Construction Of Medicine Store Cum Radiology Building At Monteswar Kadambini Block Primary Health Centre, Monteswar, Purba-Bardhaman-- 1 Earth Work In Excavation Of Foundation Trenches Or Drains In All Sorts Of Soil ( Including Mixed Soil But Excluding Latarite And Sand Stone ) But Including Removing Spreading Or Stack- Ing The Spoils Within In A Lead Of 75M. As Directed And Including Trimming The Of Trenches, Leveling Dressing And Rammingsidesthe Bottom, Bailing Out Water Etc. As Required Complete. A ) Depth Of Excavation Not Exceeding 1500 Mm 2 Earth Work In Filling In Foundation Trenches Or Plinth With Good Earth, In Layers Not Exceeding 150 Mm. Including Watering And Ramming Etc. Layer By Layer Complete. ( Payment To Be Made On The Basis Of Measurement Of Finished Quantity Of Work ) ( A ) With Earth Obtained From Excavation Of Foundation 3 Filling In Foundation Or Plinth In Layer Not Exceeding 15 Cm As Directed And Consolidating The Same By Through Saturation With Water Ramming Complete Including The Cost Of Supply Of Sand. 1 ) With Fine Sand. 4 Single Brick Flat Soling Of Picked Jhama Bricks Including Ramming And Dressing Bed To Proper Level, And Filling Joints With Powered Earth Or Local Sand. 5 ( I ) Cement Concrete With Graded Stone Ballast ( 40 Mm Size Excluding Shuttering ) In Ground Floor ( A ) [ Pakur Variety ] ( A ) 1:3:6 Proportion 6 Oridinary Cement Concrete ( 3:1.5:1 ) With Graded Stone Chips ( 20 Mm Size ) Nominal Size Excluding Shuttering And Reinforcement , If Any In Ground Floor As Per Relevant Is Code. ( A ) Pakur Variety 7 Hire And Labour Charges For Shuttering With Centering And Necessary Staging Upto 4 Mtr Using Approved About Props And Thick Hard Wood Planks Of Approved Thickness With Required Bracing For Concrete Slabs , Beams, Columns, Lintels, Curved Or Straight Including Fitting, Fixing & Striking Out After Completion Of Works ( Upto Roof Of Ground Floor ) A ) 25 Mm To 30 Mm Thick Wooden Shuttering As Per Decision & Direction Of Engineering-In-Charge.Without Prop 8 With Prop 9 Reinforcement For Reinforced Concrete Work In All Sorts Of Structures Including Distribution Bars, Stirrups, Binders Etc. , Initial Straightening And Removal Of Loose Rust ( If Necessary ) , Cutting To Requisite Length, Hooking And Bending To Correct Shape, Placing In Proper Position And Binding With 16 Gauge Black Annealed Wire At Every Inter-Section, Complete As Per Drawing And Direction. A ) For Works In Foundation Basement Upto Roof Of Ground Floor / Upto 4 M . ( I ) Tor Steel / Mild Steel Ii. Jsw / Jspl / Shyam / Srmb / Bmasl / Elecrosteel / Ssl 10 250 Mm Thick Brick Work With Fly Ash Bricks ( 250Mmx125mmx75mm ) As Per Is 12894:2002 In Cement Mortar ( 1:6 ) In Foundation 11 In Superstructure 12 ( A ) 125 Mm. Thick Flyash Brick Work As Per Is 12894:2002 In Cement Mortar ( 1:4 ) In Ground Floor. 13 Plaster ( To Wall, Floor, Ceiling Etc. ) With Sand And Cement Mortar Including Rounding Off Or Chamfering Corners As Directed And Raking Out Joints Including Throating, Nosing And Drip Course, Scaffolding / Staging Where Necessary ( Ground Floor ) . [ Excluding Cost Of Chipping Over Concrete Surface ] 1:6 15 Mm Thk 14 1:6 20 Mm Thk 15 1:4 10 Mm Thk 16 Neat Cement Punning About 1.5Mm Thick In Wall, Dado, Window, Ceiling, Floor, Drain Etc. 17 Supplying And Laying True To Line And Level Vitrified Tiles Of Approved Brand ( Size Not Less Than 600 Mm X 600 Mm X 10 Mm Thick ) In Floor, Skirting Etc. Set In 20 Mm Sand Cement Mortar ( 1:4 ) And 2 Mm Thick Cement Slurry Back Side Of Tiles Using Cement @ 2.91Kg. / Sqm Or Using Polymerised Adhesive ( 6 Mm Thick Layer Applied Directly Over Finished Artificial Stone Floor / Mosaic Etc Without Any Backing Course ) Laid Afterapplication Slurry Using 1.75 Kg Of Cement Per Sqm Below Mortar Only, Joints Grouted With Admixture Of White Cement And Colouring Pigment To Match With Colour Of Tiles / Epoxy Grout Materials Of Approved Make As Directed And Removal Of Wax Coating Of Top Surface Of Tiles With Warm Water And Polishing The Tiles Using Soft And Dry Cloth Upto Mirror Finish Complete Including The Cost Of Materials, Labour And All Other Incidental Charges Complete True To The Manufacturers Specification And Direction Of Engineer-In-Charge. ( White Cement, Synthetic Adhesive And Grout Material To Be Supplied By The Contra Conc ( I ) With Application Slurry @1.75 Kg / Sq.M, 20 Mm Sand Cement Mortar ( 1:4 ) & 2 Mm Thick Cement Slurry At Back Side Of Tiles, 0.2 Kg / Sq.M White Cement For Joint Filling With Pigment. ( B ) Light Colour 18 Supplying, Fitting & Fixing 1St Quality Ceramic Tiles In Walls And Floors To Match With The Existing Work & 4 Nos. Of Key Stones ( 10Mm ) Fixed With Araldite At The Back Of Each Tile & Finishing The Joints With White Cement Mixed With Colouring Oxide If Required To Match The Colour Of Tiles Including Roughening Of Concrete Surface, If Necessary Or By Synthetic Adhesive & Grout Materials Etc. With Sand Cement Mortar ( 1:3 ) 15 Mm Thick & 2 Mm Thick Cement Slurry At Back Side Of Tiles Using Cement @ 2.91 Kg / Sq.M & Joint Filling Using