Repair To Steel And Wooden Furniture And Re Canning Of Chairs At Dhar Road Under Ge ( Army ) Dhar Road- 1 Schedule A Part-I Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Bed Plytop Wooden ( Fd 246 / 247 ) , S&F New Compo, Udhampur-Jammu And Kashmir

Repair To Steel And Wooden Furniture And Re Canning Of Chairs At Dhar Road Under Ge ( Army ) Dhar Road- 1 Schedule A Part-I Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Bed Plytop Wooden ( Fd 246 / 247 ) , S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 2 Head Rest As Shown On Drawing 3 Foot Rest As Shown On Drawing 4 Long Rail Made Of Ist Class Hard Wood 5 Short Rail Made Of Ist Class Hard Wood 6 Stiffener Made Of Ist Class Hard Wood 7 Right Angled Ms Bracket 200Mm Long X 25Mm Wide X 3Mm Thick Duly Fixed With Screw 8 12Mm Thick Bwr Ply Wood Top In One Piece 9 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Chair Dining ( Fd-203 / 279 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 10 Rear Leg 11 Front Leg 12 Side Rail With Holes For Weaving ( Spacing Of Holes Shall Be As Per Old One ) 13 Front / Back Rail With Holes For Weaving ( Spacing Of Holes Shall Be As Per Old One ) 14 Bottom Stiffener 15 Back Stiffener 16 Provn Of Four Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Chair Made Out 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 17 Pvc / Rubber Shoe As Per Sample Approved 18 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Chair Writing ( Fd-261 / 280 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 19 Rear Legs 20 Front Legs 21 Side Rail With Holes For Weaving ( Spacing Of Holes Shall Be As Per Old One ) 22 Front / Back Rail With Holes For Weaving ( Spacing Of Holes Shall Be As Per Old One ) 23 Bottom Stiffener 24 Back Stiffener 25 Arm Rest 26 Provn Of Four Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Chair Made Out 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 27 Pvc / Rubber Shoe As Per Sample Approved 28 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Chair Diningofficers ( Fd / E6 / Map / 10 & Fd / E6 / Map / 10 ( R ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 29 Rear Leg 30 Front Legs 31 Side Rail Of Seat Frame 32 Front / Back Rails Of Seat Frame 33 Seat Made Out Of 75Mm Foam Cushioned Of 40 Density Covered With Fabric As Approved By Engr-In-Charge Fixed On12mm Thick Ply 34 Bottom Stiffener 35 Vertical Back Stiffener 36 Provn Of Four Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Chair Made Out 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 37 Pvc / Rubber Shoe As Per Sample Approved 38 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Chair Easy ( Fd-229 ) -S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 39 Rear Leg 40 Front Leg 41 Side Rail 42 Front / Back Rail 43 Back Stiffener 44 Bottom Stiffner 45 Arms Rest 46 Pvc / Rubber Shoe As Per Sample Approved 47 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Theteapoy ( Fd-278 / 382 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 48 Legs 49 Long Rail 50 Short Rail 51 Side Stiffener 52 Centre Stiffener 53 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 54 Pvc / Rubber Shoe As Per Sample Approved 55 Provn Of Eight Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Teapoy Made Out 30Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 56 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thepeg Table ( Fd-236 / 277 / 384 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 57 Legs 58 Long Rail 59 Short Rail 60 Side Stiffener 61 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 62 Pvc / Rubber Shoe As Per Sample Approved 63 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thepeg Table ( Fd-236 / 277 / 384 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 64 Legs 65 Long Rail 66 Short Rail 67 Drawer Made Out Prelaminated Mdf Board And 6Mm Thick Commercial Ply At Bottom And Fitted With One 100Mm Chromium Plated Handle 68 Bottom Centre Stiffener 69 Bottom Side Stiffener. 