Bids Are Invited For FIRE EXTINGUISHER-CO2 TYPE , PUNCH CENTRE 120 MM X 10 MM DIA.--KNURLED BODY , HAMMER BALL PEIN 220 GRAMS - 250 GRAMS - 0.5 LB WITH HANDLE , SAFETY GOGGLES- GLASS PLASTIC OR FIBER , PUNCH DOT SLOT . DIA 10 X 100 MM , STRAIGHT EDGE ENGINEER S 300 X 50 X 12 MM BEVELLED EDGE. , LEVEL SPIRIT 300 MM , EXTRACTORS -SCREW-STUD SIZES 1 TO 8 -SET , MICROMETER IN SDIE 25 MM TO 50 MM LEAST COUNT 0.01 MM WITH EXTENSION RODS UP TO 150 MM , VERNIER CALIPER SET 150 INSIDE AND OUTSIDE ,DEPTH TO READ INCHES AND MM , SCREW PITCH GAUGE FOR METRIC PITCHES 0.25-6 MM , GAUGE -WIRE,METRIC STANDARD. , UNIVERSAL SCRIBING BLOCK 220-225-250 MM. PILLAR. , BLOCKS VEE 150 X 100 X 100 MM.WITH CLAMP , ANGLE PLATE ADJUSTABLE 150X150X250 MM , DRILLING MACHINE ELECTRIC PORTABLE 12 MM CAPACITY , DRILL TWIST ST. SHANK METRIC 3 MM TO 12 MM , IN STEP OF 0.5 MM. , DRILL TWIST TAPER SHANK 8 MM TO 20 MM BY 0.5 MM , TAPS AND DIES COMPLATE SET IN BOX .B.S.W. , TAPS AND DIES COMPLETE SET 5, 6, 8, 10 and 12 MM SET OF 5 , FILE FEATHER EDGE SMOOTH.150 MM , FEELER GAUGE 0.05 MM TO 0.3 MM BY 0.05 AND 0.4 MM TO 1MM BY 0.1 MM 13 LEAVES , FILE FLAT 2ND CUT 300 MM SAFE EDGE , CARD FILE STEEL WIRE BRUSH 3in. X 5in. , PLIER COMBINATION 150 MM INSULATED , BLOW LAMP 0.5 LITER , SPANNER DOUBLE ENDED 6 TO 22 MM SET OF 8 , SPANNER-WRENCH ADJUSTABLE 150 MM , INTERCHANGEABLE RATCHET SOCKET SET WITH A 12 MM DRIVER SIZE 10 TO 32 MM SET OF 18 SOCKET AND ATTACHMENT , BOX SPANNER SET 6-25 MM SET OF 10 PCS WITH TOMMY BAR DIA 6,8 ,10,12,14, 16 , GLASS MAGNIFYING 75 MM DIA , CLAMP-VICE TOOL MAKER 5 CM AND 7.5CM SET OF 2. , REAMER MACHINE 12 MM TO 16 MM IN STEPS OF 0.5 MM-SET , SCRAPER FLAT 12 MM X 150 MM. , SCRAPER 3 CORNER 15 CM. , SCRAPER HALF ROUND 15 CM. , CHISEL COLD CROSS CUT 9 MM X 150 MM , CHISEL DIAMOND POINT 9 X 150 MM , CHISEL COLD FLAT 9 MM X 100 MM , CHISEL COLD 9 MM ROUND NOZE 100 MM , VICE PIPE 4in. JAW -10CM. , MORSE TAPER SLEEVES NO. 0TO1, 1TO2,2TO3,3TO4,4TO5, , FIRE BUCKET- SAND BUCKET , VICE MACHINES 100 MM , TORQUE WRENCH 12- BUCKET , VICE MACHINES 100 MM , TORQUE WRENCH 12- 68NM. , POWER TOOL FOR FASTENING CAPACITY 10 TO 18MM , PROFILE GAUGES PLATE TYPE FOR DEMONSTRATION METRIC STANDARD , MACHINE MAINTENANCE MANNUAL FOR LATHE, PEDESTAL GRINDER, DRILL MACHINE, POWER SAW , TEMPERATURE GAUGE RANGE 0 - 150C , DOWEL PIN STRAIGHT DIA. -1in. LENGTH -4in. MAT- STAINLESS STEEL , STANDARD TAP SCREWS M3, M4, M5, M6, M8, M10, M12, M14, M16 , LAPPING PLATE 6in. DIA , MEDIUM CARBON HEAT TREATED ALLOY STEEL METRIC STUDS AND BOLTS ALONG WITH NUTS FOR DISPLAY OF STANDARD LENGTH MAY BE MANUFACTURED IN-HOUSE M6, M8, M10, M12, M14, M16 STANDARD , CAPS SCREWS M6, M8, M10, M12 , DRILLS GUAGE STRAIGHT SHANK LETTER SIZES A TO Z WITH GUAGE , DRILLS GUAGE