White Cement Slurry @ 0.20Kg / Sq.M. ( B ) Wall ( A ) Area Of Each Tile Upto 0.09 Sq.M ( I ) Coloured Decorative 19 Supplying, Fitting & Fixing Granite Slabs 15Mm To 18 Mm. Thick With Uniform Texture & Without Decorative Veins In Columns, Wall, Facia Etc. With 15 Mm Thick [ Avg ] Cement Mortar ( 1:2 ) Including Making Suitable Arrangements To Hold The Stones Properly By Brass / Copper Hooks Including Pointing Incement Mortar ( 1:2 ) ( 1 White Cement : 2 Marble Dust ) With Admixture Of Pigment Matching The Stone Shades All Complete As Per Direction Of The Engineer-In-Charge Including Cost Of All Materials, Labours, Scaffolding, Staging , Curing And Roughening Of Concrete Surface Complete. [ Using Cement Slurry At Backside Of Granite @ 4.4 Kg / Sq.M & White Cement Slurry For Joint Filling @ 1.8 Kg / Sq.M ] ( Ground Floor ) 20 Supplying& Laying 20 Mm Designer Chequered Tiles Of Any Shade And Of Approved Quality As Per Is: 1237: 1980 Laid In Patterns As Directed In Pavement, Footpath Including Necessary Underlay 25 Mm Thick Average Cement Mortar ( 1:3 ) Complete In All Respect With All Labour And Materials [ Using Cement Slurry @ 4.4 Kg / Sq.M At Back Side Of Tiles. Cement Of Mortar & Slurry Will Be Supplied By The Department. Border Concrete If Necessary To Be Paid Separately ] . 21 Acrylic Distemper To Interior Wall, Ceiling With A Coat Of Solvent Based Interior Grade Acrylic Primer ( As Per Manufacturers Specification ) Including Cleaning And Smoothning Of Surface. Two Coats 22 Applying Exterior Grade Acrylic Primer Of Approved Quality And Brand On Plastered Or Cencrete Surface Old Or New Surface To Receive Decorative Textured ( Matt Finish ) Or Smooth Finish Acrylic Exterior Emulsion Paint Including Scraping And Preparing The Surface Throughly, Complete As Per Manufacturers Specification And As Per Direction Of The Eic. A ) One Coat 23 Protective And Decorative Acrylic Exterior Emulsion Paint Of Approved Quality, As Per Manufacturers Specification And As Per Direction Of Eic To Be Applied Over Acrylic Primer As Required. The Rate Includes Cost Of Material, Labour, Scaffolding And All Incidental Charges But Excluding The Cost Of Primer. In Ground Floor ( Two Coat ) B ) Premium 100% Acrylic Emulsion 24 Wood Work In Door And Window Frame Fitted And Fixed In Position Complete Including A Protective Coat Of Painting At The Contact Surface Of The Frame Exluding Cost Of Concrete, Iron Butt Hinges And M.S Clamps. ( The Quantum Should Be Correted Upto Three Decimals ) . ( E ) Sal : Malayasian 25 Panel Shutters Of Door And Window, As Per Design ( Each Panel Consisting Of Single Plank Without Joint ) , Including Fitting And Fixing The Same In Position But Excluding The Cost Of Hinge And Other Fittings. ( In Case Of Non-Supply Of Single Plank, Penal Rate Of Reduction Of 20% Will Be Made ) 35Mm Thick Shutters With 19Mm Thick Panel Of Size 30 To 45 Cm.Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. 26 Supplying Fitting And Fixing In Position Approved P.V.C. Doorframe ( Matt Finish ) Made Of Extruded P.V.C.Multichamber Hollow Section Having Dimensions 60Mm X5ommx 2Mm ( ±0.2Mm ) , Horizontal Section Will Be Joinedwith Vertical Section By Galvanised Steel Screws Afterinserting Two Number Steel Brackets As Reinforcementmaking Suitable Space For Placing Hinges, One Steel Tube40mm X 20Mm X 1.20 Mm Will Be Inserted On One Fullvertical Side Of The Frame ( Hinge Side ) As Reinforcement, The Frame Will Then Be Fixed In The Opening With The Help Ofp.V.C. Expandable Fastner Wooden Gutties Andgalvanisedsteel Screws Including Cost Of All Materials And Labour, Hirecharges Of Tools And Appliances, Carriage Of All Materials, Taxes And All Other Incidental Charges Complete. 27 Pvc Door Shutter-37 Mm Thick:- Supplying Fitting And Fixing P.V.C. Door Shutter Of Approved Quality & Shade In Position, The Style & Rail Of The P.V.C.Door Shutter Will Be Made Of Rigid P.V.C. Multicavity Hollow Chamber Of Suitable Size And Section With 2.0Mm ( ± 0.2Mm Wall Thickness, The Section Will Have 2Nos. Built In Beads, Horizontal & Vertical Section Shall Be Fixed To Each Other By Self Tapping Screws And 2 Nos. Of Solid Plastic Or M.S. Tubular Galvanised Brackets Of Length 200Mm X 80Mm And Other 100Mm X 100Mm Both 1.20 Mmin Each Comer Of Theshutter Frame For Placinghinges. Polymer Based Multicavity Hollowsection Of105mm X37mm With 2.0Mm ( ±0.2Mm ) Wall Thickness Will Be Fitted In The Middle As Lock Rail Reinforced By Solid Polymer Bar Of 200Mm Long At Both Ends & Screws For Both Sides. The Section Frame Will Then Be Fitted In By Prepanels Of Size 100Rnmx20mm, With Wall Thickness 1.2Mm ( ±0.2Mm ) And 2 Nos. Of 6Mm Dia Bright Rod Will Be Inserted Horizontally With Both Side Check And Nut System And Stretches Where Fixing Of Hinges / Hasp Bolt / Tower Bolt / Door Ring Are Required To Be Strong Enough To With Stand Wear And Tear. The Rate Is Inclusive Of Cost Of All Materials, Labour, And Hire Of Tools And Plants And Appliencies. Carriage Of All Materials Taxes And All Other Incidental Charges Complete.The Rate Is Exclusive Of Cost Of Hinges, Hasp Bolt.Tower Bolt.Door Ring Etc. 28 Collapsible Gate With 40Mm X 40Mm X 6Mm Tee As Top And Bottom Guide Rail, 20Mm X 10Mm X 2Mm Vertical Channels 100Mm Apart In Fully Stretched Position 20Mm X 5Mm M.S. Flats As Collapsible Bracings Properly Rivetted And Washered Including 38Mm Steel Rollers Including Locking Arrangements, Fitted And Fixed In Position With Lugs Set In Cement Concrete And Including Cutting Necessary Holes, Chasing Etc. In Walls, Floors Etc. And Making Good Damages Complete. 