70 Provn Of Six Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Table Made Out Of 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 71 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 72 Pvc / Rubber Shoe As Per Sample Approved 73 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thetable 900Mm X 600Mm With Drawer And Without Drawer ( Fd-283 / 284 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 74 Legs 75 Long Rail 76 Short Rail 77 Bottom Side Stiffener 78 Bottom Centre Stiffener 79 Drawer Made Out Prelaminated Mdf Board And 6Mm Thick Commercial Ply At Bottom And Fitted With One 100Mm Chromium Plated Handle 80 Provn Of Six Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Table Made Out Of 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 81 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 82 Pvc / Rubber Shoe As Per Sample Approved 83 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thetable Dining 06 Person ( Fd-239 / 273 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 84 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 85 Legs 86 Long Rail 87 Short Rail 88 Stiffener 89 Provn Of Eight Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Table Made Out Of 40Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 90 Pvc / Rubber Shoe As Per Sample Approved 91 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thetable Dining 08 Person ( Fd-239 / 273 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 92 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 93 Legs 94 Long Rail 95 Short Rail 96 Stiffener 97 Provn Of Eight Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Table Made Out Of 40Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 98 Pvc / Rubber Shoe As Per Sample Approved 99 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thetable Dressing Ladies ( Fd-251 / 378 / 395 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 100 5Mm Thick Mirror Of Size 365Mmx1220mm With Back Ply Of 6Mm Thick Commercial Plywood And Wooden Frame Of Existing Shape & Size. Make- Saint Gobin / Gold Plus 101 Sliding Glass Shutter Of 3Mm Thick As Per Existing. 102 Drawer Of 6 Mm Thick Ply Wood Commercial With 18Mm Pre-Laminated Mdf Board As Per Existing Shape And Size 103 Knob As Per Sample Approved 104 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Side Board ( Fd-241 / 371 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 105 Top 106 Bottom 107 Side 108 Drawer Of 6 Mm Thick Ply Wood Commercial With 18Mm Pre-Laminated Mdf Board As Per Existing Shape And Size 109 Shutter Made Of 18Mm Thick Prelaminated Mdf Board With Hinges 110 Back Shall Be Made Of 6Mm Thick Commercial Plywood. 111 Bottom Frame With 4 Nos Of Legs Shall Be Made Of Ist Class Hard Wood 112 Knob As Per Sample Approved 113 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table Bed Side ( Fd-248 / 276 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 114 Top 18 / 19Mm Thick Both Side Prelaminated Mdf Board Fixed With Pvc Edge Band Tape 115 Side Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Fixed With Pvc Edge Band Tape 116 Shelf Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Fixed With Pvc Edge Band Tape 117 Bottom Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Fixed With Pvc Edge Band Tape 118 Back Shall Be Made Of 6Mm Thick Ply Wood Commercialas Per Existing Shape And Size Andshown In Drgs And Directed 119 Leg Frame With 4 Nos Leg And Stiffener As Per Drawing Made Ist Class Hard Wood ( Teak ) Duly French Polished. 