Providing And Fixing Of Cubical Lt Panel At An Block Pitampura Area - Supply / Fabrication Of L T Panel Board Cubical Type, Floor Mounting, Dust & Vermin Preventing Construction, Of The Minimum Size 1500 X 1500 X 300 Mm, Suitable For Indoor Fixing, Made Out Of 16 Swg Crca Sheet ( Frame Of 14 Swg ) , With Provisions For Cable Entry From Bottom And Having Chambers As- Two Incomer Chambers ( One Each For The Changeover And Incomer Mccb ) , One Metering Chamber For The Main Incomer Mccb, Two Outgoing Chambers For The Star Delta Starters For 25 Hp Motors, , One Outgoing Chamber For Two Nos. Of Lighting Mcbs. The Panel Should Have Separate Cable Alleys And Bus Bar Alleys. It Should Be Suitable For Operation And Maintenance From The Front And Having Removable Covers At The Back And Having Doors Complete With Locks Etc. At The Front For Each Chamber. The Rating Of Main Bus Bars Has To Be 200 Ampere For Three Phases And Half For The Neutral In Aluminium Construction Duly Sleeved With Phase Indicating Heat Shrinkable Sleeves. It Should Be Complete In All Respect Along With Painted Through Powder Coating Process And With Complete Provisions Suitable For All The Switchgears As Below To Be Fitted / Installed Properly So As To Make Two Incomers, One Main Metering Module, One For Lighting Supply, Two Star Delta Starters With Complete Mounting Accessories As Per Requirement With Complete Internal Connections Of Switchgears And Control Gears With The Main Bus Bars In The Panel Through Copper Cable Orbus Bars Along With Making All The Required Wiring Connections For All Measuring And Indicating Instruments With All The Accessories, Thimbles, Ferrules Etc. Complete In All Respect As Per Requirement. 2 S / O Changeover, Switch, 200 Amp, 4 Pole, 415V Ac.Make:-L&T / Schneider / Hpl 3 S / O Moulded Case Circuit Breaker ( Mccb ) Of Rating 200 Amp, Triple Pole, 415V, Ac Of Breaking Capacity Of 36 Ka Or More. Make:-L&T / Schneider / Bch / C&S 4 S / O Moulded Case Circuit Breaker ( Mccb ) Of Rating 100 Amp, Triple Pole, 415V, Ac Of Breaking Capacity Of 50 Ka Or More. Make:-L&T / Schneider / Bch / C&S 5 S / O Moulded Case Circuit Breaker ( Mccb ) Of Rating 63 Amp, Triple Pole, 415 V, Ac Of Breaking Capacity Of 36 Ka Or More. Make:-L&T / Schneider / Bch / C&S 6 S / O Power Contactor, 70 A, Tp, 220V / 415V Ac Make:-L&T / Schneider / Bch / C&S 7 S / O Power Contactor, 18 A, Tp, 220V / 415V Ac Make:-L&T / Schneider / Bch / C&S 8 S / O Power Contactor, 50 A, Tp, 220V / 415V Ac Make:-L&T / Schneider / Bch / C&S 9 S / O Motor Protection Relay Mpr 300 32-88 Amp Make:-L&T / Schneider / Bch / C&S 10 S / O Timer For Starter Make:-L&T / Schneider / Bch / C&S 11 S / Oadd On Block 1 No + 1 Nc Make:-L&T / Schneider / Bch / C&S 12 S / O Overload Relay For 20 Hp, 30 – 50 Amp Mn 5 Make:-L&T / Schneider / Bch / C&S 13 S / O Overload Relay For 9-15 Amp Mn 5 Make:-L&T / Schneider / Bch / C&S 14 S / O Single Phase Preventermake:-L&T / Schneider / Bch / C&S 15 S / Opush Buttons With Contact Block Make:-L&T / Schneider / Bch / C&S 16 S / O Ampere Meter Digital Type.Make:-L&T / Schneider / Ae 17 S / O Volt Meter Digital Type. Make:-L&T / Schneider / Ae 18 S / O Ampere Meter Selector Switch. Make:-L&T / Schneider / Bch / C&S 19 S / O Volt Meter Selector Switch. Make:-L&T / Schneider / Bch / C&S 20 S / O Indicating Lamp, Led Type Make:-L&T / Schneider / Bch / C&S 21 S / O Mcb, 6 Amps, Sp, ‘C’ Curve. Make:-L&T / Schneider / Bch / C&S 22 S / O Mcb, 63 Amps, Fp, ‘C’ Curve. Make:-L&T / Schneider / Bch / C&S 23 S / O Mcb, 32 Amps, Tp, ‘C’ Curve. Make:-L&T / Schneider / Bch / C&S 24 S / O Current Transformer 100 / 5 Ampere. Make:-Ae / Kuppa / Matrix 25 S / O Current Transformer 200 / 5 Ampere. Make:-Ae / Kuppa / Matrix 26 Making Complete Connections Of The Above Switchgears With The Main Bus Bars In The Panel Through Copper Cable Or Aluminium Bus Bars And Also Making Their Interconnections With Each Other As Per Requirement Including Making Provisions For Jointing The Outgoing / Incoming Cables. 27 Making All The Required Wiring Connections For All The Metering Chambers / Outgoing Chambers Of The Panel For All Measuring And Indicating Instruments As Above And For Dol Starter Chamber For Starter Operation Through Copper Cable With All The Accessories, Thimbles, Ferrules Etc. Complete In All Respect As Per Requirement. 28 Dismantling Of Old Panel Board And Disconnecting All The Old Incoming And The Outgoing Connection And Shifting The Panel From The Site. 29 Fabrication And Supply Of Base Frame Made Out Of Angle Iron Of Suitable Size For Fixing The Above Panel And Suitable For Making Outgoing / Incoming Cable Entries In The Panel. It Should Be Duly Painted And Ready With Provisions For Installing At The Site. 30 Fixing Of New Base Frame At The Site With The Help Of Fasteners / Welding And Grouting Of Nut Bolts And Including All Other Work As Per Site Requirements And Fixing The New L T Panel At The Newly Fixed Base Frame By Lifting The Panel Board And Placing It At The Base Frame Properly And Fixing It To The Frame By Nut Bolts As Requirement. 31 Dismantling The Existing Kit Kat Fuse Board After Disconnecting The Cable Connections. Supply And Fixing Of Kit Kat Board Suitable For Fixing The Kit Kat Board. Also Providing The New Kit Kat For The Newly Frame. The Job Includes Providing And Fixing Of Nut / Bolts / Fasteners Etc. For The Job As Required. 32 Making The Connection From The Metering To The Kit Kat After Relaying Of Existing Cable And, Proper Thimbling And Tapping / Making End Terminations Etc. Including Providing & Fixing Of All The Material As Required. 33 Making The Incoming Connections To The New Panel By Single Core Copper Cable Having 25 Sqmm Size From Kit Kat Board And Tapping / Making End Terminations Etc. Including Providing & Fixing Of All The Material As Required. 34 Making The Outgoing Connections By Connecting Out Going Mccbs Of The Panel To Their Respective Starters Etc. Through Existingcables After Re-Laying Of Cables As Per Site Requirement And After Proper Thimbling And Tapping / Making End Terminations Etc. Including Providing & Fixing Of All The Material As Required. 35 Making The Outgoing Connections By Connecting Dol Starter To The Motor Through Existing Cable After Re-Laying Of Cable As Per Site Requirement And After Proper Thimbling And Tapping Etc / Making End Terminations Including Providing & Fixing Of Material As Required. 36 Testing And Commissioning Of The Panel Board First At No Load And Then At On Load And For Operations / Tripping As Per The Satisfaction Of Engineer In Charge.