29 M.S. Or W.I. Ornamental Grill Of Approved Design, Joints Continuously Welded With M.S. Wi Flats And Bats Forwinding, Drillingetc.Fitted &Fixed Withnecessaryscrew Andlugsingroundfloor. A ) Grillweighing Above 10 Kg Upto 16 Kg / Sqm 30 Supplying Best Indian Sheet Glass Panes Set In Putty And Fitted And Fixed With Nails And Putty Complete. ( In All Floors For Internal Wall & Upto 6 M Height For External Wall ) ( Ii ) 4 Mm Thick 31 A ) Priming One Coat On Timber, Plastered Surface Withsynthetic Enamel / Oilbound Primerof Approved Quality Including Smoothening Surface By Sand Papering Etc. 32 B ) Priming One Coat On Steel Or Other Metalsurface With Synthetic Enamel / Oil Bound Primer Of Approved Quality Including Smoothening Surface By Sand Papering Etc 33 Painting With Best Qualitysynthetic Enamelpaint Of Approved Make And Brand Including Smoothening Surface By Sand Papering Etc Including Using Of A Approved Putty Etc On The Surface If Necessaryontimberorplasteredsurface ( Withotherthanhiglossof Approved Quality ) .I ) 2 Coats ( With Any Shade Except White ) 34 Painting With Best Qualitysynthetic Enamelpaint Of Approved Make And Brand Including Smoothening Surface By Sand Papering Etc Including Using Of A Approved Putty Etc On The Surface If Necessaryonsteelorothermetalsurface ( Withotherthanhiglossofapprovedquality ) .I ) 2 Coats ( With Any Shade Except White ) 35 Supplying, Fitting & Fixing Upvc Pipes A- Type And Fittings Conforming To Is:13592-1992 With All Necessary Clamps Nails, Including Making Holes In Walls, Floor Etc. Cutting Trenches In Any Soil Through Masonry Concrete Structures Etc If Necessary And Mending Good Damages Including Joining With Jointing Materails ( Spun Yarn, Valamoid / Bitumen / M-Seal Etc ) Complete. A ) Upvc Pipes: ( Ii ) 110 Mm. Dia. 36 B ) Upvc Fittings: A ) Plain Tee ( Ii ) 110 Mm. Dia. 37 Supplying, Fittingandfixingm.S.Clampsfordoorandwindowframemadeofflatbentbar, End Bifurcatedwithnecessaryscrewsetc.Bycementconcrete ( 1:2:4 ) Asperdirection. ( Costofcement Concrete With Paid Separately ) . ( B ) 40Mm X 6Mm, 200Mm Length 38 Iron Butt Hinges Of Approved Quality Fitted And Fixed With Steel Screws, With Isi Mark.100Mm. X 75Mm. X 3.50Mm. 39 ( A ) Irondoorringofapprovedqualityfittedandfixedwithnutandwashercomplete. A ) 50 Mm Dia. ( Window ) 40 B ) 75 Mm Dia ( Door ) 41 Iron Socket Bolt Of Approved Quality Fitted And Fixed Cmplete.150 Mm Long X 10 Mm Dia Bolt. 42 B ) 225 Mm Long X 10 Mm Dia Bolt. 43 I ) Iron Hasp Bolt Of Approved Quality Fitted And Fixed Complete ( Oxidised ) With 16Mm Dia Rod With Centre Bolt And Round Fitting. - ( C ) 300Mm Long.. 44 Anodised Aluminium Grip Handle With Base Plate Of Approved Quality Fitted And Fixed Complete.With Base Plate. 165Mm Grip X 12Mm Dia Rod X 42Mm Plate X 3.2Mm Thick. 45 Supplying, Fittingandfixinghingecleatinpositionincludingthecosthingeandotherfiffitngs. A ) With 75Mm. X 47Mm. X 1.70Mm Iron Butt-Hinge , Local Sal 46 ( A ) Supplying Godrej Mortice Lock Chromium Plated With Latch And Keys 4 Levers, Including Fitting And Fixing Complete. 47 Supplying, Fitting And Fixing Stainless Steel Railing Consist Of 38Mm Dia And 900Mm Height Vertical Balustrade At Every Two Alternative Steps, 50Mm Dia Top Rail, 3 ( Three ) Nos 19Mm Dia Horizontal Strainless Steel Pipe And Base / Cover Plate With Strainless Steel Grade 304 Containing 7.5% Nickle ( Interior Grade ) Brushed / Mat Finish, Complete As Per Direction Of The Engineer-In-Charge. Weight Of Strainless Steel Railing Per Metre 6.5 Kg ( Approx ) 48 Supplyingfittingapprovedtypeventilatorinpositionaftercuttingholesinwalls, Settingincement Mortar, Mendingdamagestowallandplasterandtwocoatsofpaintofapprovedbrandsandshade.Payment Of Mending Two Damages Of Wall & Plaster And Painting To Be Made Separately.R.C.C Ventilator Of 20 Mm. Thick - Upto 0.10 Sq.M. Area 49 Supplying, Fitting & Fixing Zn-Al Alloy ( 55% Al & 45% Zn ) Coating Of 150 Grams Per Sq. Metre ( Followed By Colour Coated On Both Side ) Steel Sheet Work Having Minimum Yield Strength Of 550 Mpa Of Trapizoidal Profile Of Approved Make ( Excluding The Supporting Frame Work ) Fitted And Fixed With 55 Mm & 25 Mm Self Tapping Screw, Epdm Washer 16 Mm Dia & 3 Mm Th. Washer Etc. Complete With 150 Mm End Lap And One Corrugation Minimum Side Lap. ( Payment To Be Made On Area Of Finished Work ) .In Roof With 0.5 Mm Thick Sheet 50 M.S. Structural Works In Columns, Beams Etc. With Simple Rolled Structural Members ( E.G. Joists, Angle, Channel Sections Conforming To Is: 226, Is: 808 & Sp ( 6 ) - 1964 Connected To One Another With Bracket, Gussets, Cleats