120 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table Centre ( Fd-274 / 375 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 121 Legs 122 Long Rail 123 Short Rail 124 Side Stiffener 125 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 126 Pvc / Rubber Shoe As Per Sample Approved 127 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table 900Mm X 900Mm ( Fd-291 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 128 Legs 129 Long Rail 130 Short Rail 131 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 132 Provn Of Eight Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Table Made Out Of 35Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 133 Pvc / Rubber Shoe As Per Sample Approved 134 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table Dressing Gents ( Fd-230 / 379 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 135 Looking Glass Complete With Frame And Back Ply. Make- Saint Gobin / Gold Plus 136 Drawer Of 6 Mm Thick Ply Wood Commercial With Front 18Mm Pre-Laminated Mdf Board And Knob As Per Existing Shape And Size 137 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Hat Stand With Mirror ( Fd-Fd-233 / 361 / Fd-362 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 138 5Mm Thick Mirror Of Size 300Mmx440mm . Make- Saint Gobin / Gold Plus 139 4Mm Thick Commercial Plywood For Back 140 Chromium Plated Ms Pegswith Screw As Approved By Engineer-In-Charge 141 Wooden Furniture: Taking Down Worned Out / Unsv Components Of Thesofa Set ( Fd-281 / 373 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 142 Foam Cushion For Sofa Set Size 525X525x100mm, 40 Density, Make-Sleepwell Duly Covered With Best Quality Tapestry Cloth As Approved By Engineer-In-Charge Complete All As Directed And Specifiednote:-Rate Of Tapestry Cloth Shall Not Be Less Than Rs 250 / - Per Rm 143 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Chair Dining For ( JcoS / OrS ) Fd / Map-Ii / 05S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 144 Rear Leg 145 Front Leg 146 Side Rail With Arrangement For Fixing Of Pvc Sheet 147 Front / Back Rail With Arrangement For Fixing Of Pvc Sheet 148 Bottom Stiffener 149 Back Stiffener 150 Pvc Sheet Of Good Quality As Approved By Engineer-In-Charge 151 Provn Of Four Nos Of Wooden Tringular Bracket Of Size 75Mm X 75Mm To Each Chair Made Out 25Mm Thick Hard Wood And Shall Be Fixed With Adhesive And Screws As Directed By Engineer-In-Charge 152 Pvc / Rubber Shoe As Per Sample Approved 153 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Bed Side ( Map ) ( Fd / E-6 / Map / 15 ( R ) ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 154 Top 155 Side 156 Back Ply Of 6Mm Thick Commercial Plywood Of Existing Shape & Size 157 Drawers Made Out Of 18 Mm Thick Prelaminated Particle Board With Edging 158 Chromium Plated Handle 100Mm Long 159 Telescopic Channelof Good Quality. 160 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table Dressing Ladies Incl Stool ( Map ) ( Fd / Map-Ii / 07 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 161 5Mm Thick Mirror Of Size 365Mmx1220mm, Make- Saint Gobin / Gold Pluswith Back Ply Of 6Mm Thick Commercial Plywood And Wooden Frame Of Existing Shape & Size. 162 Sliding Glass Shutter Of 3Mm Thick As Per Existing. 163 Drawer Of 6 Mm Thick Ply Wood Commercial With 18Mm Pre-Laminated Mdf Board As Per Existing Shape And Size With Telescopic Channel 164 Foam Cushion 75Mm, 40 Density Covered With Fabric On Seat To Be Fixed On 6Mm Thick Ply On Stool As Per Existing Shape And Size 165 Wheel At The Bottom Of Stool As Per Existing Shape And Size 166 Wooden Furniture: Taking Down Worned Out / Unsv Components Of The Table Writing Folding ( Ce / Td-1139 / 97 ) S&F New Component Without Any Crack / Any Defects As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 167 Top Of Pre-Laminated Mdf Board 18Mm Thick Ewith 20Mm Thick Teak Wood Lipping Alround. Top Of The Table Should Be Fitted With 20Mm X 20Mm Size Paino Type Hinges On Long Rail Fixed On Wall As Per Drg 168 Leg ( Folding ) Of Size 50Mmx30mm Of First Class Teak Wood With Rubber Shoe 169 Long Rail Of Size 1145Mm X 75Mm X 40Mm Of First Class Teak Wood 170 Tower Bolt 75Mm