Provision Of Borewell In Tech Area And Upgradation Of Stores At Various Location At North Camp Under Ge ( Af ) Bamrauli -Trial Bore Well Of 200 Mm Dia Size Pilot Bore Through Any Soil Strata Including Hard Stone / Boulder By Means Of Directrotary Method Below Ground Level Complete All As Specified & Directed By Engineer-In-Charge. Note: Unit Rate Quoted By Tender Shall Be Deemed To Include Cost Of Ms Pipe And Transportation Of Rig Accessories Required, Developing And Testing Etc At Site Of Work And Removal Of The Same On Completion From The Site Including Necessary Supervision And Rent Charges Of Rig Machine Compressor & Op Unit ( Any Other T&P Not Specifically Mentioned ) In Respective Item Of Sch AAnd No Extra Payment Shall Be Admissible On This Account. 2 Drilling Reaming Vertical Bore 525 Mm Dia At Approved Site / Location In Any Type Of Strata For 250Erw Casing Pipe For Various Depth As Shown Below Including All Works Pertaining To Boring Complete In All Respect And All As Specified & Directed. 3 ( A ) Reaming Up To 525 Mm Dia For 60 Mtr Depth From Ground Level For Casing Pipe 250 Mm Dia. 4 ( B ) Reaming Up To 525 Mm Dia For Exceeding 60 Mtr To 150 Mtr For Casing Pipe Of 200 Mm Dia. 5 Supply And Assembly Including Jointing, Lowerings And Fixing In Position Erw Plain Steel Pipe ( Seamless ) Housing Pipe 250 Mm Bore ( Nominal Dia ) 8.00Mm Thick And Outer Dia Of Pipe 266 Mm Conforming To Is-8110-2000 Class 8.1.1 Plain End Pipe Jointed And Welded Couper Ring ( Welding Shall Be Done Through Out The Circumference Of The Pipe And Coupler Ring Both Sides All As Specified And Directed By Eic. Make : Jindal / Tata. Note :- ( A ) Length Of Pipe Shall Not Less Than 2.40 Mtr Except Where The Pipe Length Required Is Less Than 2.40M ( B ) Effective Length Shall Only Be Measured And Paid. 6 All As Per Item No 3 Above But Supply Assembling, Jointing Plain Ms Pipe ( Seamless ) Casing 200 Mm Bore 8 Mm Thick And Outer Dia Of Pipe 216 Mm Conforming To Is 8110-2000 Complete And Lowering And Fixing Position After Socket Reducer Of 250X200mm Bore. 7 S&F Ms Strainer ( Slotted ) Pipe V Weired 200 Mm Bore, 8 Mm Thick Conforming To Is 8110-2000 Fabricated With Pipe Or Specification Mentioned Above ( Item No 3 ) Slot Of Size 1.55Mmx75mm As Per Is Provn Uniformly Distributed On The Surface All As Specified. 8 S&F Mild Steel Reducing Socket 250Mmx200mm Dia Of Suitable Length Including Welding, Mild Steel Strip 40X6mm 2 Nos On Each Joint Extended In 75Mm On Each Side All As Specified. ( The Wall Thickness Of Socket Not Less Than 8 Mm Thick. 9 S&F Wrought Iron Bail Plug 200 Mm Bore, All As Specified. 10 S&F Well Cap For 266 Mm Dia Housing Pipe All As Specified And Directed. 11 S&F Two Nos Ms Flat Iron 150 Mm X 15 Mm Housing Clamp For Holding To 250 Mm Dia Housing Pipe With 16Mm Ms Bolt & Washers Including Casting Of Pcc Blocks 1:2:4 Type B-1 Using 20Mm Graded Stone Aggregate Of Size 1.20 M X 1.00 M Including 50Mm Dia Ms Pipe 2 Nos Each 1.5Mtr Long With Cap Plug And Cap Top For Filling Pea Gravel Including Necessary Excavation & Each Work In Any Type Of Soil Complete All As Specified And Directed. 12 M&L For Packing Pea Gravel Of Size 3 To 5Mm Natural Shape Brought Direct From River Bank And Packing Around Casing Pipe To Entire Depth Up To Ground Level All As Specified Anddirected. ( Length Of Assembly Packed Only Be Measured For Payment ) 13 Development Of Tube Well By Means Ofhigh Velocity Compressored Airwith 350 Psi Air Compressor All As Specified In Is-11189-1985 Para 4.2Including Arrangment For Equipment Fitting. 