}

Tender For Rectification Of Defects Of Md Accn Wk At Fatehgarh, fatehgarh-Uttar Pradesh

Statutory Bodies & Commissions/Committees has published Tender For Rectification Of Defects Of Md Accn Wk At Fatehgarh. Submission Date for this Tender is 07-01-2023. Brooms and Mops Tenders in fatehgarh Uttar Pradesh. Bidders can get complete Tender details and download the document.




Tender Notice

35223081
Corrigendum : Tender For Rectification Of Defects Of Md Accn Wk At Fatehgarh
Open Tender
Indian
Uttar Pradesh
Fatehgarh
07-01-2023

Tender Details

Tender For Rectification Of Defects Of Md Accn Wk At Fatehgarh - Demolition Of Cement Concrete ( Unreinfored ) In Ground Floors And Pavings N. Exc. 15 Cm Thickness ( Below Or Above Ground Level ) Complete All As Specified And Directed. 2 Taking Down Cement Plaster On Brick Or Stone Walls, Etc Including Raking Out Joints, Hacking For Key, Scrubbing Down With Water Etc Complete All As Specified And Directed. 3 M&L For 15 Mm Thick Cement Plastering In Cm 1:6 On Brick Or Concrete Surfaces Fair Finished The Surfaces Even And Smooth Without Using Extra Cement Complete All As Specified And Directed. 4 M&L For Preparation Of Newly Plastered Surfaces Of Wall And Applying Two Coats Of Oil Bound Distemper Over A Coat Of Primer Complete All As Specified And Directed. 5 Dismantling Of Floor Hearth Or Wall Tiling Any Type Including Cement Mortar Bedding Complete All As Specified And Directed. 6 S&F Non Skid Coloured Ceramic Tiles 7 To 8 Mm Thick ( Square / Rectangular ) Area Of Each Tile Exceeding 0.06 Sqm But Not Exceeding 0.11 Sqm In Floors And Skirting Etc Set And Jointed In Neat Cement Slurry And Pointed In White Or Coloured Cement To Match Including 15 Mm Screed Bed In Cm 1:6 Complete All As Specified And Directed. 7 S&F Non Skid Coloured Ceramic Tiles 7 To 8 Mm Thick ( Square / Rectangular ) Area Of Each Tile Exceeding 0.11 Sqm But Not Exceeding 0.18 Sqm In Floors And Skirting Etc Set And Jointed In Neat Cement Slurry And Pointed In White Or Coloured Cement To Match Including 15 Mm Screed Bed In C:M 1:6 Complete All As Specified And Directed. 8 S&F In Repair 15 Mm Bore Chromium Plated Bib Taps Fancy Type, Cast Copper Alloy With Crutch Or Butterfly Handle, Screwed Down, Screwed For Iron Pipe Or For Brass Ferrule And Fixed Complete All As Specified And Directed. 9 S&F In Repair 4 Mm Dia Cloth Handing Gi Wire Fixing With Iron Angle Complete All As Specified And Directed. 10 M&L For 15 Mm Dia Cp Mixer In Repairfor Mixing Of Hot & Cold Water Screwed Down For Iron Pipe Complete All As Specified And Directed. 11 Taking Down And Refixing In Same Opening Of Particle Board Drawer And Shutter Of Any Complete All As Specified And Directed. 12 S&F In Repair 18 / 19 Mm Thick Prelaminated Particle Board, Interior Grade, Prelaminated One Side With Decorative Choice Lamination & Other Side Balancing White Lamination, Provided For Making Cabinet Drawer & Shutter Suitable Fixed With Wooden Frame Complete All As Specified And Directed. 13 M&L For Providing And Fixing Steel Roller For Wooden Drawer With Necessary Screwes Etc Complete All As Specified And Directed. 14 Supply & Fixed In Repairs 40 Mm Dia Brass Knobs Complete All As Specified And Directed. 15 Taking Down Shutter Of Any Description Exc. 1.00 Sqm But N. Exc. 2.00 Sqm Complete All As Specified And Directed. 16 S&F 30 Mm Flush Shutters, Solid Core Construction, With Block Board Core And Plywood Face Panels, Commercial Type On Both Sides Complete All As Specified And Directed. 