Long Of Aluminium Fixed On Wooden Block Of Size 80Mmx 40Mmx40mm Thick 171 Chain To Hold The Table Writing, As Per Drg 172 Wooden Plug Of Size 40X40x75mm Embeded In 100X100x1 / 2 Bk Pcc Top Long Rail Of First Class Teak Wood With Rubber Shoe, As Per Drg 173 Re-Canning Of Chairs : Re-Canning Of Wooden Chairs, Dressing Stool, Bin Solied Linen As Per Godrej Pattern With 2 Mm Wide Half Round Superior Quality Cane Plastic After Taking Out Existing Cane.Border Of Canning Shall Be Woven With 4 Mm Half Round Plastic Cane Of Superior Quality As Shown In Drawing And Directed By Engineer-In-Charge. 174 Polishing Of Wooden Furniture Items : All Wooden Surfaces Of The Following Wooden Furniture Itemswheather Exposed To View Or Not When Placed In Position Shall Be Polised With High Gloss French Polish To Be Finished As Directed By Engineer-In-Charge Duly Preparation Of Surface With Emery Paper And Applying Putty As And Where Required. 175 Bed Plytop Wooden - Fd 246 176 Chair Dining Fd-228 / 270 / 279 177 Chair Writing Fd / 261 / 280 178 Chair Dining OfficerS Fd / E6 / Map / 10 ( R ) 179 Chair Easy Fd-229 180 Teapoy ( Fd-278 / 382 ) 181 Peg Table ( Fd-236 / 277 / 384 ) 182 Table Writing ( Fd-275 ) 183 Table 900X600mm With Drawer And Without Drawer 184 Table Dining 6 Presons ( Fd-239 / 273 ) 185 Table Dining 6 Presons ( Fd-239 / 273 ) 186 Side Board ( Fd-241 / 371 ) 187 Table Centre Fd-274 / 375 ) 188 Table 900 X 900Mm Fd-291 189 Almirah Mess Utencils ( Fd-93 ( M ) 190 Book Case ( Fd-147 ) 191 Chair Dinning With Long Back Fd-357 ) 192 Hat Stand With Mirror ( Fd-Fd-233 / 361 / Fd-362 ) 193 Sofa Set 4 Seater ( Fd-281 / 373 ) 194 Sofa Set 5 Seater ( Fd-281 / 373 / Fd / Map-Ii / 02 ) 195 Sofa Set Single Seater ( Fd-281 / 373 ) 196 Stool Dressing Cb ( Fd-282 / 374 ) 197 Chair Dining For ( JcoS / OrS ) Fd / Map-Ii / 05 198 Table Wrting Folding ( Ce / Td-1139 / 97 ) 199 Schedule A Part-Ii Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Almirah Large Steel With Shelves ( Fd-351 / 1031 ) / Almirah Small / Medium Steel ( Fd-350 / 1032 / 243 ) / Locker Bedside Steel ( Fd-257 / 1029 ) , S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 200 Shutter ( Single Leaf ) For Almirah Large Steel Made Of 1.6 Mm Thick Ms Sheet And Shall Be Applied A Coat Of Red Oxide Primer On Both Sideafter Preparation Surfaces 201 All As Per Item 1 ( A ) Here-In-Before But For Almirah Small / Medium Steel 202 All As Per Item 1 ( A ) Here-In-Before But For Locker Bedside Steel 203 Shelves Made Of 1.25 Mm Thick Ms Sheet And Shall Be Applied A Coat Of Red Oxide Primer On Both Sideafter Preparation Surfaces 204 All As Per Item 1 ( D ) Here-In-Before But For Almirah Small / Medium Steel 205 All As Per Item 1 ( D ) Here-In-Before But For Locker Bedside Steel 206 Six Levers Brass Lock For Almirah Large Steel / Almirah Small / Med Steel Make : Godrej / Harrison / Link With Duplicate Keys 207 Three Way Locking Device Foralmirah Large Steel Of 10 Mm Dia Ms Rod As Per Trade Pattern Incl A Coat Of Red Oxide Primer 208 All As Per Item 1 ( H ) Here-In-Before But For Almirah Small / Medium Steel 209 Chromium Plated Steel Handle 125Mm For Almirah Large Steel / Almirah Small / Med 210 Chromium Plated Ms Key Plate Fixed With Screw And Nuts For Almirah Large Steel / Almirah Small / Med 211 Chromium Plated 100Mm Steel Handle D Type For Locker Bedside Steel 212 Leg For Almirah Large Steel / Almirah Small / Med Steel Made Of 1.6 Mm Thick Ms Sheet With Gas Welding Incl A Coat Of Red Oxide Primer 213 All As Per Item 1 ( H ) Here-In-Before But 1.0 Mm Thick Ms Sheet For Locker Bedside Steel 214 75Mm Chromium Plated Haps & Stapple Fixed With Rivets Of Locker Steel 215 Hanging Rod For Locker Bed Side Steeel Of 1.6Mm Thick Chromium Plated Ms Rod 216 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingtable Dining OrS ( Fd-165 ( M ) ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 217 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Not Less Than 250Mm Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Andpiece Will Be Counted As One. 218 Top Of 18 / 19 Mm Thick Block Board Of Size 1900 Mm X 685 Mm Covered With Aluminium Sheet 22 Guage On Top Complete All As Specified , As Directed And Shown On Drawing. 