As Per Design, Direction Of Engineer-Incharge Complete Including Cutting To Requisite Shape And Length, Fabrication With Necessary Bolting, Metal Arc Welding Conforming To Is: 816- 1969 & Is: 1995 Using Electrodes Of Approved Make And Brand Conforming To Is:814- 2004, Haulage, Hoisting And Erection All Complete. The Rate Includes The Cost Of Rolled Steel Section, Consumables Such As Electrodes, Gas And Hire Charge Of All Tools And Plants And Labour Required For The Work Including All Incidental Chages Such As Electricity Charges, Labour Insurance Charges Etc.For Structural Members Of Specified Sections Weighing Less Than 22.5 Kg. / M 51 Supplying, Fitting And Fixinggunmetal Wheel Valve Of Approved Brand And Make Tested To 21 Kg / Sq.Cm. ( For Water Lines Only ) .-32 Mm Dia 52 ( Viii ) 20 Mm Dia 53 ( Ix ) 15 Mm Dia 54 Supplying, Fitting&Fixingorissa Pattern Waterclosetinwhiteglazed Vitreouschinawareof Approved Makesupplied, Fittedfixedinposition Completeexcludingporstrap. ( Excludingcostofconcretefor Fitting ) I ) 530Mm X 410 Mm 55 Supplying, Fitting And Fixing 10 Litre P.V.C. Low-Down Cistern Conforming To I.S. Specification With P.V.C. Fittings Complete, C.I. Brackets Including Two Coats Of Painting To Bracket Etc. 56 Supplyingpvcwaterstoragetankofapprovedqualitywithclosedlid ( Black ) -Multilayer. E ) 2500 Litre Capacity. 57 Supplying, Fittingandfixingbestqualityindianmakemirror5.5Mmthickwithsilveringasperi.S.I. Specifications Supported On Fibre Glass Frame Ofany Colour, Frame Size 550 Mm X 400 Mm. 58 Supplying , Fitting And Fixing Glass Shelf With Alluminium Guard Rail. A ) Ordinary Type With 5.5 Mm Sheet Glass. ( I ) 450 Mm× 125 Mm 59 Wash Basin Vitreous China Of Approved Make ( Without Fittings ) Supplied, Fitted And Fixed In Position On 75Mm X 75 Mm X 75 Mm Wood Blocks And C.I. Brackets Including Two Coats Of Painting Of C.I. Brackets. ( Ii ) 550 Mm X 400 Mm Size 60 Hosting Plastic Storage Tank ( Ii ) Above 1500 Litre Up To 5000 Lit. Capacity. 61 Supplying, Fitting And Fixing Squating Plate With Integral Flushing In White Vitreous Chinaware Ofapproved Make In Cement Concrete ( 6:3:1 ) With Jhama Chips Complete. ( Payment Of Concrete Will Be Paid Seperately ) . ( I ) 450 Mm X 350 Mm 62 Supplying, Fitting And Fixing Flat Back Urinal ( Half Stall Urinal ) In White Vitreous Chinaware Of Approved Make In Position With Brass Screws On 75 Mm X 75 Mm X 75 Mm Wooden Blocks Complete. ( Ii ) 470 Mm X 280 Mm X 340 Mm 63 Supplying, Fitting And Fixing Approved Brand P.V.C. Connector White Flexible, With Both Ends Coupling With Heavy Brass C.P. Nut, 15 Mm Dia. ( V ) 900 Mm Long 64 Supplying, Fitting And Fixing Approved Brand 32 Mm Dia.P.V.C. Waste Pipe, With Pvc Coupling At One End Fitted With Necessary Clamps. ( Iv ) 1050 Mm Long 65 Supplying, Fittingandfixingcastironporstrapconformimgtoi.S.3989 / 2009And1729 / 2002 Includingleadcaulkedjointsandpaintingtwocoatstotheexposedsurface. ( Paintingtobepaid Seperately ) . B ) S Trap -Ii ) 75 Mm. 66 Supplying, Fitting And Fixing Pvc Pipes Of Approved Make Of Schedule 80 ( Medium Duty ) Conforming To Astmd-1785Andthreadedtomatchwithgipipesasperis:1239 ( Part-I ) .Withallnecessary Accessories, Specials Viz. Socket, Bend, Tee, Union, Cross, Elbo, Nipple, Longscrew, Reducingsocket, Reducingtee, Shortpiece Etc.Fitted Withholder Batsclamps, Includingcutting Pipes, Makingthreads, Fitting, Fixingetc.Completeinallrespectincludingcostofallnecessaryfittingsas Required, Jointing Materials And Two Coats Of Painting With Approved Paint In Any Position Above Ground. ( Paymentwillbemadeonthecentrelinemeasurementsoftotalpipelineincludingallspecials.No Separate Payment Will Be Made For Accesories, Specials. Payment For Painting Will Be Made Seperately ) ( A ) For Exposed Work Pvc Pipes 32Mm Dia. 67 Supplying, Fitting And Fixingg.I. Pipes Of Tata Make With All Necessary Accessories, Specials Viz. Socket, Bend, Tee, Union, Cross, Elbo, Nipple, Longscrew, Reducingsocket, Reducingtee, Shortpieceetc.Fitted Withholderbatsclamps, Includingcuttingpipes, Makingthreads, Fitting, Fixingetc.Completeinall Respect Including Costof Allnecessary Fittingsas Required, Jointingmaterials Andtwo Coatsof Painting With Approved Paint In Any Position Above Ground. ( Payment Will Be Made On The Centre Line Measurements Of Total Pipe Line Including All Specials.No Separate Payment Will Be Made For Accessories, Specials, Payment For Painting Will Be Made Separately ) 15 Mm Dia Medium Quality ( Concealed ) 68 B ) 20 Mm Dia Medium Quality ( Concealed ) 69 D ) 32 Mm Dia Medium Quality ( Exposed ) 70 Supplying, Fitting And Fixing Bib Cock / Stop Cock. ( A ) Chromium Plated Bib Cock Short Body ( Equivqlent To Code No 511 & Model . Tropical / Sumthing Special Of Essco Or Similar Brand15 Mm. 71 Supplying, Fitting And Fixing Approved Patent Vent Cowl I.C.I. Conforming To I.S.S And Painting Two Coats To The Exposed Surface With Approved Paint Complete. ( Payment Of Painting Will However Be Paid Seperately ) .