|
| 1 | work name |
| 2 | Demolishing cement concrete including disposal of material within 50 meters lead : 1 : 3 : 6 or richer mix. |
| 3 | Earth Work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50mtr. All kinds of soil Depth upto 1.5 m |
| 4 | Transportation of surplus excavated soil loading and unloading etc. complete with all lead and lift. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 6 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. : 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 7 | CROSS TRAINERProviding and fixing of Cross trainer of size 1320mm (Length) x 600mm (Width) x 1750mm. (Height) fabricated with the main frame Pipes of 80NB shall be made of “C” Class G.I and pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame shall be made up of 25NB “C” Class G.I. Pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipeof 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe should be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm and CRC square pipes of 3mm thickness.To build structure bushes to be used which shall be made from M.S.seamless pipe of 60mm OD with 5 mm thickness. The footrests shall be made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick.Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35mm, 25mm, and 17mm shall be made up from SAE 8620 bright . The Bearings shall be usedof “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. A16 , A 24 mm circlips shall be used for assembly. Bolt M8X16 mm and NY lock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 8 | THI-CHI SPINNER (2 WHEEL)Providing and fixing of Thi-Chi spinner (2 Wheel) of size 700mm (Length) x 1000mm (Width) x 1280mm (Height) fabricated with a center pipe of 100NB shall be made up of “C” Class G.I. pipe. The handle movement round frame shall be made up from 25 NB “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø 25 mm of SAE8620 bright material. The bearing shall be used of “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile S.S. nut bolts shall be used for assembly. Foundation cover Closing Cap shall be made from FRP Material with 0.7 mm thickness. The cerclips used for assembly shall be of of A24 and A11. The nylon bush shall be used for handle knob. The powder coating shall be done with pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 9 | SEATED PULLERProviding and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm & 10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 10 | SIT UP BOARD DOUBLEProviding and fixing of Sit up Board double of size 1760mm (Length) x 1140mm (Width) x 660mm (Height) fabricated with the main frame of 25mm NB shall be made from “C” Class GI pipe. FRP sheet of 3mm thickness shall be moulded on main frame. The remaining frame of the sit up board of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. The foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 11 | CHEST PRESSProviding and fixing of Chest Press of size 2000mm (Length) x 710mm (Width) x 2200mm. (Height) fabricated with the center pipe of 100NB shall be made up of “C” Class G.I. pipe. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes shall be made up from 25NB “C” class G.I. pipe. The handle frame shall be made up from 32NB “C” class G.I. pipe. To build structure bushes to be used which shall be made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall bemade up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap shall be made from FRP Material with 0.7 thickness. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 mm & A16mm. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. |
| 12 | POMMEL HORSEProviding and fixing of Pommel Horse of size 2150mm (Length) x 800mm (Width) x 800mm. (Height) fabricated with the main frame of 80NB and 50NBshall be made from “C” Class G.I. pipe. The handle frame of 32NB shall be made from “C” Class G.I. pipe. 40mm x 40mm CRC square pipes frame shall be placed on the 25mm x 25mm x3mm M.S. L Angle with 60 x 10m thickness flat should be used for support. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. |
| 13 | DOUBLE TWISTER STANDINGProviding and fixing of Double Twister Standing of size 1500mm (Length) x 600mm (Width) x 1300mm. (Height) fabricated with a Center Pipe of 100NBshall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The bottom frame of 32NB shall be made from “C” class G.I. pipe. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB”C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size Ø300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35 mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed. Brand. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 14 | SEATING & STANDING TWISTERProviding and fixing of Seating & Standing Twister of size 1700mm (Length) x 540mm (Width) x 1250mm. (Height) fabricated with a Center Pipe of 100mm NB shall be made from “C” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mmshould be provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister of 32 NB, 50 NB, and 25 NBshall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe of 25mm NB. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The Pins to be used which shall be made up of Ø 35 mm SAE 8620 bright material. The bearings shall be made of of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