17 S&F Aluminium Anodized Barel Tower Bolt Of Extruded Section 150 Mm Long Complete All As Specified And Directed. 18 S&F Aluminium Alloy Handle Cast Type Anodized Of Size 150 Mm Long Complete All As Specified And Directed. 19 S&F Butt Hinges Medium Weight Cold Rolled Mild Steel 100 Mm Size Complete All As Specified And Directed. 20 S&F 250 Mm Long Aluminium Alloy, Anodized, Sliding Door Botl With Hasp, Staple ( Bolt Type ) And Fixing Clips Of Sheet, Cast Or Extruded Sections And Fixing Bolts And Sliding Bolts Of Extruded Sections Or Cast Aluminium Alloy And Fixed Complete All As Specified And Directed. 21 M&L For Preparation Of New Or Previously Untreated Surfaces Of Wood And Wood Based Surfaces Of Any Description, Over 10 Cm In Width Girth And Apply Two Coats Of Synthetic Enamel Paint Over A Coat Of Woode Primer Complete All As Specified And Directed. 22 Hacking Out Old Broken Glass ( Any Thickness, Size, Quality Or Description ) From Wooden / Steel Frame Glazed With Putty Of Fixed With Beads Complete All As Specified And Directed. 23 S&F In Repair For Pvc Low Level Flushing Cistern 10 Ltr Capacity With Cyphonic, Action Pvc Float Valve, Brackets And 32 Mm Bore Pvc Flush Pipe Etc Including Pvc Connection 450 Mm Long As Specified Andfixed In Repair Complete All As Specified And Directed. 24 Supply And Fixed In Repair Magic Eye Suitable To Flush Door Shutter ( 35 Mm Thick ) Complete All As Specified And Directed. 25 Supply In Repair Towel Ring Of Ptmt Fixed With And Including Chromium Plated Brass Screws Land Wooden / Plastic Cleats ( Minimum Weight 90 Gms ) Complete All As Specified And Directed. 26 Taking Down Shutter Of Any Description N. Exc. 1.00 Sqm Complete All As Specified And Directed. 27 S&F Anodized Aluminium Window And Ventilator Shutters, Side Hung Type Without Sash Bars, Aluminium Sections Weighing 0.55 Kg / M Including Necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodized Aluminium Snap Beading, Screws, Anodized Aluminium Fittings Such As Peg Stays 150 Mm Long ( 1 No. ) Hinges Type B-21 100 Mm Long ( 2 No. ) Suitable Handle ( 1 No. ) With Necessary Roller And Hinges Complete All As Specified And Directed. 28 M&L For 4 Mm Thick Sheet Glass, Ordinary Quality, In Squares N. Exc. 0.5 Sqm Each Pane, Complete All As Specified And Directed. 29 Fixing Only Iron Greel ( Size 1.2 X 1.2 M ) Fixed With Wall With Necessary Concrete Work. Complete All As Specified And Directed 30 Supply And Fixed In Repair Of Cast Iron Work Grade Fg 150, Gully Traps Size 300 X 300 X 8 Mm, Weight Etc 5 Kg Each Complete All As Specified And Directed. 31 M&L For Forming 12 Mm Thick 100 Mm Depth Expansion Joint Filled With Preformed Bitumenious Filler And Sealed With Sealing Compound Grade A Complete All As Specified And Directed. 32 M&L For Machine Cut Kota Stone Flooring 20-25 Mm Thick Over 15 Mm Screed In Cement Mortar 1:6 And Jointed With Grey Cement Slurry Mixed With Pigment For Match The Shade Of The Slab Including Rubbing And Polishing Complete All As Specified And Directed. 33 M&L For Washed Stone Grit Plaster On Exterior Walls In Two Layers, Under Layer 12 Mm Cement Plaster 1:4 ( 1 Cement : 4 Coarse Sand ) Furrowing The Under Layer With Scratching Tool, Applying Cement Slurry On The Under Layer @ 3 Kg Of Cement Per Square Metre, Top Layer 15 Mm Cement Plaster 1:1 / 2:2 ( 1 Cement : 1 / 2 Coarse Sand : 2 Stone Chipping 10 Mm Nominal Size ) In Panels With Groove All Around As Per Approved Pattern Including Scrubbing And Washing, The Top Layer With Brushes And Water To Expose The Stone Chippings Complete All As Specified ( Payment For Providing Grooves Shall Be Made Separately ) Complete All As Specified And Directed. 