 29 11 Kv Xlpecable Size 3.5*X70 Sq.Mm. 30 Ltcable Size 3.5*X70 Sq.Mm. 31 Pvc Cable 3.5*X 240 Sq.Mm. 32 11 Kv Xlpe Cable O / D Cable Jointing Kit For 3X300sq.Mm. 33 11 Kv Xlpe Cable I / D Cable Jointing Kit For 3X300sq.Mm. 34 11 Kv Xlpe Cable O / D Cable Jointing Kit For 3X70sq.Mm. 35 Barbed Wire G.I. 36 33 Kv Fuse Set 37 Phase Wire Acsr Weasel Conductor 38 Red Oxide Paint 39 Aluminium Paint 40 Aluminium Tape 41 Carriage & Installation Of 10 Mva 33 / 11 Kv Power Transformer With Accessoriesas Per Direction Of Supervising Engineer Including The Cost Of Arrangement Of All Material, Labourer, T&P, Carrier Etc. Required For Proper Completion Of Work. 42 Body And Neutral Earthing Of Followingtransformers Installed By Digging Of Pit Up To Water Level Depth ( Approx. 100’ ) And Then Inserting1-1 / 4 Dia G.I. Pipe Of B Grade, Conforming To The Requirement Of Is Specification And Then Connecting The Top Of The Inserted Pipe And Transformer Body Through Gi Strip Of Size 50X6 Mm With The Help Of Nut And Bolt Or Through Gas Welding, As Per Direction Of Supervising Engineer Including The Cost Of Arrangement Of All Material, Labourer, T&P, Carrier Etc. Required For Proper Completion Of Work. 43 10 Mva Power Transformer 44 11 / 0.4 Kv 250 Kva Transformer 45 Complete Chemical Earthing Of 33 Kv Vcb By Digging Pits 6” Dia Upto 3 Mtr. Deep Including Chemical Filled Pipe In Between ( Pipe-In-Pipe ) Isi Mark B Grade & Connecting With G.I Strip Of Size 50Mm X 6Mm With Neutral / Body Of 11 / 0.4 Kv Distribution Transformer To Above Pipe-In-Pipe ( Pip ) And Filling Of Chemical Crystalline Conductive Mixture Containing Highly Conductive Material Around The ( Pipe-In-Pipe ) Up To 3 Mtr. Including Making Of Chamber At The Top Of The Earthing. Other Details Are As Below:-1. Earth Pipe Material – Mild Steel, Galvanized.2-Main Electrode Diameter – 42.4Mm.3-Auxiliary Electrode Pipe, Diameter – 76Mm. 4-Wall Thickness Of Main Electrode: - 2.6Mm.5-Wall Thickness Of Auxiliary Hole: - 3.2Mm.6- Length Of Earthing Electrode ( Pip ) :- 3 Meter. 46 Construction Of Following Transformer Of Plinth Of Size 5’X5x4’ Above Ground Level And One Ft. Below The Ground Level Of 9”. After Excavation Of 4” Earth, Brick Ballast Shall Be Provided And Rammering Will Be Done Properly After That A Retaining Wall Of 9” Width By First Class Brick In Ratio 1:4 Of Cement And Sand Shall Be Made. The Earth Shall Be Filled Up To One Ft. Below The Top Of The Plinth. After This Brick Ballast Shall Be Provided Up To 6” From The Earth Level And Proper Rammering Shall Be Done. One No. Jall Of 12 Mm M.S. Tor Shall Be Fixed In The Hollow Of Plinth And One Ft. Thick Rcc In Ratio Of Cement, Sand And Stone Ballast Shall Be Laid On The Top Of The Plinth. The 12 Mm Thick Plastering Shall Be Done All Around The Plinth In 1:4 Ratio Of Cement And Sand. The Contractor Shall Be Responsible To Complete The Work As Per Direction Of Supervising Engineer. It Including The Cost Of All Material, Labour T&P, Carrier Etc. Required For Proper Completion Of Work. 47 11 / 0.4 Kv 250 Kva Transformer 48 10 Mva Power Transformer Plinth Of Size 3.46X4.46 Mtr. Having 0.5 Mtr. Below Ground Level And 0.4 Mtr. Above Ground Level. 