14 Supply Of Sodium Meta Hexa Phosphate For Disinfecation Of Bore Well All As Specified And Directed. 15 Development Of Tubewell Bymeans Of Over Pumping For Subsequent Hours Until Clear Discharge As Per Clause 9.3.2 Of Is 2800 ( Part-1 ) -1991All As Specified And Directed. 16 Supply Only Strata Sample Box With Glass Cover 3Mm Thick And Having Internal Dimension 1.0 Mtr X 0.60 Mtr X 0.10 Mtr Made Out Of Shisham Plank 20Mm Thick With Hinges, Hasp And Staples Including Polishing Complete With Samples At Various Depth Met At The Time Of Boring Including Stata Chart In Duplicate. 17 Chemical Bilogical And Potability Testing Of Water Sample Taken From The Bore At Govt Approvedlaboratories. Note:- Test Certificate Obtained From Approved Lab Will Be Submitted By The Contractor In Original. 18 Yield Testing For Bore Well By Continuous Pumping For 16 Hrs To Determine Safe Pumping Yield Of The Tube Well As Perclause 5 Of Is 2800 ( Part-Ii ) -1979 Complete All As Specified And Directed. 19 Electric Logging In Trial Bore Precise Delineation Of Granular Zones And Also The Quality Of Ground Water Including Report Interpreatation Complete All As Specified And Directed. Note:- Electric Logging Shall Be Carried Out By Approved Agency. 20 S&F Air Release Valve Suitable To Connect Column Pipe Of Rising Main Flanged And Column Pipe Or Submersible Pump Set Compelte With Nut, Bolt Washer Etc Including Grouting 4 Bolt On Pcc Plateform All Specified 21 Supply, Lowering, Jointing And Testing Ms Black Column Pipe 3 Mtr Long Heavy Duty 100 Mm Bore Wall Thickness 5 Mm Both Ends Flanged With Heavy Duty Ms Flanged Not Less Than 16 Mm Screwed And Welded In Side And Outside. The Flanged End Making Surface Shall Be Smooth Including Welding Of 04 Strip Of 5 Mm Thick 25 Mm Wide And 50 Mm Long Covering Pipe And Flanged, Both End Flanged Having 08 Nos Predrilled Hole Not Less Than 16 Mm Including Rubber Gasket, Nut Bolts And Washer, Pipe Should Be Duly Painted With Anti Corrosive Paint Complete All As Specified And Directed. 22 Supply, Fixing, Jointing And Testing Of Cast Iron Non Return Valve 100 Mm Dia Flanged Ends As Per Is-5312 ( Isi Marked ) Complete With Washer Nuts / Bolts And Rubber Gasket Complete All As Specified And Directed. 23 Supply, Fixing, Jointing And Testingof Cast Iron Sluice Valve 100 Mm Class I ( Isi Marked ) Pn-1 Typelatest Is 14846-2000 Flanged Ends, Drilled Having Stainless Steelspindle With Cast Iron Wheel Head At Top Complete With Nuts, Bolts, Washer And Rubber Gasket Etccompleteall As Specified And Directed. 24 Supply, Installation, Commissioning And Testing Submersible Pumping Setmulti Stage Electric Driven Of 10 Hp Capacityat Operating Head Range 10-40 Mtr Head, Directly Coupled With Electric Motor, Ac 3 Phase, 415 Volts, 50 Hz, 2900 Rpm With Copper Wound Water Proof Winding Complete With Flange Adoptor Suitable For Connection With 100 Mm Dia Flanged Column Pipe And One Set Of Essential Tool With Price List, Literature As Recommended By Manufacture Complete Complete All As Directed. 