STRAIGHT SHANK WIRE SIZE 1 TO 60 WITH GUAGE , DRILL GAUGE 1,5 TO 12.5 MM IN STEPS OF 0,5 MM , GLOBE VALVE CAST IRON FLANGED TYPE 150NB, CLASSNO 150 FLANGE-ANSI125-B16.1 , GATE VALVE DIA FLANGED TYPE 150NB, CLASSNO 150 FLANGEANSI125- B16.1 , STOP COCK 25NB 2-WAY, THREADED END , PIPE MILD STEEL MS 150NB, SCH.40, ERW, IS-1239 , PIPE GALVENIZED IRON GI 25MM, SCH.40, ERW , FLANGE SLIPON FORGED STEEL FLANGE 150NB, ANSI-B16.5, CLASSNO150 , BOLT NUT AND WASHER SET M20X2.5X90LONG PART THREAD - HEX. HEAD , DIE and DIE STOCK COMPLETE BSP in. , DIE and DIE STOCK COMPLETE BSP 3-4in. , DIE and DIE STOCK COMPLETE BSP 1in. , JIGS and FIXTURE SAMPLE -FOR DEMONSTRATION , KEY TO FIT SHAFT AND PULLEY , GEAR - SPUR OLD DAMAGED TO FIT 50 MM SHAFT DIA , BELT in.Vin. TO FIT ON PULLEY , BELT in.FLATin. TO FIT ON PULLEY , GASKET- PACKING PTFE ROLL , WASHER, CLUTCH, KEYS, JIB, COTTER and CIRCLIP MINIMUM 25MM SIZE, CARBON STEEL MATERIAL , PUNCH HOLLOW 5 TO 12 MM DIA. , DRIFT DRILL 200 MM HARDENED AND BLACK FINISH , BEARING DIFFERENT TYPES EACH TYPE OF DIAMETER 25MM MIN. , LIFTING SLING 8MM NOMINAL DIA. SINGLE LEG SLING , PULLER SET UNIVERSAL BEARING AND BUSHES , PULLER FOR PULLY , POKER - 900 MM LONG , PUNCH PRICK 100 MM. , MALLET. DIA 100 MM X 150 MM , SNIP STRAIGHT 300MM , HAMMER FLAT HEAD WITH HANDLE , HAMMER PLANISHING WITH HANDLE , SNIP BENT 250 MM , STAKE HATCHET WITH LEG. 300 X 200 X 20 MM , STAKE GROOVING. 100 X 100 X 300 MM , GAUGE - SNAP GO AND NO GO 25 TO 50 MM BY 5 MM. , GAUGE PLUG SINGLE ENDED 5 TO 55 BY 1 MM. , TELESCOPIC GAUGE RANGE 8-150 MM SET OF 6 PCS , DIAL TEST INDICATOR 0.01 MM ON STAND.L.C. , SINE BAR 125 MM. , DIAL VERNIER CALIPER. UNIVERSAL TYPE 0 - 300 MM, LC 0.05 MM , SCREW THREAD MICROMETER WITH INTERCHANGEABLE. PITCH ANVILS FOR CHECKING METRIC THREADS 60. 0 - 25 MM LC 0.01 MM , DEPTH MICROMETER. 0-25 MM ACCURACY 0.01 MM WITH STANDARD SET OF EXTENSION RODS UPTO 200 MM , DIGITAL VERNIER CALIPER 150 MM, LEAST COUNT 0.02 MM , MICROMETER -DIGIMETRIC ELECTRONIC OUTSIDE 1 TO 25 MM 0.001MM L.C. , COMPARATOR STAND WITH DIAL INDICATOR.L.C.-0.0.01MM , SURFACE ROUGHNESS COMPARISON PLATES N1-N12 GRADES , VERNIER CALIPERELECTRONIC- DIGITAL INCH and MM. 8in.-200 MM. LCM 01.0005in.-0.01 MM , CARBIDE WEAR BLOCK 1 MM-2 MM. , TOOLS BITS HSS 10 MM SQUARE , LATHE TOOLS BIT 6 MM X 75 MM. , LATHE TOOLS BIT 8 MM X 75 MM. , TOOL BIT HOLDER AS ARMSTRONG R.H. , TOOL BIT HOLDER AS ARMSTRONG L.H. , TOOL BIT HOLDER AS ARMSTRONG STRAIGHT. , PIPE WRENCHES 250MM LONG , CUTTER, PIPE WHEEL TYPE 6 MM TO 25 MM. , PIPE BENDER SPOOL TYPE WITH STAND MANUALLY OPERATED. UP TO 25MM WITH STAND MANUALLY OPERATED. UP TO 25MM , ADJUSTABLE PIPE CHAIN TONGE TO TAKE PIPES UP TO 300 MM. , SPANNER-WRENCH ADJUSTABLE 375 - 380 MM IS - 1649. Total Quantity : 369