49 Fabrication & Erection Of Fencing And Construction Of Retaining Wall Aroundfollowing Capacity T / Fthe Complete 11 / 0.4 Kv Substation Shall Be Provided With Two Meter Height Fencing And Retaining Wall Around The Substation. One No. Gate With Proper Locking Arrangement For Entry Of Personnel Shall Also Be Provided. The Fencing Shall Be Made Of 50X25 Mm X10 Swg Rectangular Welded Mesh Of Wire Mesh In Length. Wire Mesh Shall Be Fixed On Panels Made Of 50X50x6 Mm M.S. Angle. The Wire Mesh On Panels Will Be Supported By 25X3 Mm M.S. Flat On All The Bracings Diagonally And 50X6 M.S. Flat Horizontally At The Center Of The Panel. The Panel Will Be Joined By Bolts & Nuts Of Appropriate Size With Each Other And On The Main Support On Corners Including Supply Of All Material, Labour, Carrier And T & P Etc. Required For Proper Completion Of Work. The Painting Of Complete Fencing Shall Also Be Done With One Coat Of Red Oxide Primer And Two Coat Of Synthetic Green Paint. For Construction Of Retaining Wall Around The Fencing, Excavation Of Earth Shall Be Done In Foundation In Ordinary Soil Including Disposal Of Surplus Earth At Some Suitable Distance. The Dimension Of Excavation Shall Be 1M Wide, 0.45 M Deep And Suitable Length As Per Wire Mesh. After Excavation Of Earth A Cement Concreted Pad Shall Be Laid In Foundation. Concreting Shall Be Done With Ist Class Brick Ballast, Coarse Sand And Cement In Proportion Of 8:4:1. First Class Brickwork Shall Also Be Done In Foundation And Super Structure In 1:6 Cement And Coarse Sand Including Necessary Cutting And Moulding Of Bricks In Foundation Depth Of Wall 0.30 M, Thickness Of Wall 0.35 M & Superstructure Brick Work Thickness Of Wall 0.23 M & Depths 0.30 M Including Supply Of All Material, Labour, Carrier And T & P Etc. Required For Proper Completion Of Work. 50 11 / 0.4 Kv 250 Kva Transformer 51 Demounting & Carriage Of Following Capacity Transformer Due To Overloaded Including The Work Of Its Loading & Unloading, Dragging Etc. And Also Including The Cost Of Labour And T&P Etc. Required For Proper Completion Of Work. 52 11 / 0.4 Kv 100 Kva Transformer 53 11 / 0.4 Kv 63 Kva Transformer 54 Dismantling And Removal Of Existing Conductor / Cable / Gi Wire From The Various Area Preparing Their Coils And Then Stacking In The Respective Je’S ( Store ) As Per Direction Of Supervising Engineer. It Includes The Work Of Cartage, Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work. 55 Acsr Weasel Conductor 56 Concreating Of Pole 57 Guarding Of 11 Kv Line By Laying Two Nos. Gi Wire Parallel And Fixing Of Lacings ( Tilli ) At A Distance At 2-3 Mtr. As Per Respo Manual And Also Including The Cost Of Arragement Of Labour, T & P Etc. Required For Proper Completion Of Work. 58 Safe Carriage Of Old Line Material Viz. Conductor, G.I. Earth Wire, Abc Conductor, Cross Arm, Angle, Channel, Insulators, Clamps & Other Line Material From Any Other Place Or From Site Of Work To The Work Of Its Loading & Unloading At The Respective Ends Including The Cost Of Labour, T&P And Carrier Etc. Required For Proper Completion Of Work. 59 Dismanteling Of Old Damaged 33 Kv Vcbs ( 800 A 750 Mva ) After Opening Its 11 Kv Cable Connection Removing Earthing Bus Bar Cts And Taking It Out Side Switch Yard.The Work Of Cartage, Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work.
