Concertina Coil, Barbed Wire And Chain Link Fencing Works At Various Locations Of Cpcl Manali , Concertina Coil, Barbed Wire & Chain Lin , Concertina Coil Fencing: Providing And Fixing 750Mm Dia Green Colour Painted Razor Type Concertina Fencing With All Required Clips, Pins, Etc As Per The Specifications(Each Concertina Coil Piece Stretch To 9M Length) Concertina Coil Shall Be Fixed To The M.S. Angle With 4 Rows Of Same Concertina Runner Wires Over Exisiting X Type Angle Supports As Per Drawings. Rate Shall Be Quoted On Running Metre Of Compound Wall Basis .(A) Diameter Of Coil: 750Mm, Number Of Circles And Number Of Clips Are 72 And 180 In Each 9M Of Length. (B) Central Core Wire: Core Wire Shall Be Of 2.6Mm Diameter Made Of High Carbon Spring Steel Of High Tensile Strength Having Minimum Galvanized Coating Thickness Equivalent To 230 Grams Per Sq.M. (C) Razor Strip: 0.5Mm Thick Hot Dip Galvanized And Of Width 19Mm Having Series Of Barbed Punched All Along The Length At Regular Intervals Having Minimum Galvanized Thickness Of 12 Microns. Hardness Of Tape Should Be Between 137-180 Vpn (Victor Penetration Number) (D) Clips: 1.5Mm Thick Made Out Of Stainless Steel.(E) Runner Wire: Shall Be Of Same Specifications As Of Central Core Wire. Dismantling Of Existing / Damaged Coil And Returing To Scrap Yard To Be Carried Out If Required. , Same As #10 Only For Installation Without Material Supply. Concertina Coil Fencing Materials Will Be Supplied By Cpcl At Free Of Cost. Transportation Of The Free Issue Materials From Issue Points/ Ware House To Work Site Is Under Contractors Scope. Dismantling Of Existing/Damaged Coil And Returing To Scrap Yard To Be Carried Out If Required. , Supplying, Fixing And Tensioning In Position On Rcc Posts / Ms X Or Y Or Any Other Shape Angle Supports,12 Gauge, 2Ply, 4Points, Gi Barbed Wire Designation A-1 Confirming To Is:278 In Horizontal Rows For Barbed Wire Fencing At Ground Level Or Above Compound Wall In All Heights, Etc With Necessary Gi Staples,Clips And Pins, Gi Straining Bolts And Binding Wire, Turn Buckles, Etc. Complete As Per Specifications And Directions Of Engineer In Charge. Dismantling Of Existing/Damaged Barbed Wire And Returing To Scrap Yard To Be Carried Out If Required. , Supplying And Fixing At Site Chain Link Wire Net Fencing With Chain Link Fence Fabric Of 50X50 Mm Diamond Mesh Of 2.5Mm Dia Gi Innerwire Insulated With Minimum 1.5Mm Pvc To Achieve Outer Dia Not Less Than 4Mm To Intermediate, Corner, Straining, Starting Or End Post Of Ms Angles/Post/Strut And One Horizontal Strand Of 8 Swg (4Mm) Dia Gi Inner Wire Insulated With Pvc For Tension In Chain Link (At Middle) , Gi Staples For Fixing Chainlink In The Intermediate Posts And 10Mm Dia 175Mm Long Hook Bolts (Threaded Portion Being 75Mm Long Minimum) For Fixing Each Link Of The Chain Link (As Required); With All Labour And Materials But Excluding Cost Of All Ms Angle Post, Etc., Complete As Per Drawings And Directions Of Engineer-In-Charge. Dismantling Of Existing/Damaged Chain Link Wire Net Fencing And Returing To Scrap Yard To Be Carried Out If Required. , Supplying, Transporting, Storing, Fabricating And Fixing In Position Ms Angle Iron Post & Strut / Steel Inserts Of Required Size As Shown In Drawing/As Per Eic Instructions, Including Fabrication To Any Shape Made Out Of Flats, Plates, Rolled Sections, Sleeves, Pipes Etc. Including Bottom To Be Split And Bent At Right Angle In Opposite Direction For 10Cm Length And Drilling Holes Upto 10 Mm Dia. Etc As Required, Providing Necessary Templates, Staging, Cutting, Straightening, If Required, Bolting, Welding As Required And Embedding In Position On Both Plain, Reinforced Cement Concrete Members Inclusive Of Adjusting Shuttering & Reinforcement/Any Other Fixture, Welding Where Ever Necessary, Tying And Holding To Correct Level, Line And Position, Any Auxilliary Dummy Structures To Support The Heavy Inserts, & Painting With One Shop Coat & One Field Coat Of Inorganic Zinc Silicate Primer (Dft 25 Microns Each) And Finsihing With Two Coats Of Anti Rust Epoxy Paint (Dft 75 Microns Each) Of Approved Brand And Colour ,Etc Complete For All Heights & Depths As Per Drawing, Specification And Direction Of Engineer-In-Charge. Dismantling Of Existing/Damaged Steel Supports And Returing To Scrap Yard To Be Carried Out If Required.