34 M&L For Forming Groove Of Uniform Size 15 Mm Wipe And 15 Mm Deep In The Top Layer Of Washed Stone Grit Plaster As Per Approved Pattern Using Looden Batterns, Nailed To The Under Layer Including Removal Of Wooden Battens, Repair To The Edges Of Panels And Finishing The Groove Complete All As Specified And Directed. 35 M&L For 75 Mm Thick Pcc ( 1:3:6 ) Type C-2 ( 40 Mm Graded Stone Aggregate ) As In Foundations, Filling And Mass Concrete Complete All As Specified And Directed. 36 Supply & Fixed In Repair 200 Mm Mild Steel Tee Hinges, Enamelled Black, Heavy Type Including Welding In Repair N. Exc. 2.5 Cm In Length Complete All As Specified And Directed. 37 S&F Cp Brass Heath Faucet With Flexible Pipe 1.00 M Tube And Hook Fixed For Ewc Suitable For 15 Mm Bore Of Pipe Etc Complete All As Specified And Directed. 38 S&F Joist, Channel, Angle Or Tee Sections Fixed Independently Without Connecting Plates Etc Fixing With Railing Properly In Wall As Complete All As Specified And Directed. 39 S&F 0.56 Mm Thick Plain Alumium Sheeting Alloy 31000 H 4 In Straight Flashing ( Length And Girth As Fixed ) Complete All As Specified And Directed. 40 Demolition Of Brick Work Or Stone / Boulder Masonry Built In Cement Mortar Including All Quoins, Arches, Pillars Etc Complete All As Specified And Directed. 41 M&L Brick Work Using Old Size Sub Class B Brick Straight Or Curved On Plan Exc 6 M Mean Radius Built In Cement Mortar 1:6 Complete All As Specified And Directed. 42 M&L 15 Mm Thick Cement Plastering In Cm 1:4 On Brick Or Concrete Surfaces Fair Finished The Surfaces Even And Smooth Witout Using Extra Cement All As Specified And Directed. 43 M&L For Two Coats Of Cement Based Paint Over A Coat Of Alkali Resistant Primer On New Plastered Wall Surfaces Including Preparation Complete All As Specified And Directed. 44 M&L For Grinding And Wax Polishing Of Kota Stone Flooring Complete All As Specified And Directed. 45 M&L For Preparing Existing Black Top Surfaces By Brushing With Wire Brushes For Removing Caked Mud Etc, Sweeping With Brooms And Finally Fanning The Cleaned Surfaces With Gunny Bags To Remove All Loose Dirt Etccomplete All As Specified And Directed 46 M&L For Applying Evenly A Tack Coat With Bituminous Primer ( Paving Bitumen Vg-10 ) @ 5 Kg Per 10 Sqm Over The Prepared Surfaces By Mechanical Sprayer Complete All As Specified And Directed. 47 M&L For Laying Bituminous Premix Asphaltic Semi Dense Concrete 25 Mm Consolidated Thickness With 6% Binder Content Byweight Of Total Mix, ( Paving Bitumen Vg-30 ) Rolled And Compacted With 8 To 10 Tonnes Power Road Roller To Required Camber And Gradient Complete All As Specified And Directed.Note :- ( A ) Premix Concrete Shall Be Mixed In Hot Mix Plant, Transported From Plant To Work Site And Laid / Spread By Means Of Mechanical Paver. ( B ) Contractor Shall Quote His Rate On This Basis Of Binder As Mentioned In Above Item If There Is Any Variation In The Actual Binder Content Used, The Rate Shall Be Adjusted Lower Side Of Binder Used. However No Price Adjustment Shall Be Made If The Binder Content Works Out To More Than As Specified In Sch A 48 Supply & Fixing By Sodium Vapour Lamp Type 70W Post Top Lantern Type Wipro Cat. Ref, No-Wps 27A71 Or Equivalent, Complete With Control Gear Cover Etc With Lamp 70W Hpsv, Connection Pvc Cable Of Size 3 X 2.5 Sqmm Copper Conductor With 3 Mtrs Long And 50 Mm Dia Gi Pipe As Support Complete All As Specified Anddirected. 