- 100 Mm Dia. 72 ( A ) ( I ) Chromium Plated Round Shower With Revolving Joint 100 Mm Dia With Rubid Cleaning System ( Equivalent To Code No. 542 ( N ) & Model - Tropical / Sumthing Special Of Essco Or Similar Brand ) . 73 Supplying, Fitting And Fixing C.I. Round Grating. A ) 100 Mm Dia. 74 Supplying, Fitting And Fixing Pillar Cock Of Approved Make. A ) ( I ) Cp Pillar Cock - 15 Mm. ( Equivalent To Code No. 507 & Model - Tropical / Sumthing Special Of Essco Or Neo / Smile Brand Of Jhonson Or Similar Brand ) . 75 Soap Holder Ptmt ( Prayag Or Equivalent ) 76 Supplying, Fitting And Fixing Towel Rail With Two Brackets. ( A ) C.P. Over Brass ( I ) 25 Mm Dia. And 450 Mm Long 77 Construction Of Septic Tank Of Different Capacities As Per Approved Drawing With 1St Class Brick Work In Cement Mortar ( 1:4 ) Including Two 560 Mm Dia. R.C.C. Manhole Cover ( Heavy Type ) Of Approved Make Supplied, Fitted And Fixed In The 100Mm Thick R.C.C ( 1:1.5:3 ) Top Slab With Necessary Fittings, 20Mm Thick Cement Plaster ( 4 : 1 ) With Neat Cement Finish To The Internal Surfaces And 15 Mm Thick Cement Plaster ( 4: 1 ) To Outside Wall Upto 200 Mm Below G.L Floor Finished With 25 Mm Thick Grey Artificial Stone Over 100 Mm Thick R.C.C ( 1:1.5:3 ) Bottom Slab Including Supplying, Fitting And Fixing All Necessry Specials, Fittings, S.W. Tees, C.I. Foot Rest Etc. Including Excavation Earth In All Sorts Of Soil, Shoring, Bailing Out And Pumping Out Water As Necessary, Ramming, Dressing The Bed And Fefilling The Sides Of The Tanks With Earth, Removing Spoils, Filling Up The Chamber With Clear Water, Removing Foreign Materials From The Chamber And Including Constructing Attached Inspection Pit As Per Approved Drawing And Connecting All Necessary Pipes, Joints Etc. With Internal Plaster Work And Artificial Stone Flooring Is To Be Done With Admixture Of Water Proofing Compound @ 0.5% By Weight Of Cement With All Costs Of Labour And Materials. Note:- ( I ) Finished Level Of Septic Tank Should Be 400 Mm. From Ground Level. ( Ii ) Height Of 50 Mm. Ventilation Pipe &Mosquito Proof Mesh, Should Be Follwed As Per Is:2470, Part- I.Payment Will Be Made Separetly On The Basis Of Actual Height Based On Relevant I.S.Code. ( Iv ) For 50 Users A ) With Pakur Variety. Jsw / Jspl / Shyam / Srmb / Bmasl / Elecrosteel / Ssl 78 Construction Of Circular Soak Well 2.5 Metre Deep In All Types Of Sandy Soils With Dry Brick Work Upto 1.6 Metre From The Bottom Having 150 Mm Intermediate Cement Brick Work ( 1:4 ) Band All Round And Cement Brick Work ( 1:4 ) Upto 0.90 Metre From Top With 20Mm Thick Cement Plastering ( 1:4 ) To Inside Face Upto The Depth Of Cement Brick Work, 15Mm Thick Cement Plaster ( 1:4 ) On Outer Face From Top Of The Wellupto G.L. And 6 Mm Thick Cement Plaster ( 1:4 ) On Top Of The R.C.C. Cover Slab Including Filling Bottom 1.00 Metre Of Inside Of The Well With Brick Metal ( 50 Mm To 63 Mm Size ) Including R.C.C. Cover Slab Of 100 Mm Thick With Cement Conc ( 1:1.5:3 ) With Stone Chips With Necessary Reinforcement And Shuttering Including One 560 Mm Dia. R.C.C.Manhole Cover ( Heavy Type ) Of Approved Make Supplied, Fitted And Fixed In The Cover Slab With Necessary Fittings, Making Nacessary Arrangements For Pipe Connections, Excavation Of Well Including Shoring, Dewatering And Removing The Exess Earth From The Premises As Per Direction Complete In All Respect With All Costs Of Labour And Materials. With 250 Mm Thick Dry Brick Work And 250 Mm Thick Cement Brick Work ( 1:6 ) And 1.00M Inside Dia. Jsw / Jspl / Shyam / Srmb / Bmasl / Elecrosteel / Ssl 79 Electrification Works Distn. Wiring In 22 / 0.3 ( 1.5 Sqmm ) Single Core Stranded Fr Pvc Insulated & Unsheathed Single Core Stranded Copper Wire ( Kei / Havells Or Equivalent ) In 19 Mm Bore, 3 Mm Thick Polythen Pipe Complete With All Accessories Embedded In Wall To Light / Fan / Call Bell Points With Piano Key Type Switch ( Anchor Make ) Fixed On Sheet Metal ( 16 Swg ) Switch Board With Bakelite / Perspex ( Wall Matching Colour ) Top Cover ( 3 Mm Thick ) Flushed In Wall Incl. Mending Good Damages To Original Finish 2X22 / 0.3 ( Ph. & N ) And 1X22 / 0.3 As Ecc. Average Run 7 Mtr 80 Distn. Wiring In 22 / 0.3 ( 1.5 Sqmm ) Single Core Stranded Fr Pvc Insulated & Unsheathed Single Core Stranded Copper Wire ( Kei / Havells Or Equivalent ) In 19 Mm Bore, 3 Mm Thick Polythen Pipe Complete With All Accessories Embedded In Wall To 240 V 5A 3 Pin Plug Point Incl. S&F 240 V 5A 3 Pin Flush Type Plug Socket & Piano Key Type Switch ( Anchor Make ) Incl. S&F Earth Continuity Wire, Fixed On Sheet Metal ( 16 Swg ) Switch Board With Bakelite / Perspex ( Wall Matching Colour ) Top Cover ( 3 Mm Thick ) Flushed In Wall Incl. Mending Good Damages To Original Finish. 2X22 / 0.3 ( Ph. & N ) And 1X22 / 0.3 As Ecc On Board 81 Supplying And Drawing 1.1 Kv Single Core Stranded Fr Pvc Insulated & Unsheathed Single Core Stranded Copper Wire ( Kei / Havells Or Equivalent ) Of The Following Sizes In The Prelaid Polythene Pipe And By The Prelaid Gi Fish Wire And Making Necy. Connection As Required 3 X 22 / 0.3 ( 1.5 Sqmm ) 82 2X36 / 0.3 ( 2.5 Sqmm ) + 1X22 / 0.3 ( 1.5 Sqmm ) As Ecc 83 2X56 / 0.3 ( 4 Sqmm ) + 1X36 / 0.3 ( 2.5 Sqmm ) As Ecc 84 2X84 / 0.3 ( 6 Sqmm ) + 1X56 / 0.3 ( 4 Sqmm ) As Ecc 85 Finishing Of The Pvc Insulated Wire Ends By Socketting With Pin / Ring Type Copper Sockets And Insulated Tapes Etc., Including Supplying Sockets, Tapes. 