Bids Are Invited For 1 Book Shelf Supply And Installation Of Office Table 4 Door Bookcase: It Should Have Multi Bend Construction With Press Fit Fasteners Free Design. It Should Have 10 Lever Cam Lock. Door Should Have Equalizing Scissor Mechanism For, Jabalpur-Madhya Pradesh

Bids Are Invited For 1 Book Shelf Supply And Installation Of Office Table 4 Door Bookcase: It Should Have Multi Bend Construction With Press Fit Fasteners Free Design. It Should Have 10 Lever Cam Lock. Door Should Have Equalizing Scissor Mechanism For Easy Opening And Closing. All Steel Components Should Undergo Eight Tank Anti Rust Treatment And Oven Baked Epoxy Polyester Powder Coated With 50-60 Dry Film Thickness. The Crca Steel Sheet Used For The Top Should Be 0.8 Mm Thick, As Per Is-513 1994. The Bookcase Should Have Clear Opening Of 330 Mm. It Should Have Removable Glass Door With 3 Mm Glass ( 4 Nos. ) . It Should Have 4 Shelves With Stiffener. It Should Have Scratch Hardness Of 3 Kgs As Bs-3900 Part E2 1970, Is-101. It Should Sustain Salt Spray Test Of 1000 Hrs. As Is 101. Overall Size: 174.2 Cm ( H ) X 91.4 Cm ( W ) X 32.0 Cm ( D ) . 8 2 Magzine Stande Suppy And Installation Of Magzine Stande Unit Size Of 900 Mm ( W ) X 450 Mm ( D ) X 1830 Mm ( H ) , Construction & Material Rigid Knock Down Construction. Panels Made From Crca* 0.6 Mm Thk ( ±0.07Mm ) And Front Frame Made From Crca*0.8Mm Thk ( ± 0.8 Mm ) . *Crca ‘D’ Grade As Per Is 513, Configuration ( Racks ) 5 Level Racks, Display Tray Suitable For Fullscape Size Magazines, Periodicals.Aesthetically Appealing Metal Tray At An Angle For Easy Viewing Receding Facility To Access The Storage Behind. Sliding On Plastic Rollers.Behind Storage Shelving Each Of 5 Level Has A Behind Storage Shelf Uniformly Distributed Load Capacity Per Each Shelf Is 40 Kg Maximum.Screw Type Leveler With Hex Plastic Base ( Add In Unit Height Min.8 Mm & Additional 5 Mm Max For Adjustment ) Finish Epoxy Polyester Powder Coated To The Thickness Of 50 Microns ( + / -10 ) 4 3 Office Almirah Supply And Installation Of Office Almirah: It Should Have Multi Bend Construction With Interlocking Design And Full Length Over Lapping Doors And Sides. It Should Have Three Way Bolting Mechanism. All Steel Components Should Undergo Eight Tank Anti Rust Treatment And Oven Baked Epoxy Polyester Powder Coated With 50-60 Dry Film Thickness. The Crca Steel Sheet Used For The Body Is Of 20 Swg / Guage, As Per Is-513 1994. It Has 5 Shelves Made Of 22 Swg / Guage Crca Steel Sheet. It Has Six Lever Mazak Zinc Plated Godrej Lock. It Has Scratch Hardness Of 3 Kgs As Bs-3900 Part E2 1970, Is-101. It Sustains Salt Spray Test Of 1000 Hrs. As Per Is 101. It Should Have 4 Shelves Made Of 0.8 Mm Thick Crca Steel Sheet. It Should Have Six Lever Mazak Zinc Plated Godrej Lock. It Should Sustain Salt Spray Test Of 1000 Hrs. As Per Is 101. Overall Size: 198.0 Cm ( H ) X 91.5 Cm ( W ) X 48.5S Cm ( D ) 4 Sofa 3 seater Supply and installation of office table 3 Seater Premium lounge Chair Cushioned for Waiting Rooms of size: W 1640 mm X D 700 mm X H 785 mm, Seat height: 435 mm, SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two ends of the connecting beam assembly to form the leg-cumarmrest assembly. It is made of a MS. E.R.W. tube dia. 3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube dia.3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The seat/back assemblies are mounted on one of the tie- member which has 5cm x 5.5cm long x 0.5cm. thk MS. Std. angles welded to mount the seat and back. SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). BACKREST ASSEMBLY: The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitumoulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholstery cover. BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T). ADJ. GLIDES: The adj. glide is injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. 