25 S&F Submersible Pump Controller In Sheet Enclosure Type Mu-G20 Fully Autimaticstar Delta Starterfor Threephase Motor 415 Volts, 50 Hz, 3 Phase, 15 Hp, 9-14 Amps Relay Range All As Specifiedmake : L&T Cat Part No. :Ss95984coaoor Equivalent 26 S&F In Replacement Of Pvc Insulated Flat Copper Submersible Cable Heavy Duty 16 Sqmm 3 Core 1100 Volt Grade Of The Following Size Complete All As Specified And Directed. Make - Havells / Plaza / Finolex 27 Supply And Fix High Pressure Single Head Adjustable Chlorine Dosing System Including Frp Pressure Dosing Tank Of Capacity 100 Ltrs Consisting Of Water Inlet Line, Outlet With Y Strainer, Drian, Overflow, Conical Bottom For Sludge Deposition , Pot Hole With Cover, Level Gauage With Agitation Motor 120 Watts 960 Rpm, Single Phase Flange Mounted Motor With Plastic Shaft And Impeller Connected To Frp Service Dosing Tank Of Capaicty 100 Lts Consisting Of Water Inlet Line, Dozing Injector 230V, 50Hz Including On / Off Switch And Stokes / Minute Of Max 135 Min. 15 With Motor, Discharge Pressure 10Kg / Sqcm, High Flow Rate Of 0-25 Lph Including Drain, Overflow Level Gauge, Inspection Port, Agitator Motor 120 Watts 960 Rpm Single Phase Flange Mounted With Plastich Shaft And Impeller Including Mounting Lid, Complete All As Directed. Make: Aquafit Or Equivalant 28 Supply & Laying In Trenches Ductile Iron ( Di ) Pipe Of Size 100 Mm Bore Dia With Spigot And Socketed Ends Centrifugally Cast Class K-7 In Any Length Laid In Trenches Including Di Fittings And Jointing Materails Complete All As Specified And Directed. 29 M&L For 100 Mm Bore Cast Iron ( Di ) Fittings Such As Bends ( Any Type, Radius And Angle ) Tapers Any Type, ( Straight, Bend, Increasing, Decreasing Or Double Socket Etc ) Tee Pieces Single Branch, “Y” Junction, Double Branch, Cross ( All Sockets Or Socket And Spigot ) Collars, Caps And Plugs Complete All As Specified And Directed. 30 Supply And Lay Steel Water Tubing Gi Medium Grade Isi Marked With All Fittings Laid In Trenches Or Fixed To Wall Etc Complete For The Following Sizes:-Make: Jindal / Prakash / Swastik Note :- Excavation And Earth Work Will Be Measured And Paid Separately. 31 ( A ) 40 Mm Dia Bore 32 ( B ) 25 Mm Dia Bore 33 S&F Gun Metal Gate Valve Isi Marked With Iron Wheel Head Screwed Both Ends For Iron Pipes And Fixed For The Following Sizes Including Taking Down Of Unserviceable Gate Valves. Make : Zoloto / Seico / Jindal / Upadhaya / Venus 34 ( A ) 40 Mm Bore 35 ( B ) 25 Mm Bore 36 Supply, Install, Testing And Commissioning Of Busbar Chamber Of Size Not Less Than 60Cm X 60Cm X 25Cm For 3 Phase, 415 Volts Ac, Outdoor Type, Cubical Compartmentalised Type, Weather, Vermin And Water Proof, Fabricated Out Of 2 Mm Thick Crca Sheet Powder Coated Front Door Openable With Locking Arrangemen And Iron Angleframe Bottom Of The Panel Board Including 100 Amps Mccb , Rated Copper Bus Bar, Phase Indicator , 15 Amps Switch Socket Combined , Grouted Using Pcc Foundation 1:2:4 Type C1 With 20 Mm Graded Stone Aggregate, Thimbling And Cable Entry Boxes With Cable Gland Including Painting With Two Coat Of Powder Coated Painted Over A Coat Of Red Oxide Primer Complele All As Specifed And Directed. 37 M&L For Earthing Complete With Galvanized Steel Earth Plate 600X600x6mm Thick Buried Directly In Ground ( Earth ) Pit Not Less Than 2.25 Mtr Deep Below Ground Level ) With Top Edge Of The Plate Not Less Than 1.5 Meters Below Normal Ground Level Connected To Galvanised Iron Strip 25X4mm As Earthing Lead By Means Of Bolts, Nuts, Check-Nuts And Washers Of Galvanised Iron Or Steel Besides Welding At All Joints As Shown In Drawings And Including Excavation And Earth Work, Gi Pipe Light Grade 40Mm Bore For Protection Of Gi Strip From Earth Electrode To And Including The Earth Test Point Of Galvanised Iron / Steel Of Size 75Mm X 75Mm X 25Mm, Supplying And Laying Charcoal Stone Aggregate ) Chamber And Mild Steel Angle Iron Frame 40X40x3mm And Rcc Cover 40Mm Thick ( 1:2:4 ) Type B-1 Using 20Mm Graded Crushed Stone Aggregate Reinforced With 8Mm Dia Tmt Bars @ 75Mm O / O Both Ways With Mild Steel Handle 12Mm Dia, Pgi Funnel With Wire Mesh, 20 Mm Dia Gi Pipe Light Grade For Watering All As Shownin Electrical Plate No.3 Of Mes Ssr Part - 1 38 Supply, Laying And Testing Cable Xlpe Insulated , Screened, Pvc Bedded, Galvanized Steel Strip Or Wire Armoured, Electric Power Cables ( Heavy Duty ) 1100 Volts Grade With Stranded Aluminium Conductor Of Size 25 Sq Mm 4 Core All As Specified. 