2.5 Sqmm 86 4 Sqmm 87 6 Sqmm 88 1.5 Sqmm 89 Supplying And Fixing Polythene Pipe Complete With Fittings As Necy. Under Ceiling / Beam, Bound With 22 Swg Gi Binding Wire Incl. Supplying And Drawing 1X18 Swg Gi Wire As Fish Wire Inside The Pipes And Fittings And Providing 50 Mm Dia Disc Of Ms Sheet ( 20 Swg ) Having Colour Paint At One Face Fastened At The Load Point End Of The Polythene Pipe With Fish Wire ( Synchronizing With Roof / Beam Casting Work Of Building Construction ) 13Mm Dia 3Mm Thick Polythene Pipe 90 19Mm Dia 3Mm Thick Polythene Pipe 91 Cutting Channel Of Size ( 40 Mm X 40 Mm ) On Masonry Wall By Electric Operated Cutting Machine Incl. Supplying & Fixing Heavy Gauge 19 Mm, 3 Mm Thick Polythene Pipe By Means Of Anchoring Chemical ( Hilti / Sika ) And Gi U Hooks Of 8 Swg Incl. Supplying And Drawing 18 Swg Gi Wire As Fish Wire And Mending Good Damages To Original Finish By Using Own Tools And Tackles. 19 Mm Dia 3 Mm Thick Polythene Pipe Without Earth Continuity Wire 92 Supply & Fixing 240 V, 20A, Plug Socket With Separate 20 A Piano Key Type Switch ( Make Anchor Or Equivalent ) On Sheet Metal Switch Board Embedded In Wall Incl. S & F 150X100x65mm Ms ( 16Swg ) Switch Board And Bakelite / Perspex Top Cover Of 3Mm Thick By Brass Screws After Making Housing For Switch By Cutting Bakelite / Perspex Cover And Making Necessary Connections As Required. 93 Supply & Fixing 240 V, 2 Nos.6 A, Plug Socket With Separate 2 Nos. 6 A Piano Key Type Switch ( Make Anchor Or Equivalent ) On Sheet Metal Switch Board Embedded In Wall Incl. S & F 175X100x65mm Ms ( 16Swg ) Switch Board And Bakelite / Perspex Top Cover Of 3Mm Thick By Brass Screws After Making Housing For Switch By Cutting Bakelite / Perspex Cover And Making Necessary Connections As Required. 94 Supply & Fixing 240 V, 2 Nos.16 A, Plug Socket With Separate 2 Nos. 16 A Piano Key Type Switch ( Make Anchor Or Equivalent ) On Sheet Metal Switch Board Embedded In Wall Incl. S & F 240 Mm X 200 Mm X 65 Mm Ms ( 16Swg ) Switch Board And Bakelite / Perspex Top Cover Of 3Mm Thick By Brass Screws After Making Housing For Switch By Cutting Bakelite / Perspex Cover And Making Necessary Connections As Required. 95 Supply & Fixing 240 V, 1 Nos.16 A, Plug Socket&1 No. 6 A Plug Socket With Separate 1 Nos. 16 A Piano Key Type Switch & 1 No. 6 A Piano Key Type Switch ( Make Anchor Or Equivalent ) On Sheet Metal Switch Board Embedded In Wall Incl. S & F 200 Mm X 150 Mm X 65 Mm Ms ( 16Swg ) Switch Board And Bakelite / Perspex Top Cover Of 3Mm Thick By Brass Screws After Making Housing For Switch By Cutting Bakelite / Perspex Cover And Making Necessary Connections As Required. 96 Supply & Fixing 240 V, 25 A, 3 Pin Modular Type Plug Top With Indicator ( Goldmedal / Crabtree Or Equivalent ) & Necy. Connections. 97 Supply & Fixing 240 V, 25 A, Modular Type Starter ( Goldmedal / Crabtree Or Equivalent ) With 25A Modular Switch Type Dp Mcb ( Ccurve ) And 4 Module Gi Modular Type Switch Board With 4 Module Top Cover Plate Flushed In Wall Incl. S&F Switch Board And Cover Plate And Making Necy. Connections With Pvc Cu Wire And Earth Continuity Wire Etc. 98 Supply & Fixing 240 V, 20 A Plug Socket ( Make Anchor Or Equivalent ) , Without Plug Top And Switch, On Existing Sheet Metal Switch Board With Bakelite / Perspex Top Cover By Screws After Making Housing For Combined Plug Switch By Cutting Bakelite / Perspex Top Cover And Making Necy. Connections With Pvc Wire And Earth Continuity Wire Etc. 99 Supply And Delivery Of Led Street Light 6800 Lumen ( 230Vac, 60 Watt, 5500K, Ip 66, Thd<10%, Bult In 2.5Kv Spd ) With All Necessary Connection Added Extra Spd Single Die Ceramic Base High Power Led Light Source, Pdc Housing, Toughtened Glass Cover And Unique Peanut Lens To Ensure Uniform Light Distribution, Higher Spacing Between Poles And Maintenance Free System. Suitable For A1 And A2 Category Roads. Pole Dia : 48-60Mm Andsuitable For Use With 230-270 Volt 50Hz Ac Supply Etc With All Necessary Connection As Per G.S. ( Make - Philipscat No-Brp062 Led 68 Cw Slc S1 Psu / Wipro / Benlo Ultima With 5 Years Warrenty ) 100 Supply And Fixing Of Led Post Top For 360° Indirect Light Fittings Pure Polyester Uv Resistant Powder Coated Die Cast Aluminium Housing With Pmma Clear Diffuser For Uniform Illumination. And Thd<10%, Bult In 2.5Kv Spd, Ip-65 Protection ( For Gate Light ) ( Make Crompton / Philips Cat No-58175 / Wipro / Equivalent ) The Scope Of Work Also Includes The S & F Of 400 Mm Long 50Mm Dia Gi Pipe, Reducer, Nuts, Etcon Top Of The Gate Pillar After Making Hole & Mending Good The Damages With Cement Morter Mixture As Per Direction Of Eic. 101 Supply, Fabrication & Fixing Of Grill Guard Made Of Ms Round Bar / Wire ( 4 Swg ) For Gate Light Fittings To Be Fixed Over Gate Pillars In Such A Fashion That Can Be Removed For Maintenance Purpose. This Is Including Of 1 