49 Supply, Fixing, Testing & Commissioning Of Outdoor Stand Mounted Feeder Pillar With Ip65 Protection, Factory Made Fabricated Made Out Of 2.1Mm Thick Crca Sheet Steel Door Fixed With Hinges And Complete With McbS At Incoming & Outgoings ( Nos. Of Incoming & Outgoing McbS Mentioned Below ) , 100A, 25Ka, Tpn Aluminium Busbar, Single Dial Time Switch, 45A Tp Contactor For The Automatic Switching Of Luminaries, Power Tool Control With 2 Nos 9A Contactors And Raise Lower Push Button, Incoming 35 Sq. Mm ( 3.5C / 4C ) And Outgoing 16 & 25Sq. Mm Terminals. Feeder Pillar Should Be Having Following Accessories & As Directed By Engr In Charge And With Use Of Timer Controls ( In The Feeder Pillars ) With Control To Reduce The Lighting Be Created As:- ( I ) 6 Pm To 10 Pm-100% ( Ii ) 10 Pm To 02 Am-66% ( Iii ) 2 Am To 6 Am-33% ( Setting Of Timer As Per This Is Contractor Responsibility ) Note:Complete All Earth Work Excavation & Cement Concrete For Foundationembedded In Pcc 1:3:6 Type C-2 ( Using 40 Mm Graded Stone Aggregate ) N. Exc. 0.45 Cumand Provision Of Following Accessories Complete All As Specified And As Directed.Incomera ) 63A Tpn Mcb, 25Ka-1 Nob ) Ct For Meter 63 / 5A 10Va, Cl-1 Accuracy - 3Nosc ) Analoque Type Volt & Ampere Meterd ) One Set Phase Indication Lamp Led Type With 3Nos, 6A, 220V Sp Mcboutgoinge ) 16A Tpn Mcb, 10Ka-4 Nos. 50 All As Item No. 49 Above But Having Following Accessories:Incomera ) 63A Tpn Mcb, 25Ka-1 Nob ) Ct For Meter 63 / 5A 10Va, Cl-1 Accuracy - 3Nosc ) Analoque Type Volt & Ampere Meterd ) One Set Phase Indication Lamp Led Type With 3Nos, 6A, 220V Sp Mcboutgoinge ) 16A Tpn Mcb, 10Ka-3 Nos. 51 Supply, Fixing, Testing & Commissioning Of Outdoor Stand Mounted Feeder Pillar With Ip65 Protection, Factory Made Fabricated Made Out Of 2.1Mm Thick Crca Sheet Steel With Door Fixed Hinges And Complete With McbS At Incoming & Outgoings ( Nos. Of Incoming & Outgoing McbS Mentioned Below ) , , Single Dial Time Switch. 20A Tp Contactor For The Automatic Switching Of [ Luminaries, Power Tool Control With 2 Nos 9A Contactors And Raise Lower Push Button, Incoming 40×16 Sq. Mm Sq. Mm ( 3.5C / 4C ) And Outgoing 16 & 25Sq. Mm Terminals. Feeder Pillar Should Be Having Following Accessories & As Directed By Engr In Charge And With Use Of Timer Controls ( In The Feeder Pillars ) With Control To Reduce The Lighting Be Created As:- [ Note:Complete All Earth Work Excavation & Cement Concrete For Foundation Necessary With Pcc ( 1:2:4 ) Type B1 ( Using 20 Mm Grade Stone Aggregate ) Complete All As Specified And As Directed. ] ( I ) 6 Pm To 10 Pm-100% ( Ii ) 10 Pm To 02 Am-66% ( Lil ) 2 Am To 6 Am-33% ( Setting Of Timer As Per This Is Contractor Responsibility ) Incomera ) 32A Tpn Mcb, 10Ka-1 Nob ) Analogue Type Volt & Ampere Meterc ) One Set Phase Indication Lamp Led Type With Nos, 6A, 220V Sp Mcboutgoingd ) 16A Tpn Mcb, 10Ka-2 Nos, 52 Supply, Fixing, Testing & Commissioning Of 12.5 High Mast Shaft And Cross Section Of Mast 20 Side Polygonal In Two Sections Suitable For 50 M / Sec Wind Speed, Material Construction S 355 Grade As Par Bs- En10025 And Standard Of Galvanization As Per Bs En Iso 1461, With Raising Lowering System Comprising, Head Frame, Luminaries Carriage Suitable To Install 6 Nos 120 Watt