Providing, Installation, Testing And Commissioning Of Pumping Machinery Along With Allied Electro-Mech Equipment At Filtration Plant Seri Sayal Base.= 1 Providing And Installation Of Monosub Pump Set 5000 Gph X 40Mh Coupled With Suitable Motor. The, rajouri-Jammu And Kashmir

Providing, Installation, Testing And Commissioning Of Pumping Machinery Along With Allied Electro-Mech Equipment At Filtration Plant Seri Sayal Base.= 1 Providing And Installation Of Monosub Pump Set 5000 Gph X 40Mh Coupled With Suitable Motor. The Pumping Machinery Should Confirm To Relevant Iso With All Latest Amendments. The Equipment Shall Also Be Accompanied With Test Certificates And Performance Curves. Installation Of Monosub 5000Gph X 30Mh Along With Allied Electromechanical Equipment By Way Of Fabrication Of 80Mm Dia Gi Column Pipe 10Ft Long Welded With Ms Flanges-80Mm Dia At Both Ends-02Nos, For Making Delivery Of The Pump. Fabrication Of Gi Pipe Nipple With Threads At One End & Ms Flange At Other End & Fastening The Threaded End Of Nipple With The Delivery Of Pump.Fabrication Of Ms Clamps 80Mm Dia. - 02 Nos. Each For Holding Monosub Pump & Column Pipes. Fabrication / Fitting Of Bed Plate For Resting Of Clamps For Holding Monosub Pump & Nipples. Coupling Of Pump Motor With The Help Of Coupling Pulley. Providing / Fitting Automatic Control Panel Of Suitable Capacity And 4Mm Square Submersible Cable -50 Mtr ( Approx ) For Making Of Connection From Submersible Control Panel To Motor With Proper Thimbling And Insulation. Providing / Fitting Of Chain Pulley Block Of Capacity -01Ton Heavy Duty Of Isi Make. Lowering Of Monosub Along With Gi Pipe Nipples Into The Well With The Help Of Chain Pulley Block, Ropes & Skilled / Unskilled Labours. Providing / Fitting Of Ms Bends 80Mm Dia. With Ms Flanges. Providing / Fitting Of 80Mm Dia Check Valve -01No With Ms Flanges, Nut / Bolts & Washers, And Interconnecting With The Raising Main With All Allied Welding Work. The Job Also Includes Providing / Erection Of Steel Tubular Pole Of 8Mtr Long – 03No For Extension Of Lt Network From Pump Room To Percolation Well ( Intake ) . Providing / Stringing Of Conductor Wire All In Tpn - 1.0Km Approx. Providing / Fitting Of U-Clamps, Shackle, Pin Insulator, Nut Bolts And Allied Material Required For Completion Of Work At Site. Complete Job Includes Cost Material Such As Pumping Machinery, Labour Charges, Carriage Charges And Welding Charges Etc Required At Site Of Work. 2 Providing, Installation Of Horizontal Centrifugal Pump Set 5000 Gph X 250Mh Coupled With Suitable Motor At Filtration Plant Seri Sayal. The Pumping Machinery Should Confirm Relevant Iso With All Latest Amendments. Installation By Way Of Laying Of Foundation Block Of Size 2Mtr X 1 Mtr X 1Mtr Depth Inside The Pump Room By Way Of Excavation Of Floor And Disposal Of The Excavated Earth By Using Manual Labour Outside The Premises. Cleaning And Levelling Of Excavated Trench. Laying Of Foundation Block Of Rcc For Installation Of Hcp 5000 Gph X 250 Mh. The Job Includes Fabrication, Welding And Laying Of Steel Mesh Made From 12Mm Tor Steel Placed Horizontally, Vertically And Diagonally At Equal Distance Including Form Work. Laying Of Foundation Block Of Rcc In The Ratio 1:2:4 ( Cement, Sand And Bajri ) And Grouting Of Fabricated Foundation Bolts. The Entire Block To Be Laid In Such A Way That It Can Dump All Types Of Mechanical Vibration Created By Dynamic Load Of The Pump. Placing Of Base Frame And Levelling. Tightening Of Base Frame By Fastening Of 6 No. Foundation Bolts. Complete Job Includes Cost Of All Types Of Material Such As Cement, Sand, Bajri, Tor Steel, Foundation Bolts, Nuts, Washers, Bolts, Carriage Of Material To Site Of Work On H / L, Hire Charges Of Tools And Tackles, Labour Charges Of Skilled And Semi-Skilled Workers. Placing The Hc Pump Set And Motor On The Base Plate Tightening Of Foundation Bolts Of Pump And Motor Set Fixing Of Coupling Pulley On Drive End Side Of Pump And Motor Shaft With The Help Of Cotters And Coupling Bolts. Proper Leveling Of Pump Motor Set On The Base Frame By Way Of Providing Steel Shims And Checking The Alignment Of Pump Motor Set. Fabrication, Fitting And Laying Of 80 Mm Dia Suction Line From Service Reservoir Upto The Suction Of Hc Pump Set As Per Site Requirement By Way Of Cutting, Fitting Of 80 Mm Dia Flanges And Welding By Using Good Quality Electrodes So