Coat Of Synthetic Enamel Paint Over 2 Coats Of Ro Primer All Complete As Per Direction Of Eic. 102 Supplying And Fixing Mcb Ss Enclosure With Ip-20 / 30Protection, Powder Coated Provision For Two / Four Pole Mcb, Concealed In Wall After Cutting The Wall & Mending Good The Damages To Original Finish Incl. Painting, Connection & Provision For Earthing Attachment ( Make As Per Approved By Eic ) ( 2Way ) 103 Fixing Only Outdoor / Street Light Type Fluorescent Light Fitting Complete With All Accessories To Be Fixed / Projected From The Wall Of The Building Incl. Making Holes To Building, S&F 40 Mm Dia Gi Pipe ( Isi-Medium ) 1.50 Mts. Average Length, With Gi Socket At One End And Thread At The Other End & Suitable Bend To House The Fitting & Making Necy. Connections With S&F Necy. Length Of 1.5 Sqmm Pvc Insulated Single Core Stranded Annealed Copper Wire And Making Connections As Required And Mending Good Damages To Wall And Painting. 104 Supplying & Fixing Gi Waterproof Type Looping Cable Box Size 200X150x100 Mm Deep Having 4 Mm Thick Comprising Of One 250V, 15A Kit-Kat Fuse Unit, One Nl On Porcelain Insulator, One Compression Type Brass Cable Gland For Upto 2- Core 16 Sqmm Pvc / A Cable And Having Lined With Rubber Gasketted Gi Top Cover With Brass Machine Screws Etc. Earthing Terminal With Lug, On Steel Tubular Pole Near Base, Including Supply & Fixing 40X6 Mm Thick, Ms Clamps With Bolts, Nuts Etc. Including Painting With Anticorrosive Paint. 105 Supply & Delivery Of 1.1 Kv Grade Xlpe / Pvc Insulated. Pvc Sheathed, Steelarmoured Al. Conductorcable Of The Following Size, And Conforming To Is: 7098 ( Part-I ) :1988 / 1554 ( Part-I ) :1988 / 5831:1984 / 3961 ( Part-I ) :1967 / 3975:1970 / 10810:1984 / 3975:1970 / 8130:1984 / 3961:1967 / 10418:1982 / 10810:1984 Asamended Upto Date, In Respect Of Component Materials And Tests, And As Per The Approved Makes List Attached Herewith ( Make- Universal / Polycab / Rr Cable / Havells / As Per Choice Of Eic ) 4 Core 10 Sq Mm 106 4 Core 16 Sq Mm 107 2 Core 10 Sq Mm 108 Laying Of Cable Upto 3 / 4 Core 25 Sqmm On Wall / Surface Incl. S & F Ms Saddles With Earthing Attachment In 10 Swg Gi ( Hot Dip ) Wire, Making Holes Etc. As Necy. Mending Good Damages And Painting. 109 Laying Of Cable Upto 2 Core 25 Sqmm On Wall / Surface Incl. S & F Ms Saddles With Earthing Attachment In 10 Swg Gi ( Hot Dip ) Wire, Making Holes Etc. As Necy. Mending Good Damages And Painting. 110 Laying Of One No. Cable Upto 35 Sqmm In Underground Trench 460 Mm Wide X 760 Mm Average Depth, With Brick Protection On The Top Of The Cable With 8 ( Eight ) Nos. Bricks Per Metre, Including Filling The Space Between The Brick & Cable And Also The Trench With Shifted Soil, Leveling Up And Restoring Surface Duly Rammed. 111 Supplying And Fixing Compression Type Gland Complete With Brass Gland, Brass Ring & Rubber Ring For Dust & Moisture-Proof Entry Of Xlpe / Pvc Armoured Cables As Below : 4 Core 10 Sqmm 112 4 Core 16 Sqmm 113 2 Core 10 Sqmm 114 Finishing The End Of Following Xlpe / Pvc Armoured Cables By Crimping Method Incl. Supplying And Fixing Solderless Socket ( Dowels Make ) , Tapes, Anticorrosive Paste & Jointing Materials. 4 Core 10 Sqmm 115 4 Core 16 Sqmm 116 2 Core10 Sqmm 117 Supplying And Fixing Double Door Horizontal Tpn Mcb Distribution Board With Ip-42 / 43 Protection, Concealed In Wall After Cutting The Wall & Mending Good The Damages To Original Finish Incl. Inter Connection With Suitable Size Of Copper Wire And Neutral Link & Provision For Earthing Attachment. 4 Way Enclosure ( Legrand / Abb / L&Tor Equivalent ) 118 Supplying And Fixing Double-Door Spn Mcb Distribution Board With Ip-42 / 43 Protection, Concealed In Wall After Cutting The Wall & Mending Good The Damages To Original Finish Incl. Inter Connection With Suitable Size Of Copper Wire And Neutral Link & Provision For Earthing Attachment. 2+10Way Enclosure ( Legrand / Abb / L&Tor Equivalent ) 119 Supplying And Fixing 240 / 415 V Mcb Isolator On Din Rail Of Existing Dbs And Necessary Connection As Per Gs. 63 A Fp ( Legrand / Abb / L&Tor Equivalent ) 120 32 A Dp ( Legrand / Abb / L&Tor Equivalent ) 121 Supplying And Fixing 240 / 415 V Mcb Of Breaking Capacity 10Ka & C Characteristics On Din Rail Of Existing Dbs And Necessary Connectionas Per Gs. 6-32 A Sp ( Legrand / Abb / L&Tor Equivalent ) 122 6-32 A Dp ( Legrand / Abb / L&Tor Equivalent ) 123 Supplying And Fixing Double Door Sheet Steel ( 16Swg ) , Powder Coated Cable End Box For Tpn Db Horizontal / Vertical Enclosure With Ip-42 / 43 Protection, On Angle Iron Frame On Wall & Mending Good The Damages To Original Finish With Nuts Bolts Etc Incl. Provision For Earthing Attachment ( Make As Per Approved By Eic ) 4Way Horizontal ( Legrand / Abb / L&Tor Equivalent ) 124 Supplying And Fixing Sheet Steel ( 16Swg ) Cable End Box On Tpn Sfu Enclosure With Nuts Bolts Etc Incl. Powder Coated Painting. 