39 M&L For Boring Of Holes Of 200 Mm Dia Under The Road / Hard Standing By Horizontal Boring Method 2 Mtr Below The Surface For Fixing Requiste 2 Nos. All Equipments & Machinery Required To Carry Out The Work Will Be Provided By The Contractor ( If Due To Any Obstruction During Boring, Reboring Has To Be Done The Same Will Be Done By The Contractor At His Own Cost The Rates Deem To Cover The Same ) Complete All As Specified And Directed. 40 Supply And Laying Sub Class B Bricks ( Old Size ) Laid Flat In Trenches As Cable Covers All As Specified And Directed 41 Excavation In Trenches Not Exc 1.5 M Wide And Not Exc1.5 M In Depth And Getting Out In Soft / Loose Soil As In Foundation All As Required And Directed 42 M&L For Returning, Filling In, Including Spreading, Leveling, Watering And Well Ramming In Layers Not Exc 25 Cm Thick Complete All As Directed. 43 Removal Excavated Material ( Soil ) Not Exc 50M And Depositing Where Directed At A Level Not Exc 1.5M Above The Starting Point Complete All As Directed. 44 M&L For Cement Concrete 1:2:4 Type B-2 ( Using 40Mm Graded Stone Agg ) 100 Mm Thick As In Floor And Finish Concrete Surface Even And Smooth Without Using Extra Cost, Complete All As Specified. 45 M&L For Cement Concrete 1:4:8 Type D-2 ( Using 40Mm Graded Stone Agg ) 100 Mm Thick As In Floor, Complete All As Specified. 46 M&L For Rcc ( M-25 Design Mix ) ( 20Mm Graded Stone Aggregate ) As In Foundations, Including Rafts, Footings, Foundation Beams, Plinth Beams, Bases For Columns, Etc Basement Slabs, Under-Reamed Piles And Mass Concreate Etc Complete All As Specified And Directed. 47 M&L For Rcc ( M-25 Design Mix ) ( 20Mm Graded Stone Aggregate ) As In Columns, Pillars, Posts And Struts Etc Complete All As Specified And Directed. 48 M&L For Form Work To Sides Of Concreate Foundations, Footings, Bases Of Columns, Raft And Raft Beams, Sides And Soffits ( If Any ) Of Foundation And Plinth Beams, And Similar Works Vertical Or To Batter On Fair Finished Surfaces Foundation 49 M&L For Form Work To Sides Of Columns, Pillars, Posts, Struts, Piers And Stanchions On Fair Finished Surfaces 50 S&F For 10 Dia And Over Mild Steel Tmt Reinforcement Bars And Spacers Cut To Length, Bent To Shape Required Including Cranking, Bending, Blinding With And Including Mild Steel Wire ( Annealed ) Not Less Than 0.9 Mm Dia And Necessary Welding To Reinforcement Complete All As Specified And Directed. 51 S&F For 5 Dia And Over Upto Including 10 Mm Dia Mild Steel Tmt Reinforcement Bars As In Stirrups, Spacers And Blinders Etc Complete All As Specified And Directed. 52 M&L For Rendering 10 Mm Thick In Cement Mortar ( 1:4 ) On Fair Faces Or Brick Work Or Concrete Surfaces, Finished Even And Smooth Without Using Extra Cement And Mixed With Water Proofing Compound @ 3% By Weight Of Cement. ( Note: Wpc Will Be Measured And Paid Seperately ) 53 M&L For Preparation Of New Plastered Surfaces Of Walls And Applying Two Coats Of Cement Base Paint Over A Coat Of Primer Etc Complete All As Specified. 