Procurement Of Wet System Spares Procurement Of Wet System Spares , Ba Hopper Feed Gate Assembly,Gate Face Liner For Bahfg Ahp U#3 Gate Face For Bottom Ash Hopper Feed Gate Assembly, Part No.:5&6, Qty:1Set (1Set=1 No Of Gate Wear Liner Moc: Ss-316 And Face Plate With Ms Back Up Plate Part No.6), Drawing No: Btps-Eeahp2-Ba-Fg-01, Make: Dcips/Umhs/Br Enterprises / Equivalent.,Ash Sluice Gate For Bahfg Ahp U#3 Ash Sluice Gate Of 36X36 For Bottom Ash Hopper Feed Gate Assembly , Part No.:9, Material: Ci, Fg-260, Is:210, Drawing No: Btps-Eeahp2-Ba-Fg-01, Make: Dcips/Umhs/Br Enterprises / Equivalent.,Sp Ring For Ba Hopper Fg Ahp U#3 Sp Ring For Ba Hopper Feed Gate U#3, Drawing No: Btps-Eeahp2-Bah-01, Make: Dcips/Umhs/Br Enterprises / Equivalent.,Inspection Window Glass For Ba,Inspection Window Glass (100Mm Dia),Assy.Of Ash Crusher (Clinker Grinder) U-3 Assy.Of Ash Crusher (Clinker Grinder), Type: Single Roll Reversible, Speed: 17 Rpm(Approximate), Max.Output Of Clinker : 25Mm, Speed Reduction Through Gearbox = 20:1, Speed Reduction Through Chain & Sprocket =2.8 :1 (Approximate), Capacity: 105 Ton/Hr, Moc: As Per Drawing No: Btps-Eeahp2-Cg-01,Shaft Sleeve Aca,Lantern Ring Aca,Gland Aca,Feeder Ejector Assembly Feeder Ejector Complete Assembly For Aph/Eco Hoppers U#3, Dry Ash Capacity : 4.25 Ton/Hr, Water Quantity And Pressure-160 Cu.M/Hr And 7 Kg/Cm2, Testing As Per Approved Qap, Slurry Concentration : 21.37 %, Mco: Inlet Elbow-Durite Bhn-450, Cover Plate: M.S.Is:2062, Water Chamber:C.I-Fg 260, Bhn:180, Water Chamber Liner: Durite Bhn-450, Nozzle:Ss 410, Nozzle Insert: Ceramic Hardness 8 Moh, Tailpiece:Durite Bhn-450, Hand Hole Cover For Tail Piece: Durite Bhn 350, With Required Necessary Fastners, Note: Agency Has Supplied As Per Dcips Drawing No: 11P01-1B-T-443. Make: Globus/Umhs/Dcips/Equivalent.,Jet Pulsion Pump Complete Assembly Jet Pulsion Pump Complete Assembly For Ahp U#3, Tech Specification, Capacity:85Tph, Moc, 1) Throat Cum Discharge Pipe- 24% Chromium Ci (Harness Min 550Bhn) Part No: 1. 2) Nozzle Tip: Ceramic Lined Ss/ Tungsten Carbide With Hardness Of Min 500Bhn, 3)Nozzle Inlet: F.G 260,Is:210, 4) Gasket: Rubber Asbestos, 5) Body: 24% Chromium Ci (Harness Min 550Bhn) Part No:9. 6) Aliging Ring: Steel , 7) Nozzle Inert: Ceramic Hardness 8Moh, 8) Flange Clamp Half: Steel, 8) Counter Flange: Ms As Per Is:2062, Note: Test Pressure Of Nozzle Inlet-15Kg/Cm2 And Throat Cum Discharge Pipe- 8Kg/Cm2, Drawing No: Btps-Eeahp2-Jp-01, Make: Dcips/Umhs/Br Enterprises/Equivalent.,Inlet Elbow For Feeder Ejector,Tail Piece For Feeder Ejector,Jet Pump Tail Pipe Jpp,200X600mm Wear Piece