219 Rubber Shoe To Legs 220 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Chair Cb Steel With Arms / Without Arms ( Fd-75 ( M ) ) ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 221 Seat Frame Of Chair Cb Steel With Arms Of 1St Class Hard Wood Duly Polished With High Class Black Polish Incl Weaving With 2 Mm Wide Half Round Plastic Cane With Godrej Pattern & Border With 3 Mm Wide Plastic Cane Superior Quality As Shown In Drawing 222 All As Per Item No 3 ( A ) Here-In-Before But Back Frame 223 All As Per Item No 3 ( A ) Here-In-Before But Seat Frame For Chair Cb Steel Without Arms 224 All As Per Item No 3 ( C ) Here-In-Before But Back Frame 225 Arms Rest For Chair Cb Steel With Arms Of 1St Class Hard Wood Duly Polished With High Class Black Polish 226 Pvc Cap At Top Of The Frame Of The Chair ( 02 Nos To Each Chair ) 227 Pvc Shoe At Bottom Of The Frame Of The Chairs ( 04 Nos To Each Chair ) 228 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Table Office Clerk / Typist Steel ( Fd-84 ( M ) / 1004 / Fd-1006 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 229 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 230 Drawer Made Of 22 Gauge Ms Sheet With A Coat Of Red Oxide Primer 231 Six Levers Lock Of Godrej / Harrison With Duplicate Keys. 232 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Not Less Than 250Mm Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Andpiece Will Be Counted As One. 233 Pvc Shoe At Bottom Of The Leg Of The Table 234 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Table Office Officer Steel ( Fd-84 ( M ) / 1003 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 235 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 236 Drawer Made Of 22 Gauge Ms Sheet With A Coat Of Red Oxide Primer 237 Six Levers Lock Of Godrej / Harrison With Duplicate Keys. 238 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Not Less Than 250Mm Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Andpiece Will Be Counted As One. 239 Pvc Shoe At Bottom Of The Leg Of The Table 240 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Table 3 X 2 Steel With Drawer ( Fd-283 / 1008 ) / Table For Hav & Or Steel ( Fd-223 / 1007 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 241 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 242 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Not Less Than 250Mm Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Andpiece Will Be Counted As One. 243 Drawer Made Of 22 Gauge Ms Sheet With A Coat Of Red Oxide Primer 244 Pvc Shoe At Bottom Of The Leg Of The Table 245 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingtable 3 X 3 Steel ( Fd-291 / 1009 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 246 Top Made Of 18 / 19Mm Thick Both Side Prelaminated Mdf Board Having Surface Colour As Approved By Engineer-In-Charge.Sides Of The Mdf Board Shall Be Fixed With Pvc Edge Band Tape Duly Matched The Colour With The Board All As Directed. 247 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Not Less Than 250Mm Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Andpiece Will Be Counted As One. 248 Pvc Shoe At Bottom Of The Leg Of The Table 249 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingcharpoy Ip With Plytop ( Fd / Map-Ii / 01 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 250 12Mm Thick Ply Wood Top Bwr Grade Isi Marked Of Size 1950Mm X 900Mm ( Single Piece ) With Ms Nuts & Screws. 