54 S&F Roof Trusses ( Framed ) , Trussed, Purlins, Crane Gantries, Rails And Fastenings And Heavy Bracket Framing ( Beam, Tee, Angle, Channel Or Flat Sections ) Including Distance Pieces, Cleats Etc Complete All As Specified And Directed. 55 M&L For Valve Pit Chamber Of Size 1050Mm X 1050Mm X 1050Mm ( Internal Dimention ) Complete Including Excavation And Earth Work, Pcc 1:4:8, Type D-2 Using 40Mm Graded Stone Aggregate, Brick Work In Cement Mortar 1:6, Plastering In Cement Mortar 1:4 ( Internally ) And Including 3Mm Thick Mild Steel Sheet Cover And Painting With Two Coat Of Synthetic Enamel Paint Over A Coat Of Red Oxide Primer Complete All As Specified And Directed. 56 Demolition Of Cement Concrete ( Un-Reinforced ) In Ground Floors And Pavings Not Exceeding 15Cm Thickness ( Below And Above Ground Level ) And Removing The Unserviceable Materials To A Distance Not Exceeding 100M All As Specified And As Directed. 57 M & L For Pcc 1:2:4 Type B2 Using 40 Mm Graded Stone Aggregate As In Sub Base / Mass Concrete Complete All As Specified And Directed. 58 M & L For 20 To 25 Mm Thick Machine Cut Kota Stone Slab Flooring, Landing, Steps And Plateformover And Including 20Mm Thick Screed Bed In Cement Mortar 1:4, Laid And Jointed With Grey Cement Slurry Mixed With Pigment To Match With Shade Of Slab Including Rubbing Andgrinding And Polishingto Achive Mirror Finish Complete All As Specified And Directed. 59 M & Lfor 20 To 25 Mm Thick Machine Cut Kota Stone Slab On Vertical Surfaces Such As Skirting, Risers Of Step, Dado Etcover And Including 10Mm Thick Bearing Plaster In Cement Mortar 1:3, Laid And Jointed With Grey Cement Slurry Mixed With Pigment To Match With Shade Of Slab Including Rubbing And Granite Polishing Complete All As Specified And Directed. 60 S&F Framed Work As In Doors Or Gates Of Angle Or Other Section With Gusset Plates, Rails, Braces, Etc., Complete, Drilled For Fixing Of Steel Sheeting Or Othercovering. Doors, Etc. To Be Prepared For Hanging Or Sliding With And Including Either Hooks And Hinges Or Steel Hanging Door Fittings ( Exclusive Of Steel Sheeting Or Other Covering, Running Rails And Guides ) Andhanging; Also Fastening And Fixing Complete 61 M&Lfor Pcc ( 1:2:4 ) Type B-1Using20 Mm Gradedstone Aggregates As In Filling On Holes In Walls, Bed Block For Inserting Hold Fast And Copingincluding Necessary Form Workcomplete All As Specified And Directed. { The Rate Is Deemed To Be Inclusive Of Form Work } 62 Excavation Over Area, N Exc 1.50 Mtr Deep And Getting Out In Soft Loose Soil Complete All As Specified And Directed 63 Removing Excavated Soil Exc 1.50 Km But N. Exc 5 Km And Deposited Wherever Directed 64 M&L For Hardcore Of Gauge N Exc. 63 Mm, Deposited, Spread And Levelled In Layers N Exc. 15 Cm Thick, Watered And Rammed To A True Surface Complete All As Specified As Directed. 65 M&L For Pcc 1:2:4 Type B-2 Using 40 Mm Graded Stone Aggregate As In Foundation Filling And Mass Concrete Complete All As Specified As Directed. 66 M&L For Pcc 75Mm Thick Type C-1 , 1:3:6 Using 20Mm Graded Stone Aggregate As In Plinth Protection Complete All Specifiedas Directed. 67 Supply Onlyglass Dividing Strips 38 Mm Wide Fixed In Floorcomplete All As Specified And Directed 68 Demolition Of Brickwork Or Stone Boulder Masonry, Built In Cement Mortar Including All Quoins, Arches, Pillars, Etc., But Excluding Ashlar Facings, Dressed Stonework And Precast Concrete Articles All As Specified And As Directed. 69 M&L For Brick Work With Sub Class B Modular Brick Straight Or Curved On Plan Exc. 6 M Mean Radius Built In Cement Mortar 1:6 Complete. 