|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.All kinds of soil |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level:1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) |
| 5 | First class brick work in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 6 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 7 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 8 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622 - 2017, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Soluble Salt Stainfree vitrified tiles.Size of tile 60x60 cm |
| 9 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 10 | Providing and fixing chequered terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete.Dark shade pigment using ordinary cement |
| 11 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 12 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-In-Charge. Extruded section Profile size 48x40 mm. |
| 13 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \"H\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \"U\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 14 | 12 mm cement plaster of mix:-Cement mortar 1:4 (1 cement : 4 fine sand) |
| 15 | 15 mm cement plaster on the rough side of single or half brick wall of mix:- Cement mortar 1:4 (1 cement : 4 fine sand) |
| 16 | Neat cement punning. |
| 17 | Providingandfixingaluminiumworkfordoors, windows, ventilators and partitions withextrudedbuilt up standardtubularsections/ appropriateZsectionsand other sections of approved make conforming to IS:733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing andthedirectionofEngineerincharge.(Glazing and paneling and dash fasteners to be paid for separately) :-A. For fixed portion of approved quality:Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 18 | Providingandfixingaluminiumworkfordoors, windows, ventilators and partitions withextrudedbuilt up standardtubularsections/ appropriateZsectionsand other sections of approved make conforming to IS:733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing andthedirectionofEngineerincharge.(Glazing and paneling and dash fasteners to be paid for separately) :-B. For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 19 | Providing and fixing glazing of approved quality in aluminum doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 20 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand andmanufacture in panelling fixed in aluminium doors,windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :-Prelaminated particle board of approved quality with decorative lamination on both side |
| 21 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :300x16 mm |
| 22 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :300x10 mm |
| 23 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm |
| 24 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 25 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 26 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 27 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approvedbrand and manufacture |
| 28 | Providing & painting communication graphis (Maternal Health, Immunisation, Yoga, Tele consultation, Drug distribution & Health awarness) about Health & Wellness Centre with approved colour on the façade with circle. Sizes of inner circle with pattern design will be as per standard ratio & as per direction of the Engineer - in - charge. |
| 29 | Providing & painting local craft pattern which encircles the windows, doors, ventilators, canopy, parapet & any projected portion of building with approved colours. The sizes of the pattern will be as per standard ratio & as perdirection of the Engineer - in - charge. |
| 30 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 31 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :18.7.2 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps |
| 32 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 33 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200mm |
| 34 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.18.73.2 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 35 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 36 | Providing and fitting fixing of C.P. brass Laboratory angle (elbow)bib cock (long handle) of approved quality conforming to IS:(indian Standard) including C.P. nipple as per direction of the Engineer in charge |
| 37 | Providing and fixing on wall face unplasticised Rigid PVC rain water, soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382leaving10mmgapforthermalexpansion:18.82.2 Single socketed pipe - 110 mm OD |
| 38 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap forthermalexpansion:(a)Coupler-110 mm |
| 39 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap forthermalexpansion:Bend 87.5°- 110mm |
| 40 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVCrainwater, soil, waste & vent pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. 110mm |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(i) 15 mm nominal outer dia .Pipes |
| 42 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 43 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 44 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support fortank. |
| 45 | Supplying and fixing of the following sizes wooden switch boards with 3mm thick bakelite cover etc. as required.254mm x 300mm (10\" X 12\") :- |
| 46 | Supplying & fixing of following ratings isolator in the existing MCB DB including connection etc as required:-63 amps TP isolator:- |
| 47 | Providing and fixing of 3/6 pin 16/20 amps plug point withmodulartype 16/20ampsswitch andsocketincludingconnectionwith 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) onmodular concealedswitch board with cover plate earthing the 3rd pin etc. as required. |
| 48 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:- 2 X 1.5 + 1 X 1.5 sq mm |