251 Pvc Shoe At Bottom Of The Leg Of The Charpoy 252 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingcharpoy Gi Pipe With Plytop: ( Fd-220 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 253 3 Way Galvanized Iron Elbow 32 Mm Dia.Note Weight Of Each Elbow Shall Not Be Less Than 450 Grams 254 Galvanized Iron Check Nut 32 Mm Dia.Note :- Weight Of Each Check Nut Shall Not Be Less Than 125 Grams 255 Long Rail Of 32 Mm Dia Galvanized Iron Pipe Medium Grade Incl Threading At Both Ends As Directed 256 Short Rail Converted Out Of Retrieved Long Rail, Item No 34 ( C ) Above Incl Cutting, Threading As Required And Directed 257 Leg Converted Out Of Retrieved Short Rail, Item No 34 ( D ) Above Incl Cutting, Threading As Required And And Directed 258 Provn Of Two Nos Ms Cleat As Shown On Drg To Hold The Mnf Set And One Ms Plate At The Bottom To Each Leg Converted Out Of Retrieved Short Rail 259 12Mm Thick Ply Wood Top Bwr Grade Isi Marked Of Size 1950Mm X 900Mm ( Single Piece ) . 260 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingfoam With Out Back ( Fd-77 ( M ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 261 Removal Of Old U / S Plank Of Form With Out Back And S&F New Plank Of Form Without Back Of Size 1525Mm X 255Mm X 25Mm Made Out Of 1St Class Hard Wood ( Teak Wood ) Including Applying Two Coats Of French Polish Complete And Fixed To Steel / Iron Frame With Suitable Gi Nuts ( 09 Nos ) And All Steel / Iron Surface Shall Be Paintedwith Two Coats Of Black Enamel Paint Over Two Coat Of Primer Complete All As Specified And Directed By Engr -In Charge. 262 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame And Replace With 25Mm Dia 1.6Mm Wall Thickness Ms Tube In One Piece Duly Welding To Bring Into Original Size As Per Drawing, Applying Of Red Oxide Primer After Preparation Of Surface.Upto 300Mm Long Piece Will Be Counted As One. 263 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingbench Workshop Steel ( Fd-1024 ) ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 264 40Mm Thick Top Made Out Of 2Nd Class Hard Wood With Three Coats Of Oil Paints Complete All As Specified And Directed. 265 Drawer Made Of 1 Mm Thich Ms Sheet With Coat Of Red Oxide Primer Including Preparation Of New Steel Surfaces Complete All As Specified 266 Cutting Down Wornout Portion Of Ms Tube Of The Steel Frame ( Each Upto300mm Will Be Caounted As One ) And Replace With 32 X 32 Mm Sq Tube Made Of 16 Gauge Pbi Sheet Fixed By Gas Welding Incl Painting With A Cot Of Red Oxide Primer Including Preparation Of New Steel Surfaces Complete All As Specified. 267 Pvc Shoes At The Bottom Of Leg. 268 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Chair Writing Map ( Fd / E6 / Map / 12 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 269 Replacement Of Exising Tapestry Of Seat Frame With Newtapestry Cloth Of Seat Frame Approved By Engr-In-Charge With Pvc Liping All Round Complete All As Specified And Directed By Engr -In Charge Note- Cost Of Tapestry Not Less Than Rs 200 / Rm. 270 All As Per Item No 36 ( A ) Above But For Back Frame 271 Hand Rest One Piece Made Of Black Integral Skin, Reinforced With Ms Insert It. Hand Rest Have Slope Towards Front As Specified 272 Replacement Of Complete Seat And Back With New Moulded Foam Cushioned 40Mm Density As Shape And Size, Covered With Tapestry Cloth As Approved Along With Pvc Liping All Round, Complete All As Specified 273 Rubber Stopper At The Bottom Of Leg. 274 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Chair School With Hand Board ( Fd / E6 / Map / 05 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 275 Hand Board Of 18 Mm Pre-Laminated Mdf Board Exterior Grade With 2Mm Pvc Edging & Screwed At Right Hand Side Of Chair Arm Fixed To Frame As Shown On Drawing. 