70 Taking Down Cement Plaster On Brick Or Stone Walls, Etc, Incl Raking Out Joints, Hacking For Key, Scrubbing Down With Water, Etc & Prepare To Receive New Plaster Complete All As Specified And Directed 71 M&L For 15Mm Thick Rendering In Cm 1:3 On Surfaces Of Brick, Concrete Wall, Chajja Surface Finished Even And Smooth Using Extra Cement With 2% Wpc By Weight Of Cement, Appling Two Coat Of Polymer Modified And Cementitious, Elastomemric Waterproofing Coating 1Mm Thick Shall Measure And Paid Seprately Under Respective Item Of As Supply Only Complete All As Specified And Directed 72 Supply Only Liquid Water Proofing Compound 73 M&L For 15Mm Thick Rendering In Cm 1:4 On Fair Faces Of Brick Work, Surfaces Finished Even And Faircomplete All As Specified And Directed 74 M&L For Rendering 5 Mm Thick On Concrete Surfaces In Ceiling , In Cement And Sand Mortar 1:3Top Surfaces Finished Even And Smooth Without Using Extra Cement Complete All As Specified 75 M&L For Preparation Of New Plastered Or Unplastered Surafces Of Ceilings And Applying Three Coats Of White Wash On Ceilingincluding Washing Floors, Cleaning Glass, Joinery, Electrical Fittings, Wiring Etc. , Of Drops And Splashes Complete All As Specified . 76 M&L For Preparation Of New Plastered Surface Of Wall And Applying Three Coats Of Whitewash On Surface Of Wall Incl Cornice Etc Complete All As Specified And Directed 77 M&L For Brooming Down Plastered Or Unplastered Old Decoratedsurface Of Wall Incl Cornice Etc And Applying Two Coat Of Whitewash Complete All As Specified And Directed 78 Taking Down Chowkhats Or Frames N. Exc 1.5 Sqm Each ( Without Taking Off Shutter From The Frame ) Complete. 79 All As Per Srl Item No-72But Exc. 1.5 Sqm But Not Exceeding 4 Sqm Each Complete. 80 S & F Factory Made Steel Window With Side Hung Shutter Including Box Type Hinges With Steel Handle, Steel Peg Stay, Hold Fast, Complete With Glazing Bar, Dovetailed Or Welded Complete. 81 S & Ffactory Made Steel Window With Side Hung Shutter Including Box Type Hinges With Steel Handle, Steel Peg Stay, Hold Fast Complete With Ms Flat For Fixing Wire Mesh, Dovetailed Or Welded Complete . 82 Supply Only 3 Mm Thick Plain Sheet Glass / Pin Headedfigured Glass Ordinary Quality And Glazing With Oil Putty Or Wooden Beads / Steel Frame In Square Area N. Exc. 0.5 Sqm In Each Pane Complete . Note :- Fixing Only Rate Is Included In Window / Door Shutter Items Considered Therein 83 Supply & Fixing Stainless Steel Wire Cloth 0.36 Mm Nominal Dia Of Wire And Average Width Of Aperture 1.40 Mm And Fixed With Stainless Steel Wire Stapplescomplete All As Specified And Directed 84 S & F 125X60 Mm Pressed Steel Frames For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plate, Etc., Complete, As Specified, Supplied And Fixed 85 S&F Flush Shutters 30Mm Thick, Solid Core Construction, With Block Board Core & Plywood Face Panels, Commercial Type On Both Sides Complete All As Specified And Directed. 86 S & F 35 Mm Thick Of First Class Hardwood Glazed And Skeleton Shutters, Open Rebated And Prepare To Receive Glass, Gauge, Etc., ( With Sash Bars ) Size Of Members Of Shutters As Specified In Ssr Part-I Section 8 Clause 8.20 ( A ) Supplied And Fitted To Chowkats Complete All As Specified And Directed. 87 S&F Ms Flat Iron As In Hold Fast Etc And Similar Work Incuding Making Shape, Drilling Holes Etc, Confriming To Fe 290 Ged E-165 88 M&L For Pcc ( 1:3:6 ) Type C1 ( Using 20Mm Graded Stone Aggregate ) As In Bed Plate For Fixing Holdfast Etc All As Specified And Directed. 