Ledluminaries In Symmetrical Arrangement, Double Drum Winch, 6 Mm Diameter Ss Wire Rope, Tralling Cable, Connector, Integral Power Tool Motor Manual Handle, Junction Box, Lightening Finial. Wiring Of Luminaries With Pvc Insulated Pvc Sheathed Flexible Cable Of Suitable Copper Conductor Cores As Mentioned In Perticular Specification. Construction Of Shallow Foundation With M25 Grade Concrete For High Mast Considering The Safe Soil Bearing Capacity At Site As Specified Soil Investigation Report, As Directed By Engr In Charge ( Inclusive Of Fixing As Specified Below ) . Supply Of Foundation Bolts Manufactured From Special Steel Along With Nuts, Washers, Anchor Plates And Templates. [ Complete All Earth Work Excavation & Cement Concrete For Foundation Necessary With Pcc ( 1:2:4 ) Type B1 ( Using 20 Mm Grade Stone Aggregate ) Complete All As Specified And As Directed 53 S & F Of M.V Danger Notice Plate Made Out Of 1.6 Mm Thick Mild Steel Sheet, Vitreous Enameled White, With Letters, Figures And Conventional Skull And Bones In Signal Red Colour And Fixed With 6 Nos Ms Clamps, Bolts And Nuts Of Approved Size & Nos For Lt 20 X 15 Cm Size. Notice Plate In Three Language ( English + Hindi + Local Language ) Should Be Used In Danger Notice Plate 54 Supply And Laying Of Reinforced Precast Concrete Cable Cover Made Out Of Pcc, 1:2:4 Type B-0 ( Using 12.5 Mm Graded Stone Aggregate ) Class Lv, Type 1, Flat, Size 250Mm X 150Rnm X 40Mm Complete All As Specified And Directed. 55 Supply, Laying, Testing And Commissioning Of Following Sizes Of Xlpe Sheathed, Pvc Insulated, Aluminum Conductor Armoured Cable Of 1.1 Kv Grade In Trench / Surface Of Wall / In Gi Pipe / In Hume Pipe / Along With Pole For Connection To Oh Lines, Including Fixing Hardware, Clamps, Making Good The Damaged Surfaces Etc, As Required Complete. All Cable With Stranded Conductors. ( I ) 4 Core, 16 Sq Mm 56 Supply, And Making End Termination With Brass Compression Gland For Following Sizes Of Xlpe 10 Sheathed, Xlpe Insulated, Aluminium Conductor Armoured Cabte Of 1.1 Kv Grade Including Aluminium Thimbles And Connections Etc, As Required. 57 ( I ) 3.5 Core, 35 Sq Mm 58 ( Il ) 4 Core, 16 Sq Mm 59 ( Iii ) 4 Core 6 Sq Mm 60 Earthing For Poles & Other Machinery / Equipment Using Gi Wire As Earthing Lead And Earthing Complete With Galvanized Steel Earth Pipe Electrode 40 Mm Bore Medium Grade 2.5 M Length Buried Directly And Preferably Vertically In Ground With Top Edge Not Less Than 1.25 Meters Below Ground Level Connected With Earthing Lead Of 4Mm Dia. Galvanized Iron Fo Steel Wire All As Shown In Plate No 4 To The Earthing Test Point All As Specified And Indicated Including Earth Pit Land Trench Excavation Removal Of Surplus Soil, Pc Pit Cover With Fitting Hook, Funnel With Watering Pipe Wire Mesh Charcoal, Salt, Testing. 61 Earthing Compble With Gilvanised Steel Earth Plate Electrode 600 X 600 X 6.0 Mm Thick, Buried Directly In Ground ( Earth Pit Not Less Than 2.25 M Deep Below Ground Level ) With Top Edge Of The Plate Not Less Than 1.5 M Below Normal Ground Level, Connected To Gl Earth Lead Wire 4.0 Mm Dia With Bolts, Nuts, Check Nuts And Washers Of Galvanised Iron Or Steel, Connected To Earthing Test Point All As Ipecified And Indicated Including Testing On Completion Including Pcc Pit And Pcc Pitcover, Funnel With Watering Pipe Of Gl 20 Mm Bore Medium Grade, Protection Of Each Lead Pipe Of Gl 20 / 25 Mm Bore Wire Mesh, Copper Lugs Etc. Including Testing And Connecting Lead From Test Point To Main Switch Or Switch Board Or Equipment To Be Earthed All Complete As Specified And Shown On Electrical Plate No. 3 Of Ssr Part-1 2009 On Page No. 497. ( Gi Wire From Test Point Shall Be Measured Separately ) 62 Returning, Filling In, Including Spreading, Levelling, Watering And Well Remmining In Layers Not Exc 25 Cm Complete All As Specified And Directed. 