276 Seat & Back In One Piece Made Of Pvc And Fixed With Frame 277 Pvc Shoe At Bottom Of The Leg 278 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Bed Hard Steel ( Fd / E6 / Map / 08 ( R ) ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 279 12Mm Thick Ply Wood Top Of Size 1950Mm X 900Mm ( Single Piece ) Bwr Grade Isi Mark With Ms Screws, Complete All As Specified 280 18Mm Thick Prelaminated Particle Board At Head Side Of The Bed As Specified 281 18Mm Thick Prelaminated Particle Board At Foot Side Of The Bed As Specified 282 Pvc Shoes At The Bottom Of Leg. 283 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Chair Computer ( Fd / E6 / Map / 01 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 284 Replacement Of Complete Seat With New Moulded Foam Cushioned 40Mm Density As Shape And Size Covered With Tapestry Cloth As Approved Along With Pvc Liping All Round, Complete All As Specified 285 All As Per Item No 40 ( A ) Here-In-Before But For Back Frame 286 Hand Rest One Piece Made Of Black Integral Skin, Reinforced With Ms Insert It. Hand Rest Have Slope Towards Front As Specified 287 Pedestal Assembly Complete 288 Twin Wheel Coasters Press Fitted At The Bottom Of Leg. 289 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingtable Computer ( Fd / E6 / Map / 03 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 290 Top Of 18Mm Thick Pre-Laminated Mdf Board Incl Pvc Lipping All Around The Top 291 Drawer Of 18 Mm Thick Pre-Laminated Mdf Board Fixed With Telescopic Channel 292 Shelf For Keyboardof 18 Mm Thick Pre-Laminated Mdf Board Fixed With Telescopic Channel . 293 Pvc Shoes At The Bottom Of Leg. 294 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Followingrack Shoe Steel ( Fd / E6 / Map / 02® ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 295 Ms Pipe Of 25Mm Dia For Leg Frame By Welding 296 Ms Jali As Shown On Drawing 297 Steelfurniture : Taking Down Worned Out / Unsv Components Of The Following Chair Verandah ( Fd-256, 259, 359 ) S&F New Component As Per Shape And Size Specified On Respective Drawings And As Directed By Engineer-In-Charge 298 Taking Out Old U / S Cane / Newar And Rubber Shoes From Chair Verandah, Removing Of Foreign Materials From The Iron Frame By Rubbing With Sand Paper, Painting Two Coats With White Synthetic Enamel Paintand Recanning Seat And Back With 4 Mm Wide Half Round White Plastic Cane Of Superior Quality As Directed By Engineer-In-Charge 299 Pvc / Rubber Shoes As Per Sample Approved 300 Schedule A Part-Ii Steelfurniture :Painting Of The Following Furniture Items With Two Coat Of Synthetic Enamel Paint ( Colour As Approved And Directed By Engineer-In-Charge ) After Preparation Of Surfaces :- 301 Almirah Steel Large With Shelves, Fd-351 / 1031 302 Almirah Small / Medium Steel ( Fd-350 / 1032 / 243 ) 303 Locker Bedside Steel ( Fd-257 / 1029 ) 304 Table Dining Or ( Fd-165 ( M ) 305 Chair Cb Steel With Arms / Without Arms ( Fd-75 ( M ) ) 306 Table Office Ckerk Steel ( Fd-84 ( M ) / 1004 ) 307 Table For Hav & Or Steel ( Fd-223 / 1007 ) 308 Table ( 900X600x760 ) Mm Steel With Drawer ( Fd-283 / 1008 309 Table 3X3 Steel ( Fd-291 / 1009 ) 310 Table Officer Officer Steel 311 Almirah Glazed Steel ( Large ) ( Fd-104 ) 312 Almirah Steel Large With 1 / 2 Hanging 1 / 2 Shelves With Side Mirror ( Fd-114 ( M ) 313 Book Shelf Open Steel Large ( Fd-69 ( M ) 314 Book Shelf Open Steel Small ( Fd-69 ( M ) 315 Charpoy Ip With Plytop ( Fd / Map-Ii / 01 ) 316 Form Wihout Back Steel ( Fd-77 / 1027 ) 317 Rack ( 1830X760x900 ) Mm ( Fd-129 ( M ) 318 Rack Adjustable ( Fd-106 ( M ) 319 Rack Steel 6 Tier Fd-345 / Fd-1038 320 Rack Side Steel With Tray, Fd-97 / 1023 321 Bench Wksp Steel ( Fd-1024 ) 322 Chair Writing Map ( Fd / E6 / Map / 12 323 Chair School With Hard Board Fd / E6 / Map / 05 324 Bed Hardfd / E6 / Map / 08® 325 Table Computer Fd / E6 / Map / 03 326 Rack Shoe Steel Fd / E6 / Map / 02®

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	12-09-2022	corrigendum	BOQ	21-09-2022
2	21-09-2022	Bid Auto Extn Corrigendum	Bid Auto Extn Corrigendum	28-09-2022

INR 500 /-

INR 84000.0 /-

INR 42 Lakhs /-