As To Get Leak Proof Joints. Fitting Of 80 Mm Diasluice Valves With Flanges, Bends Properly Welded As Per Site Requirement Which Is Required For Stopping The Flow Of Water In Suction Line For Maintenance Of Pump Set. Providing And Fixing Reducer Nipple With Flanges On Both Sides With Proper Bend To Be Fitted On The Suction Side Of The Hc Pump Sets. Fabrication, Fitting And Laying Of 80 Mm Dia Delivery Line For Hc Pump Sets. Fabrication And Fitting Of Expander Nipple On The Delivery Side Of Pump Set With Flanges On Both Sides To Be Connected With Delivery Side Of The Pump Set With Matching Holes On One Side And 80 Mm Dia Delivery Line On The Other Side. Providing And Welding 80Mm Dia Half Bends With Flanges On Both Sides As Per Site Requirement. Fitting Of 80 Mm Dia Sluice Valves And Reflux Valves-01 No Each With Nuts, Bolts And Gaskets With Proper Flanges On Both Sides. Extension Of The Delivery Line From Reflux Valve Upto The Common Manifold By Way Of Providing Bends Nipples Etc. As Per Site Condition. The Complete Welding Work On The Delivery Line Shall Be Done By Using Superior Quality Welding Electrodes So As To Avoid Any Air Gap And To Ensure Leak Proof Joints. The Delivery Lines Of Pump Set Shall Be Connected / Joined / Welded With The Rising Line. Complete Job Including Cost Of Material, Hire Charges Of Tools And Tackles. 3 Fabrication And Fitting / Grouting Of Angle Iron Panel Board Fitted With 12Mm Thick Water Proof Ply With Good Quality Mica. Providing / Fitting Of 200Amp 415V Hrc Type Main Switch ( H / Duty ) -01 No, Providing / Fitting Of 185Mm Square Aluminium Cable -20 Mtr-3.5 Core For Making Of Connection From Lt Fuse System To Main Switch With Proper Thimbling And Insulation. Providing / Fitting Of 200Amp Busbar On The Panel Board. Providing / Fitting Of Suitable Capacity Starter On The Panel Board. Providing / Fitting Of Suitable Capacity Of Copper Cable For Making Connection From Lt Control Panel To The Motors.Checking Continuity Of Whole Electric Circuit. 4 Fabrication / Manufacturing Of 100Kva Voltage Stabilizer At Oil Cooled Unbalance Type 415Volt At Base And Stage Ist Of Wss Seri Sayal, Complete With Transformer Oil In Copper Windings Capable Of Operating On Unbalanced Voltage. Installation, Testing & Commissioning Of 100Kva Voltage Stabilizers By Way Of Carriage / Shifting Of Stabilizer To Site Of Work On Mt And Hl. P / F Of Aluminium Cable 185Mm Sq Unarmoured-20Mtr Appox Of Standard Isi Make ( As Per Site Condition ) For Making Connectionsfrommainswitchto Voltagestabilizer For All The Threephasesin Threeleadswithneutral & Then From Stabilizer To Buss Bar Fuse Systemwith Properthimblingdulycrimpled By Usingcrimpling Tool& Proper Insulation. Filling Of Transformer Oil Up To Required Level After Heat Treatment / Dehydration To Make It Moisture Free. Job Includes Cost Of Material And Fitting Charges. Specification As Below Capacity: 100Kvaphase :03Make Confirming To Relevant Iso With All Latest Amendmentsinput Voltage : ( 160-380 ) Voltoutput Voltage:415 Volts+ / - 1% Type :Manually Operatedcorrection Rate :12 To 35 V / Secregulation:+ / - 1%Frequency : 48 To52 Hzcooling Method :Oil Cooledefficiency : 95%High & Low Cut Off : Installed With Standard Capacity By Pass Change Over Switch :Yesmccb:Heavy Dutysingle Phase Preventer :Yesmaterial Of Construction :The Core Should Be First Quality ( Crgo ) Silico Steel Core, Conducting Conductor Should Be Off 99.95% Of Electrolytic Copper Ms Steel Thickness Of Container 14 / 16 Swg. Transformer Oil To Be Used Shall Be Of Best Quality Conforming Of Is 335 With Latest Amendments.Voltage Stabilizer Shall Be Mounted On 02 Pairs Of H / D Ms Wheels For Making Shifting / Fixing Easy. Voltmeter / Ampere Meter Good Quality Isi Make Of Required Specification, Toggle Switch 03 No For Input / Output Reading Of Each Face Rotary Switches Of Suitable Amp Range Each Of 08Steps. Painting Shall Be Enameled Steel Grey / Green Colour. 5 Testing And Commissioning Of Hc Pump Motor Set With Stand By And All Other Allied Electro Mechanical Works. Checking Of All Electrical Connections, Tapping And Tightening All Other Connections. Plugging Of Leaking Joints If Any By Way Of Welding, Replacement Of Gaskets And Tightening Of Nuts And Bolts. Checking The Alignment Of Pump And Motor Sets And Testing The Machinery On Full Load. Complete Job

INR 250 /-

INR 28000.0 /-

INR 14 Lakhs /-