Tender For Gram Panchayat Kudi Bhagatasani Mein Isaro Ke Paas Khel Maidan Me Open Zym Kary, Jodhpur-Rajasthan

Supply Of Chest Press Cum Seated Puller • Dimensions: - 2000Mm ( Length ) X 710Mm ( Width ) X 2200Mm. ( Height ) . • Safe Area: - 3.0 Mtr X 1.7Mtr. • Chest Press Cum Seated Puller Equipment Made Up Of C Classm.S. Pipe Of Different Nb. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters • The Center Pipe Is Of 100Nb Made Up Of C Classm.S. Pipe. • The Bottom Welded With Support Of M.S. Round Plate Of 0250 Mm & 10Mm Thickness. • The Connecting Pipes Are Made Up From 25Nb C Classm.S. Pipe. • The Handle Frame Is Made Up From 32Nb C Classm.S. Pipe. • To Build Structure Bushes Are Used Which Are Made From Seamless Pipe Of 50Mm O.D. And 6Mm Thickness As Well As 50Mm Diameter Solid Bar Is Used • The Foundation Used For Fixing Is A Structure And Made From Center Pipe Ofm.S. Of 80 Nb C Class Welded With M.S. Round Plate Of 0250 Mm & 10Mm Thick. Main Pipe Supported With 25 Mm X 25Mm M.S. Angles Of 3 Mm Thickness And 20Mm X 40Mm Crc Square Pipes Of 3Mm Thickness. • The Seats And Back Rests Are Fitted On The Outer Frames Are Made Up Of M.S. Sheet Of Size 330 Mm X300 Mmx2mm Thickness And Deep Drawn And Pressed In Tools And Dies To Have Uniform Radius Of 20 Mm With No Sharp Edges. • Closing Caps Are Made Up Of High Quality Fiber Reinforced Plastic Material. • Pins Used Of Diameter 25Mm And 17Mm Are Made Up From Sae 8620 Bright Material. • The Bearings Used Are Of 6205Zz &6203Zz Permanent Lubricated Sealed Bearing Of Reputed Brand • High Tensile Steel With Galvanized Nuts & Bolts Are Used For Assembly , Triple Twister. Dimension – 1980Mm ( Length ) X 1980 Mm ( Width ) X 2080 Mm ( Height ) Safe Area – 2.5 Mtr. X 2.25 Mtr. Tripletwister Equipment Is Made Of Form Ms Pipe Of Different No. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters. The Central Main Pipe Is @ 115 Mm X 5 Mm Thick Ms Pipe. The Bottom Of Central Pipe Is Welded With Support Of Ms Round Plate @ 225 Mm & 8 Mm Thick. The Bottom Of Frame If Made From 90 Mm X 3 Mm Thick Ms Pipe Each Bottom Frame Are Connected To Central Pipe With Two Half Curved Shaped Ms Flat ( 100 Mm X 203 Mm ) The Handle Frame Is Of 35 Od X 3 Mm Thick Made Form Ms Pipe Is Capsule Shapes. There Is Hole Of 25Mm On Base Plate For The Adjustment The Level Of The Equipment. Pins Sued Of Diameter, 35Mm Are Made From Sae 6620 Bright Material There Are Two Types Of Bearing Used Tapered Bearing And Ball Bearing ( 6306 Zz Permanent Lubricated Seated Bearing ) Of Reputed Brand The Whole Console Of Pins Is Designed In Lock And Key And The Special Tt Spring Lock Pattern Is Sued So That The Bearing And The Plate Console Cannot Be Take Out There Will Be Special Spring Lock Between The Bearing Block Safety. High Tensile Sheet With Galvanized Nuts And Bolls Are Sued For Assembly. The Specialized Powder Coating Of Texture Color In Used. The Foundation Used For Fixing The Central Pole Made From The Combination Of3 Rod And The @ 225 Mm &6 Mm Thick M.S. Plate The Rod