63 / 125 A ( ( Legrand / Abb / L&T ) 125 Supplying And Fixing 415V, Tpn Sfu With Sheet Steel Enclosure On Angle Iron Frame On Wall With Nuts Bolts Etc Incl. S & F 3 Nos. Din Type Hrc Fuse As Per Rating 63A ( L&T / Havells ) 126 Supply And Delivery Of Twin Led Tube Fitting ( 2 X 20Watt, 230Vac, 50Hz, 4000K Nw, Thd<10%, Bult In 2.5Kv Spd ) With All Accessories And 2 Nos Led Tube [ Make: Philips, Bajaj, Wipro, Jaquar With 3 Year Warrenty ] . 127 Supply And Delivery Of Single Led Tube Fitting ( 20Watt, 230Vac, 50Hz, 4000K Nw, Thd<10%, Bult In 2.5Kv Spd ) With All Accessories And 1 Nos Led Tube [ Make: Philips, Bajaj, Wipro, Jaquar With 3 Year Warrenty ] . 128 Supply And Fixing 240Volt 9 Watt 825 Lumen B 22 Base Non-Dismmable Led Lamp On Wooden Circular Board [ Make: Philips, Bajaj, Wipro, Jaquar With 3 Year Warrenty ] . 129 Fixing Only Single / Twin Fluorescent Light Fitting Suspended 25 Cm Bellow The Ceiling With 2 No. 20 Mm Dia Ei Conduit ( 14 Swg ) Supports Fixed With “L” Type Ms Clamp Whose One Side Fixed On Ceiling With Sutable Size 4 Nos. Fastener And Other Side Connected With The Conduit With Suitable Size Of Bolts And Nuts Incl. S&F Ei Conduit, “L” Type ( 125Mmx125mm ) 6Mm Thick And 25Mm With Ms Clamps And Connecting The Length Of Pvc Insulated Wire And Mending Good Damages To Original Finish And Painting Etc. By 2X24 / 0.20 Mm ( 1.5Sqmm. ) Flexible Copper Wire Of 1.10 Mt. Length. 130 Fixing Only Single / Twin Florescent Light Fitting Complete With All Accessories Directly On Wall / Ceiling With Hw Block And Suitable Size Ms Fastener, Ceiling Plate, Nipples Etc. As Required. 131 Supply Of 3 Star Rated 48 ( 1200Mm Dia ) Ceiling Fans Complete With All Accessories ( Make - Crompton, Hs Plus / Orient, Summer King / Usha, Striker ) . 132 Supply& Delivery Of 36 ( 900 Mm ) & 240 V Ac Ceiling Fan With Including All Accessories ( Blades, Canopy, Fork, Rubber Bush, Capacitor Type:P2 As Per Eic ) [ Make-Orient / Crompton / Usha Striker With Safety Wire / Epc Or Brand Approved By Eic ] 133 Engraving The Deptt. Number With 10 Mm Lettering On The Body Of Fan Upto 10 Letters Incl. Hifen, Stroke Or Stop. 134 Fixing Only Ceiling Fan Complete With Blades, Canopy, Fork, Rubber Bush Etc. Incl. S&F Connecting Wire For Down Rod Upto 30 Cm Incl. Painting The Rod With Approved Paint And Making Necessary Connection As Required By 2X1.5 Sqmm Flexible Copper Wire. 135 Painting Upto 10 Letters Of The Engraved Number With Approved Black / Red Paint As Required. 136 Supplying & Fixing Of Box Type Fan Clamp Of 150Mm Dia & 80Mm Depth Made Of 16 Swg Crca Sheet With One End Duly Sealed By Cover, Properly Welded, Incl. S&F 12Mm Dia 600Mm Long Ms Rod Duly Bent By Heat Treatment At The Centre Position Of Rod To Grip Fan Bobbin Properly, Incl. Binding The Rod And Fan Box With Reinforcement By 22 Swg Steel Binding Wire, Incl. Supplying & Covering The Box With Alkathene Sheet, Placed In Order To Prevent Concrete From Entering The Box. 137 Supply & Fixing Socket Type Fan Regulator ( Step Type ) ( Make Anchor ) On Existing Sheet Metal Switch Board With Bakelite / Perspex Top Cover By Screw After Making Housing For Regulator Knob By Cutting Bakelite / Perspex Top Cover Incl. Making Necy. Connections Etc. 138 Supply And Delivery Of 230V 50 Hz, ( 9 ) / 230 Mm, 1370 R.P.M With All Necessary Accessories Like Wire Guard Etc. , Min 2 Years Warranty Certificate, Test Certificate Etc. [ Make: Epc, Usha, Cg, Bajaj ] 139 Fixing Only Exhaust Fan After Making Hole In Wall And Making Good Damages And Smooth Cement Finish Etc. As Practicable As Possible And Providing Necy. Length Of Pvc Insulated Wire And Making Connection For Exhaust For 30 Cm ( 12 ) 140 Supply & Fixing Louver Shutter On Wall With Necy. Bolts & Nuts ( 6 Mm Dia X 62 Mm Long ) For Al 30 Cm Exhaust Fan ( 12 ) 141 Earthing With 50 Mm Dia Gi Pipe 3.64 Mm Thick X 3.04 Mts. Long And 1 X 4 Swg Gi ( Hot Dip ) Wire ( 4 Mts. Long ) , 13 Mm Dia X 80 Mm Long Gi Bolts, Double Nuts, Double Washers Incl. S & F 15 Mm Dia Gi Pipe Protection ( 1 Mts. Long ) To Be Filled With Bitumen Partly Under The Ground Level And Partly Above Ground Level Driven To An Average Depth Of 3.65 Mts. Below The Ground Level As Below By Tata-Medium Gi Pipe 142 Extra For Providing Masonery Enclosure On The Top Of The Earth Electrode Of Overall Size 86.36 Cm X 86.36 Cm X 46 Cm Deep ( Below Ground Level ) Complete With Cemented Brick Work ( 1:6 ) Of 25 Cm Width Duly Plastered With Cement Morter ( Inside ) Ci Hinged Inspection Cover Of Size 36.56 Cm X 35.56 Cm With Locking Arrangement, Gi Reducer Including Drilling Of 46 Nos.12 Mm Dia Holes On The Gi Pipe 143 Excavation Of Soil For Installation Of Earth Electrode And Filling & Ramming ( For Morrum Soil ) As Per Gs. 144 Supplying & Fixing Earth Busbar Of Galvanized ( Hot Dip ) Ms Flat 25 Mm X 6 Mm On Wall Having Clearance Of 6 Mm From Wall Including Providing Drilled Holes On The Busbar Complete With Gi Bolts, Nuts, Washers, Spacing Insulators Etc As Required. 145 Connecting The Equipments To Earth Busbar Including S & F Gi ( Hot Dip ) Wire Of Size As Below On Wall / Floor With Staples Buried Inside Wall / Floor As Required And Making Connection To Equipments With Bolts, Nuts, Washers, Cable Lugs Etc. As Required And Mending Good Damages. Solid Gi Wireno. 4 Swg