89 S&F Aluminium Alloy Wire Cloth, 0.45 Mm Nominal Dia Of Wire And Average Width Of Aperture 1.40Mm And Fixed With Beading To Wooden Frames All As Specified And As Directed. 90 S&F Aluminium Alloy Wire Cloth, 0.45 Mm Nominal Dia Of Wire And Average Width Of Aperture 1.40Mm And Fixed With Beading To Wooden Frames As In Repairs All As Specified And As Directed. 91 S&F Aluminium Anodised Barrel Tower Bolts Of Extruded Section Of Length Of Bolt 200Mm All As Specified And As Directed. 92 Supply Only Butt Hinges, Extruded Aluminium Alloy With Galvanised Mild Steel Hinge Pin, Anodised And Fixed, Type B-21 Of Size 100Mm All As Specified And As Directed. 93 S&F Aluminium Handles, Cast Type, Anodised Of Size 100Mm All As Specified And As Directed. 94 S&F 300 Mm Length Aluminium Alloy, Anodised, Sliding Door Bolts With Hasp, Staple ( Bolt Type ) And Fixing Clips Of Sheet, Cast Or Extruded Sections And Fixing Bolts And Sliding Bolts Of Extruded Sections Or Cast Aluminium Alloy And Fixed Of Length Of Bolt 300Mmall As Specified And As Directed. 95 M&L For Preparation Of Old Painted Surfaces Of Wood And Wood Based Materials Of Any Description Over 10 Cm Width Or Girth Not Otherwise Described And Applying One Coat Of Synthetic Enammel Paint. 96 M&L For Preparation Of Old Painted Steel Surfaces And Applying One Coat Of Steel Painting Complete All As Specified And Directed. 97 M&L For Preparation Of New Steel Surfaces And Applying Two Coat Of Steel Paint Including Primer On Steel Surfaces Complete All As Specified And Directed. 98 M&L For Surface Of Any Discription Not Otherwise Describedover 10 Cm Width Or Girth On New Untreated Surface With Two Coats Of Synthetic Enammelled Painting Over One Coat Pink Primer On Wooden Surface Complete All As Spd & Directed. 99 S&F In Repair Rubber Bead For Wooden Door 100 Dismantling Of Plain Or Corrugated Steel Sheeting, Any Gauge, Thickness, Including Nainital Or Similar Pattern Roof Coverings Complete All As Specified And Directed 101 S&F Pre-Painted Galvalume Aluminum Zinc Coating Gi Based Corrugated Steel Sheet 0.50Mm Thick Of An Colour Having Tensil Strength Of 550 Mpa As In Roof Covering To Wall Fixed With Self Tapping Screws As Specified. 102 Taking Down Carefully Aluminium Battenpoint, Wiring For Light / Fan / Socket / Bell Or Power Point Including. All Fittings I.E. Switch, Sockets, Ceiling Rose, Regulators, Batten Holders, Etc. Complete And Making Good Disturbed Surfaces Of Wall / Floor To Match With The Surroundings Of Wall / Ceiling / Floor Etc Including Taking Down Old Light Fittings. Note :- ( I ) Contractors Quoted Rate Of This Item Deemed Inclusive Of Unscrewing Of The Serviceable Fittings And Fixture As Directed And Deposit In Mes Store Yard. ( Ii ) Quoted Rate Also Deem To Be Included Cost Of Cutting Chases For Taking Out Concealed Conduit And Nitch For Terminal Box. ( Iii ) Decision Of Ge Shall Be Final And Binding In Respect Of Serviceability Of Fittings / Fixture. 103 M & L For Point Wiring Complete With 1.5 Sqmm Single Core Pvc Insulated Frls Cable 1100 Volts Grade With Multi Stranded Copper Conductor Drawn Through New Pvc Concealed Conduit Medium Grade, Isi Markedand Including Provision Of 1.5 Sqmm Pvc Insulated Copper Cable Frls As Earth Continuty, Fabricated Branded Modular Metal Flush Box Duly Make Embossed, Concealed In Walls With Suitable Modular Inner And Outer Plate For Housing Switches , Socket Outlet And Fan Regulators Etc, Complete All As Specified And As Directed For The Followings:- 104 ( A ) One Light / Fan / Bellpoint Controlled By One Switch Single Pole One Way 105 ( B ) All As Per Item No 97 Here-In-Before Butone3 Pin 6 Amp Switch Socket Out Let Independent . 