5 Sofa 1 seater Supply and installation of office table 1 Seater Premium lounge Chair Cushioned for Waiting Rooms of size: W 605 mm X D 700 mm X H 785 mm, Seat height: 435 mm, SIDE FRAME ASSEMBLY: The side frame assembly is fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It is made of a MS. E.R.W. tube dia. 3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube dia.3.81cm. (1 1/2”) x 14 BG. thk. and black powder coated. The seat/back assemblies are mounted on one of the tie- member which has 5cm x 5.5cm long x 0.5cm. thk MS. Std. angles welded to mount the seat and back. SEATREST ASSEMBLY: The seat rest assembly consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 23 - 27 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover. SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). BACKREST ASSEMBLY: The backrest assembly is flexing type and consists of a fabricated inner-frame assembly insitu-moulded with Polyurethane foam having density = 45 +/- 2 Kg./cm3. The hardness of the P.U. foam = 16 - 20 Kgs. on Hampden m/c. for 25% compression of the foam. The complete moulded backrest assembly is covered with a replaceable fabric upholstery cover. BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T). ADJ. GLIDES: The adj. glide is injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. 12 6 Centre Table Supply and installation of center table with glass top 10 mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure It is a welded assembly made in SS202 grade having dia.12mm as per IS:1762 6 7 Executive Table Supply and installation of office table Worksurface of size 1500 mm W x 750 mm D X 728 mm H to be made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges to be duly sealed with 2mm thick PVC Edgebanding. Understructure - Modesty Panel to be made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges to be duly sealed with 2mm thick PVC Edgebanding Rectangular Frame to be made of fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Legs to be made of fabricated component in 38mmx25mmx1.2mm thick MS ERW Tube (IS:7138), Finish: Powder coat (Epoxy polyester) Plastic Cap for Cable to be Injection Moulded Polypropylene. Leveler glide for Leg to be nylon 6 & MS Bolt Storage/Pedestal - Shell to be made of 0.6mm thick CRCA (IS:513) , Finish: Powder coat (Epoxy polyester). Drawer tray to be made of 0.6mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Drawer front to be made of 0.8mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Frame assembly to be made of 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Lock to be 10 Lever Cam Lock. Handle to be Injection Moulded Polypropylene. 2 8 Executive Table Supply and installation of office table Worksurface of size 1350mm W x 600 mm D X 728 mm H to be made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges to be duly sealed with 2mm thick PVC Edgebanding. Understructure - Modesty Panel to be made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges to be duly sealed with 2mm thick PVC Edgebanding Rectangular Frame to be made of fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Legs to be made of fabricated component in 38mmx25mmx1.2mm thick MS ERW Tube (IS:7138), Finish: Powder coat (Epoxy polyester) Plastic Cap for Cable to be Injection Moulded Polypropylene. Leveler glide for Leg to be nylon 6 & MS Bolt Storage/Pedestal - Shell to be made of 0.6mm thick CRCA (IS:513) , Finish: Powder coat (Epoxy polyester). Drawer tray to be made of 0.6mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Drawer front to be made of 0.8mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Frame assembly to be made of 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Lock to be 10 Lever Cam Lock. Handle to be Injection Moulded Polypropylene. 2 9 3 Seater chair Supply and installation of 3 Seater Lounge Chair having Seat Shell to be a welded assembly of seat, back and side frame. The Seat & Back frame is to be made up of 1.2mm thk CR steel with Oblong perforations. This is to be welded with side frame of size 32mm width x 5mm thk HR steel. The welded assembly is to be powder coated . The seat shall have have front waterfall edge to provide popliteal clearance for comfortable seating. It shall also have buttock suppport curve for comfartable sitting. SEAT Size- 47.8cm W x 44.6cm D. Back Size- 41.6cm W x 23cm H. Understucture:- Shall consist of connecting beam and leg assembly made up of MS ERW oblong tube of size 75mm x50mm x 2mm thk it shall be welded stucture assembly in powder coating which is to be fitted with shoes and levelers in nylon. Connecting beam shall be fitted with snap locking end cap. Armrest: Armrest assembly shall consist of armrest frame and armrest pad. The Armrest frame size shall be 31.7mm x 4.7mm thk HR steel and it should be powder coated. Armrest pad shall be injected moulded in Nylon and is to be fitted on armrest frame. Overall Dimensions 169.5cm W x 63.8cm D x 44.1cm SH x 78.5cm H. Total Quantity : 57

Refer document

INR 29403.0 /-

INR 14.70 Lakhs /-