| 49 | Supplying & fixing of 1200 mm sweep white color AC ceilingfan with brush less dirrect current (BLDC) motor having class B insulation, power factor not less than 0.9 complete with 300 mm down rod, canopies, shackle kit, 3nos blades, safety rope including wiring the down rod with 2x1.5 sqmm PVC insulated copper conductor cable(FR)(BEE 5star/minimum service value 6.0 m3/min/W & tolerance as per IS:374-2019) : - |
| 50 | Supplying & fixing of electronic 5 step fan regulator in existing switch board including necessary connection etc as required:- |
| 51 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connectionas required:-6 to 32 amps SP MCB. |
| 52 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc.as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-Surface mounted box type batten suitable for double 18/20 watt integrated LED tube lamp (without lamp):- |
| 53 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:-18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100lm/watt):- |
| 54 | Supplying & installation of 300 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) :- |
| 55 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-25 watt LED street light fixture with integral driver and secondary lens (IP 66):- |
| 56 | Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12\"x 12\" having locking arrangement including CC work, holes on earth pipe etc. as required. |
| 57 | Supplying and fixing of the following modular accessories including necessary connection etc. as required.:-20/25 amps single phase motor starter switch (2M). |
| 58 | Charges for drilling and boring of pilot hole in any soil strata by water jet or any suitable method including collection of samples at various suitable levels and preservation of samples in polythene bags / sample boxes and disposal of excess soil or mud and maintain the pilot hole properly and required staging as per specification ( IS : 2800 ) and direction of the Engineer-in-charge.A. upto 100 metre depth. i. 40 mm dia |
| 59 | Charges for reaming of pilot hole in any soil strata by water jet or any suitable method and disposal of excess soil or mud including the cost for material as required to maintain the pilot hole properly and required staging as per specification ( IS : 2800 ) and direction of the Engineer-in-charge. A. upto 100 metre depthi. from 40 mm to 100 mm dia |
| 60 | Providing, fitting, fixing, and lowering UPVC \"CM\" casing pipe as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge.i. 40 mm NB |
| 61 | Providing, fitting, fixing, and lowering UPVC ribbed screen pipes as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge.i. 40 mm NB |
| 62 | Providing and fitting fixing G.I. pipe (medium class) conforming to IS : 1239 for OHP of approved quality as per specification and direction of the Engineer-in-charge. i. 40mm dia |
| 63 | Charges for threading of G.I. pipe, as per chapter-20 of CPWD specification and direction of the Engineer-in-charge.i. 40 mm dia. Pipe |
| 64 | Providing and fitting fixing of Bottom Cap ( UPVC ) as per specification and direction of the Engineer-in-charge. i. 40mm dia |
| 65 | Providing and fitting fixing Shallow well hand pump (C.I.) No.6 (90 mm) as per IS:8035/1999complete set as per specification and direction of the Engineer-in-charge. |
| 66 | Charges for development of ordinary hand tube well by pumping out the turbid water till clean sand free water is obtained as per chapter-20 of CPWD specification and direction of the Engineer-incharge. |
| 67 | Charges forfitting fixing of hand pump complete as per chapter-20 of CPWD specification and direction of the Engineer-in-charge. |
| 68 | Providing and fitting fixing Nutsboltsfor OHP of approved quality as per specification and direction of the Engineer-in-charge. |
| 69 | Providing and fitting fixing ofM.S. Piston rod for OHP of approved quality as per specification and direction of the Engineer-in-charge. |
| 70 | Providing and fitting fixing ofLeather bucket conforming to IS :1015 for OHP of approved quality as per specification and direction of the Engineer-in-charge. |
| 71 | Providing and fitting fixing of C.I. base valve weight for OHP as per specification and direction of the Engineer-in-charge. |
| 72 | Providing and fitting fixing of C.I. base plate for OHP as per specification and direction of the Engineer-in-charge |
| 73 | Providing and fitting fixing ofC.I.Plunger for OHP of approved qualityas per specification and direction of the Engineer-in-charge. |
| 74 | Providing and fitting fixing C.I. head cover for OHP of approved qualityas per specification and direction of the Engineer-in-charge. |
| 75 | Providing and fitting fixing C.I. handle for OHP of approved qualityas per specification and direction of the Engineer-in-charge. |
| 76 | Providing and fitting fixing G.I. screw for OHP of approved quality as per specification and direction of the Engineer-in- charge. |
| 77 | Charges for threading of Connecting Rod, as per chapter-20 of CPWD specification and direction of the Engineer-in- charge |
| 78 | Charges for fitting, fixing, and lowering UPVC \"CM\" casing pipe as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge.40 mm NB |
| 79 | Charges for fitting, fixing, and lowering UPVC ribbed screen pipes as per IS:12818 for Mark II / III / OHP as per specification and direction of the Engineer-in-charge. 40 mm NB |
| 80 | Charges for fitting fixing of Bottom Cap ( UPVC ) as per specification and direction of the Engineer-in-charge. |
| 81 | Providing and fixing 1HP Single phase monoblock pump set (Pump & motor) ISI marked and approved quality(Kirloskar ) or equivalentwith necessary connection with delivery and suction line complete as per direction of the engineer in charge. (cost of electrical accessories and connection etc to be paid separately) |