106 ( C ) All As Per Item No -97 Here Inbefore But One 3 Pin 5 Amps Socket Outlet On The Same Board With Other Switch Complete . 107 All As Per Item No 97 Here-In-Before But Using 02 Nos. 4.0 Sq Mm Size For Main Cable And 01 No.4.0 Sq Mm Size As Earth Conductor For One 16 Amp Switch Socket Outlet On Independent Board. 108 Supply And Fix Switch Modular Flush 6A Single Pole One Way Isi Marked 109 Supply And Fix Modular Sockets 6 Amp 2 In 1 2 / 3 Pin Combined All As Specified And Directed. 110 Supply And Fix Switch Modular Flush Type 15 / 16 Amp Single Pole One Way 240 Volt One Module Isi Marked 111 Supply And Fix Modular Sockets 16Amp 2 In 1 3 / 5Pin Combined All As Specified And Directed. 112 Supply And Fix Ceiling Rose Surface Bakelite 60X25mm Three Terminal 113 S&F Led Batten Luminaire Surface Mounted, 4 Feet System Wattage Of 20 Watts, System Lumen Efficiency >90 Lumen / Watt, 6500Kandincluding Connectingfrom Ceiling Rose To Fitting Completeallas Specified And Directed. 114 Supply And Fix In Replcementflood Light 30 Watt 240 Volt 50 Htz 3000 / 6500K 120 Lumen / Wattip-65Complete All As Spd And Directed. 115 Supply & Fix Mcb Db Spn 8 Way, Double Door, Ip-43, Ik-09, Isolated Neutral Bar And Fixed Flush To Wall And Suitable For Universal Mounting Completeall As Specified And Directed. 116 Supply And Fix Mcb, Single Pole And Neutral, 230 Volts, 32 To 40 Amp Rating, C Series Fixed In Dbs Catered Here-In-Before. Make Legrand / Hager / Siemense 117 Supply And Fix Mcb Sp 6-32 Amps 240 Volts 10 Ka 50 Hz C Curve Complete All As Specified And Directed By Engineer In Charge 118 Supply And Fix Wall Mounted Fan 400Mm Size, 230 Volts , 50 Hz 1420 Rpm With 90 Degree Oscillation And Having Speed Control By Pull Cord System Complete All As Specified And Directed. 119 M&L For Earthing Complete With Galvanised Steel Earth Plate Electrode 60 X 60 Cm X 6 Mm Thick, Buried Directly In Ground ( Earth Pit Not Less Than 2.25 Metres Deep Below Ground Level ) With Top Edge Of The Plate Not Less Than 1.5 Metres Below Normal Ground Level, Connected To Galvanised Iron Wire 4Mm Dia Asearth Lead Wire By Means Of Bolts, Nuts, Check Nuts And Washers Of Galvanised Iron Or Steel All As Shown In Electrical Plate No. 3, Mes Ssr Part I- 2009 With 15 Mm Dia Medium Grade Gi Pipe As A Protection To Earthing Lead And 20 Mm Dia Medium Grade Gi Pipe For Watering Purpose Including Excavation & Earth Work In Any Type Of Soil, Funnel, Wire Mesh, Rcc Pit With Cover, Cast Iron Frame Complete And Connected To Earthing Test Point All As Specified Or Indicated Including Testing On Completion. Notes ( I ) The Concrete Pit Shall Be Pcc ( 1:3:6 ) Type C-1, 40Mm Thick Precast Cover Slab Of Rcc With Suitable Mild Steel Handle In Lieu Of Cast Iron Cover Shown In Electrical Plate No 3 Of Mes Ssr Part-I ( Ii ) Pcc Pit Shall Be Provide At Least 500 Mm Away From The Earth Pit And Not On Just On The Eath Pit And Extra Cost Of Additional Length Of Water Pipes And Fittings Junction Etc Shall Be Deemed To Be Included In The Rate. ( Iii ) Item Includes The Cost Of 7.5 Metre Earth Lead Wire Andgi Pipe For Protection Of Earth Wire. Any Varriation In Quantity Shall Be Adjusted. 120 Supply, Laying, Jointing & Testing Of Underground Lt Cables Xlpe Insulated, Pvc Sheathed, Aluminium Conductors, Multistranded, Armoured Heavy Duty 1100 Volt Grade Cross Sectional Area 16 Sqmm 2 Core Laid In Trenches / Ducts / Along Poles / Through Pipe Under Road Etc With New Aluminium Lugs.