Is 760 Mm Long And ¾”Thick & At The One End Of The Rod Bsw Threading Is Done For The Adjustment Of The Level Of The Main Frame These Three Rods Are Welded To Together With 35Mm X 35 Mm Ms Angle Of 5 Mm Thickness. The Top Ends Of The Structure Are Closed And Property Welded. The Twister Plate Are Made From @ 350 Mm X 6 Mm Thick Chakkar Plate The Border Cover Of Plate Is 50 Mm X 6 Mm Thick M.S. Flat And The Base Of The Twister Plate Is Welded With Special Pin Console ( @60 Mm & 15 Mm Thickness ) And With The Flat For Support. The Bottom Of The Bottom Frame Is Welded With Support If T Shaped C Channel Heavy Gauge ( 76 Mm X 38 Mm ) , Parallel Bar Dips Dimension – 1700Mm ( Length ) X 685 Mm ( Width ) X 1930 Mm ( Height ) Safe Area – 2 Mtr. X 1 Mtr. Parallel Bar Dipsequipment Is Made Of Form Ms Pipe Of Different No. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters. The Central Main Frame Is Made Up Of Combination Of ( @ 90 Mm X 3 Mm & 100 Mm X 50 Mm ) Ms Pipe And Cr Sheet ( 20X12 ) Of 16 Gauge For Support & Display. Bottom Frames Is Made Up Of ( @ 90 Mm X 3 Mm ) Thick Ms Pipe. 1676 Mm Long & 279 Mm Height. The Linkage Handle For The Parallel Bar Dips Are Made Up Of @ 50 Mm Ms Pipe Of Heavy Gauge.Both The Side Handles Are Kept Of Different Level So That Everyone Can Used It At One End Handle Should Be At 1641 Mm Height From The Base Frame And Other At 914 Mm Height From The Base Frame. High Tensile Sheet With Galvanized Nuts And Bolls Are Sued For Assembly. The Specialized Powder Coating Of Texture Color In Used. The Foundation Used For Fixing The One Side Of Bottom Frame Is Made From The Combination Of 6 Rod And The 2 Thick Plate ( 228.6 Mm & 8 Mm ) The Rod Is 760Mm Long And ¾” Thick And At The One End Of The Rod Bsw Threading Is Done For The Adjustment Of The Level Of The Main Frame These 6 Rods Are Welded To Together With Support 35Mm X 35 Mm Ms Angle Of 5 Mm Thickness And The Adjustment Is Done By The Nuts.Same To Be Done On Other Side. All The Ends Of The Structure Are Closed And Property Welded. , Air Walker Dimension – 2501Mm ( Length ) X 75 Mm ( Width ) X 2095 Mm ( Height ) Safe Area – 2.5 Mtr. X 1.5 Mtr. The Air Equipment Is Made Of Form Ms Pipe Of Different No. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Mm. The Central Main Frame Is Made Up Of Combination Of @ 90 Mm X 3 Mm & 100 Mm X 50 Mm Ms Pipe And Cr Sheet ( 20”X12” ) Of 16 Gauge For Support & Display. The Pillars Of Main Frames Is Made Up Of @ 90 Mm X 3 Mm Thick Ms Pipe. The Sleeve Frame Is Made Up Of 63.5 Mb, This Sleeve Can Be Disassemble From Main, The Sleeve Is Supported With Flat And O 63 Mm Ms Pipe From The Top And At The Other End Foot Rest Is Attached With Two Flat ( 254 Mm X 63 Mm ) The Ms Pipe Of Dia 50 Mm Is Bended In C From To Attach The Main Frame And Pillars. The Foot Rest ( 152 Mm X 365 Mm ) Is Fixed On The Sleeve Frame, Foot Rest Is Made Up Of Combination Of Chakkar Plate & Flat ( 30.48 Mm ) Is Welded On Border. The Main Frame And Pillars Are Attached With Supporting Pillars Dia 50 Mm Ms Pipe.For Safety And Supporting Reasons. The Foundation Used For Fixing The One Side Of Bottom Frame Is Made From The Combination Of 6 Rod And The 2 Thick Plate ( 228.6 Mm & 8 Mm ) The Rod Is 760Mm Long And ¾” Thick & At The One End Of The Rod Bsw Threading Is Done For The Adjustment Of The Level Of The Main Frame These 6 Rods Are Welded To Together With Support 35Mm X 35 Mm Ms Angle Of 5 Mm Thickness And The Adjustment Is Done By The Nuts & The Support Pillars.The Foundation Used For Fixing The Supporting Pillars Is Fixed By Four T Shapes C Channel Heavy Gauge ( 75 Mm X 35 Mm ) And All The T Shaped C Channel Are Joined Together With Support 35 Mm X 35 Mm Ms Angle Of 5 Mm Thickness. To Build Structure Bushes Are Used Which Are Made Form M.S. Seamless Pipe Of 63 Mm O.D. And 10 Mm Thickness. The Bearing Used Are Ball Bearing 6205 Zz Permanent Lubricated Seated Bearing Of Reputed Brand. High Tensile Sheet With Galvanized Nuts And Bolls Are Sued For Assembly. The Specialized Powder Coating Of Texture Color In Used. The Specialized Powder Coating Of Texture Colour Is Used. All The Ends Of The Structure Are Closed And Property Welded. , Cross Walker Dimension – 1930Mm ( Length ) X 990 Mm ( Width ) X 1778 Mm ( Height ) Safe Area – 2.5 Mtr. X 1.5 Mtr. The Cross Walker Equipment Is Made Of Form Ms Pipe Of Different No. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters. The Main Frame Is Made Up To Combination @ 90 Mm X 3 Mm & 100 Mm X 50 Mm Ms Pipe And Cr Sheet ( 20”X12” ) Of 16 Gauge For Support & Display & The Supporting Frame Is Made Up Of Combination Of @ 90 Mm X 3 Mm Thick Ms Pipe & 100 Mm X 50 Mm Ms Pipe, Both The Main Frame And Supporting Frame Are Joined Together Thought 100 Mm X 50 Mm Ms Pipe. The Handle Frame Is Made Up To @ 50 Mm Ms Pipe & 35 Mm Ms Pipe. To Build Structure Bushes Are Used Which Are Made Form M.S. Seamless Pipe Of 63 Mm O.D. And 10 Mm Thickness.The Linkage Frame Consist Of Portion, Each Portion Is Made Up Of Combination Ms Pipe ( 50 Mm Square ) And Ms Flat ( 50 Mm X 6 Mm Thick ) On Both The Side And The Foot Rest ( 152 Mm X 368 Mm ) Is Fixed Out He Both The Ends Of Each Portion, Foot Rest Is Made Up Combination Of Chakkar Plate & Flat ( 30.48Mm ) Is Welded On The Border. The Linkage Frame And The Handle Are Fixed On The 571 Mm X 6 Mm Thick Plate, The Bearing Shaft Of 25 Mm Dia Is Fixed On The Capasule Hole On The Ends Of Thick Plate And Convered With 70 Mm & 10 Mm Thick Plate, This Cover Is Designed In Such A Way That Is Should Cover The Outer Portion Of The Shaft And Fixed By The Spring Lock And The High Tensile Stool With Galvanized Bolls. Same On Each Every Linkage Joint. The Foundation Used For Fixing The One Side Of Bottom Frame Is Made From The Combination Of 12 Rod And The 4 Thick Plate ( 228.6 Mm & 8 Mm ) The Rod Is 760Mm Long And ¾” Thick & At The One End Of The Rod Bsw Threading Is Done For The Adjustment Of The Level Of The Main Frame These 12 Rods Are Welded To Together With Support 35Mm X 35 Mm Ms Angle Of 5 Mm Thickness And The Adjustment Is Done By The Nuts & The Support Pillars.The Foundation Used For Fixing The Supporting Pillars Is Fixed By Four T Shapes C Channel Heavy Gauge ( 75 Mm X 35 Mm ) And All The T Shaped C Channel Are Joined Together With Support 35 Mm X 35 Mm Ms Angle Of 5 Mm Thickness. To Build Structure Bushes Are Used Which Are Made Form M.S. Seamless Pipe Of 63 Mm O.D. And 10 Mm Thickness. The Bearing Used Are Ball Bearing 6205 Zz Permanent Lubricated Seated Bearing Of Reputed Brand. High Tensile Sheet With Galvanized Nuts And Bolls Are Sued For Assembly. The Cerclips Used For Assembly Are Of A24 Mm. The Specialized Powder Coating Of Texture Color In Used. All The Ends Of The Structure Are Closed And Property Welded. , Sit Up Board Double • Product Dimensions: - 1760Mm ( Length ) X 1140Mm ( Width ) X 660Mm ( Height ) . • Safe Workout Area: - 2500Mm ( Length ) X 1600Mm ( Width ) . • The Sit Up Board Double Made From C Class Gi Pipe. Center Column Made From 100Mm Nb C Classm.S. Pipe. • The Main Frame Is Of 25Mm Nb Made From C Class Gi Pipe. Frp Sheet Of 3Mm Thickness Is Molded On Main Frame. • The Remaining Frame Of The Sit Up Board Is Of 32Mm Nb Made From C Class Gi Pipe. • The Powder Coating Is Done With Pure Polyester Powder Ackzonoble Or Berger Paints With 60 To 70 Micron Thickness. • The Foundation Used For Fixing Is A Structure And Made From Center Pipe Ofm.S. Of 80 Nb C Class Welded With M.S. Round Plate Of 0250 Mm & 10Mm Thick. Main Pipe Supported With 25 Mm X 25Mm M.S. Angles Of 3 Mm Thickness And 20Mm X 40Mm Crc Square Pipes Of 3Mm Thickness. , Back Extension Dimensions: - 1400Mm ( Length ) X 700Mm ( Width ) X 820Mm ( Height ) . Safe Area: - 2.4Mtr X 1.7Mtr. Back Extension Equipment Made From C G.I. Pipe Of Different Nb Pipe. ( Nb Stands For Nominal Bore I.E. Internal Diameter Of Pipe In Mm ) . The Main Frame Is Of 50Mm Nb Made From C Class G.I. Pipe. The Foot Resting Frame Of 32Mm Nb Made From C Class G.I. Pipe. The Handle Frame Is Of 25Nb Made From C Class G.I. Pipe. The Seat Fitted On The Outer Frames I S Made Up Of M.S. Sheet Of Size 330Mm X 300Mmx2mm Thickness And Deep Drawn And Pressed In Tools And Dies To Have Uniform Radius Of 20 Mm With No Sharp Edges. The Foundation Used For Fixing Is Consists Of 50Mm Nb Made From C Class G.I. Pipe. The Footrests Are Made From Casted Aluminum Material, Having Sizes 130 X 310 X 5 Mm Thick. With The Support Of 250Mm X 115Mm X 3Mm Thick Ms Plate. The Powder Coating Done With Pure Polyester Powder O F Ackzonoble Or Berger With 60 To 70 Micron Thickness. , Leg Press • Dimensions: - 1840Mm ( Length ) X 360Mm ( Width ) X 1560Mm. ( Height ) . • Safe Area:- 2.8 X 1.4Mtr. • Leg Press Equipment Made From C Classm.S. Pipe Of Different Nb. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters • The Center Pipe Is Of 100Mm Nb Made From C Classm.S. Pipe. • The Sleeve Frame Is Of 100 Od And Of M.S. Seamless Pipe With Thickness 5Mm. This Sleeve Can Be Disassembled From Main Frame. • The Bottom Support Of M.S. Round Plate Of 0250 Mm & 10Mm Thick. • The Remaining Outer Frame Is Of 32Nb Made From C Classm.S. Pipe. • The Foundation Used For Fixing Is Structure And Made From Center Pipe Ofm.S. Of 80Mm Nb C Class Welded With M.S. Round Plate Of 0250Mm & 10Mm Thick. Main Pipe Supported With 25 Mm X 25Mm M.S. Angle Of 3 Mm Thickness And 20Mm X 40Mm Crc Square Pipe Of 3Mm Thickness. • Seat & Back Rest Provided Are Made Up Of Ms Deep Draw Quantity Of 2Mm Thickness With No Joint With Uniform Outer Edge Radius 20Mm. • The Footrests Are Made From Tasted Aluminum Material, Having Sizes 130Mm X 310Mm X 5Mm Thick. With The Support Of 310Mm X 130Mm X 3Mm Thick Ms Plate. • The Frame Of Footrests Made Up Of 25 Nb C Classm.S. Pipe. • Closing Caps Are Made Up Of High Quality Fiber Reinforced Plastic Material. • To Build Structure Bushes Are Used Which Are Made From M . S . Seamless Pipe Of 50Mm O.D. And 5Mm Thickness. , Shoulder Builder: 1 Mounting Plate Centre Pillar 2 Hinge Holding Pipe 2 Bending Pipe Cap 3 Unshaped Pipes Handles 4 Straight Pipe ( No.1 ) Straight Pipe ( No.2 ) Straight Pipe ( No. 3 ) Seat Base Pipe Back Seat Hinges Box Bracket Holder 1 A Circular Mourning Plate Of Diameter 233 Mm Thickness 8 Mm, 4 Holes On This Plate At 90. Degrees Of Which P.C.D. 17 Mm Hole Diameter Is 20 Mm. 2 On Circular Mounting Plate A Center Pillar Is Welded Diameter Of Center Pillar Is 19 Mm And Height Is 1838 Mm . 3 Cap Is Fixed On The Top Of The Pillar With Rivets. 4 At 1528 Mm Vertical Distance -2 Hinges Holding Pipes Are Welded In Opposite Directions . Hinge Holding Pipe Have Clear Hole For Screw At 177 Mm Distance. 5 Bending Pipes Are Welded To The Hinges Holding Pipe Andthe Center Pillar To Provide Mechanical Strength To The Hinge Holding Pipe. , Surfing Board • Dimensions: - 1000Mm ( Length ) X 600Mm ( Width ) X 1400Mm. ( Height ) . • Safe Area:-1.5 X 1.3Mtr. • Surfing Board Equipment Made From C Classm.S. Pipe Of Different Nb. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimeters • T H E Main Frame Is Of 80Mm Nb Made From C Classm.S. Pipe. • The Bottom Support Welded Of M.S. Plate Of 0 250 Mm & 10Mm Thickness. • The Handle Frame Is Of 25N B Made From C Classm.S. Pipe. • The Foundation Used For Fixing Is A Structure And Made From Center Pipe Ofm.S. Of 80Nb C Class Welded With M.S. Round Plate Of 0250 Mm & 10Rnm Thick. Main Pipe Supported With 25 Mm X 25Mm M.S. Angles Of 3 Mm Thickness And 20Mm X 40Mm Crc Square Pipes Of 3Mm Thickness. • Bushes Are Used 70Mm Outer Diameter With 5Mm Thickness Is Used. • The Footrests Made From High Quality Fiber Reinforced Plastic. • Closing Caps Are Made Up Of High Quality Fiber Reinforced Plastic Material. • T H E Pins Used Are Made Up Of 035 Mm Sae 8620 Bright Material. • The Bearing Used Are Of 6007Zz Permanent Lubricated Sealed Bearing Of Reputed Brand. • High Tensile Steel With Galvanized Nut Bolts Are Used For Assembly. • T H E Cerclips Used For Assembly Is Of A34. • The Powder Coating Is Done With Pure Polyester Powder Of Ackzonoble Or Berger With Minimum 60 To 70 Micron Thickness

INR 500 /-

INR 8000.0 /-

INR 4 Lakhs /-