63 Removing Excavated Material N.Exc 50 M And Depositing Where Directed At A Level N. Exc 1.5 M Above The Starting Point Complete All As Specified And Directed. 64 Excavation In Trenches N. Exc 1.5 M Wide And N.Exc 1.5 M In Depth And Getting Out Soft / Loose Soilfor Laying Of Under Ground Cable, Foundation Of Pole And Stay Etc. Complete All As Specified And As Directed 65 M&L For Sand Cushioning To U / G Cable In Layers Of 23 Cm Thick ( 8 Cm Before Laying The Cable And 15 Cm Thick After Laying The Cable ) In Trenches Complete All As Specified And Directed.Note :-Only Puned Down Volume Shall Be Measured. 66 Supply And Installation Of 300 Mm Dia 900 Rpm, Exhaust Fan With Plastic Louvers Including Frame And Connection Up Including Provision Of Cables From Connector To Fan Complete All As Specified And Directed. 67 Supply And Installation Of 200 Mm Dia 900 Rpm, Fresh Air Fan With Plastic Louvers Including Frame And Connection Up Including Provision Of Cables From Connector To Fan Complete All As Specified And Directed. 68 Supply And Fixing Led Lights Fitting 1X 26W, 220V, Ac Decorative Box Type With Driver, Holder Including Led Tube Light Connecting Up With Three Core Flexible Copper Conductor Cable Of Suitable Size From Ceiling Rose Complete All As Specified And Directed. 69 Supply And Fixing Round Shape 12 Watt 220 Volts Ac Recessed Type With High Efficiency Pmma Diffuser Soft Glare Free Light Complete With Drivers, Holders, Led Lamp Suitable For Roof Ceiling Including Connecting Up With Three Core Flexible Copper Conductor Cable Of Suitable Size Complete Thick Crca Sheet Prewired Upto Connection Complete All As Specified And Directed. 70 S&F Switch Piano, 5 Amps Single Pole One Way Switch On Bell Push Complete All As Specified And Directed. 71 S&F Switch Piano, Flush Type Single Pole, One Way 5 Amp Complete All As Specified And Directed. 72 S&F Buzzer, Ac 240V, Single Pole, Complete All As Specified And Directed. 73 Supply And Fixing Of 1X 28 W Weather Proof Fluorescent Tube Light Single Tube Box Type Complete With Electronic Ballast Capacitors String Loaded Rotor Type Lamp Holder Starters, Holder Connector Block Etc With Acrylic Cover Made Form Methancrylate Sheet And All Accessories Prewired Complete With 28 Watts Tube And 1.5 Mt Long 40 Mm Dia Gi Pipes Complete All As Specified And Directed. 74 M &Lforinsulating Ofgi Pipe 15 / 20Mm Diainsulated And Insulation Secured With Tape And Covered With Aluminum Sheet From Hot Water Tankto Supply Point Duly All As Recommended By The Manufacturer. 75 Supply & Fixing Switch Board Withhylum Sheet Of Size 5°X5 & 8X5 Complete All As Specified And Directed. 76 Supply & Fixing Switch Board Withhylum Sheet Of Size 8 X 5 Complete All As Specified And Directed.

Corrigendum Details

Sr No CorrigendumDate Corrignedum CorrigendumType NewSubmissionDate
1 16-12-2022 Corrigendum BOQ 31-12-2022
2 31-12-2022 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 07-01-2023

Key Value

Document Fees
INR 500 /-
EMD
INR 51148.0 /-
Tender Value
INR 25.57 Lakhs /-
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail