E-Quotation No.3 For 2022-23 E-Rate Quotation For Preparation Of Ssr For Verious Item Which Is Mention In Notice , Providing And Laying Of Rumble Strip Usingplastirib 2K 2 Component Cold Plastic Road Marking Material In Single Monolithic Application To Create Rumble Strip Raised Section 15 Mm - 20 Mm High , 200 To 300 Mm Wide And Spaced About 1 Meter Centre To Centre Of Roughly 6 Numbers At One Location, Across The Entire Carriageway. Each Rumble Marking Shall Be Made Complete With Drop On Solid Plus Reflective Glass Beads @ 350 Gm / Sqm Spread Throughout The Surface Of Marking. The Finished Surface Shall Be Levelled, Uniform , Free From Straks And Holes Including Surface Cleaning And Cost Of All Materials Etc. Complete. As Per Irc 99, These Rumble Strips Shall Be Applied As Traffic Calming Measure. , Kerb Stone / Vertical Surface Painting With Reflective Paint, Make Grade 1 ( As Per Is 164 ) Water Based Acrylic Paint, Preferably Mechnical Application For One Coat Priming Coat And 1 Uniform Retro Reflective Finish Coat In Required Colour. Yellow Retroreflecive Coat Shall Be Bright Yellow During Night With Minimum Rl ( Dry ) > 375 Mcd / M2 / Lux White Retroreflective Coat Shall Be Bright White During Night With Minium Rl ( Dry ) > 450 Mcd / M2 / Lux .Cleaning Of The Surface Thoroughly By Removing Flakes, Dust Deposits, Vegetation Growth, Pasted Paper Etc., Using Coir / Coil Brush, So As To Enable The Application Of Respective Primer Etc. , Providing And Applying 2 Component Cold Plastic Night Glow Paint Rolled On Surfacing Material Solvent Free, High Build Two Pack Seamless, Tough, Skid Resistant, Material Which Has Property Of Attaining 600 Microns Thickness In Single Coat Application White ( Or As Required Colour ) Based On Glass And Colour Retaining Acralic Cross Linking Resin System For Coloured Road Surfacing Including Surface Cleaning And Cost Of All Material Etc. Complete. ( All Inclusive On Bitumen Or Concrete Surface ) Night Glow Paint Shall Preferably Be Roller Applied. After Glow Finish Surface Shall Provide Minimum Of 8 Hrs Glow After Fully Absorbing Ambient Light ( Visibile Light Or Uv Light ) For 15 - 30 Min. Cleaning Of The Surface Thoroughly By Removing Flakes, Dust Deposits, Vegetation Growth, Pasted Paper Etc., Using Coir / Coil Brush, So As To Enable The Application Of Respective Primer Etc. , Augmented Wet Reflective Dot ( Awrd ) Marking System On Awrd On - Bituminous Surface Of Special 2 Component Cold Plastic Road Marking Primer Supply And Application Awrd Road Marking System With Minimum Of 50% Of The Intended Road Marking The Surface Area To Be Covered With Dots Of Thickness Of 5+1 Mm, Each Dot Having Dia. Of 25 + 5 Mm Using Plastidot 2K 2 Component Cold Plastic Road Marking Material And Solid Plus 100 Drop Of Glass Beads With Ri 1.6. Performance Parameters Shall Comply With Rl Dry > 800 Mcd / Sqm / Lux & Rl Wet > 250 Mcd / Sqm / Lux , Measured Using Zehntner Gmbh / Esylux / Delta Make Reflectometer In Case Of Concrete / Worn Out Bituminous Surfaces Application Of 2 Component Cold Plastic Road Marking Primer Is Mandatory. , Augmented Wet Reflective Dot ( Awrd ) Marking System On Awrd On- Concrete Surface With Application Of Special 2 Component Cold Plastic Road Marking Primer Supply And Application Awrd Road Marking System With Minimum Of 50% Of The Intended Road Marking The Surface Area To Be Covered With Dots Of Thickness Of 5+1 Mm, Each Dot Having Dia. Of 25 + 5 Mm Using Plastidot 2K 2 Component Cold Plastic Road Marking Material And Solid Plus 100 Drop Of Glass Beads With Ri 1.6. Performance Parameters Shall Comply With Rl Dry > 800 Mcd / Sqm / Lux & Rl Wet > 250 Mcd / Sqm / Lux , Measured Using Zehntner Gmbh / Esylux / Delta Make Reflectometer In Case Of Concrete / Worn Out Bituminous Surfaces Application Of 2 Component Cold Plastic Road Marking Primer Is Mandatory. , Supplying And Fixing Of High Performance Moulded Shank Raised Pavement Marker / Cats Eye Made Of Reinforced Polycarbonate And Weather Protected Ip > 68 Abs Moulded Body Having 2 Compartment Scratch And Abrasion-Proof Prismatic Polycarbonate Lens Capable Of Providing A Total Internal Reflection Of The Light Entering The Lens Face And Shall Support A Load Per Wheel ( Per Axle ) Of 20000 Kg And Per Axle 40000 Kg Tested In Accordance To Astm 4280D & En 1463-1 And En 1463-2 And Morth. The Dimensions Of The Pavement Marker Being 100 X 100 X 18 Mm And Weight 140Gm, Pin 55 Mm Depth Dia 13 Mm In Star Shape For Better Gripfixing Will Be By Drilling Holes On The Road For The Shank To Go Inside, Without Nails And Using Cold Plastic-Based Adhesive As Per Manufacturers Recommendation And Complete As Directed By The Engineer. The Contractor And Manufacturer Shall Submit A Minimum 1 Yr Installation Warranty And 2 Years Reflectivity Warranty For Satisfactory Field Performance. , Supplying And Fixing Of Solar Road Studs ( High Performance ) Polycarbonate Body, Pavement Surface Mounted Compliant Withen1463 Part 3 Havinguni-Direction Or Bi-Directional With Solar Powered Led Illumination And Reflective Panel Having 1 ) Dimensions 115 X 100 X 8.5 Mm 2 ) Marker Shall Support A Load Of 20 Ton Tested In Accordance To En 1463 . 3 ) Waterproof And Dust Protection Ip > 68 4 ) Weight 117 Gram 5 ) Fixing Using 2 Coponent Cold Plastic Based Adhesive / Butyl Tape Or As Reccomended By Manufacturer 6 ) Working Temperature: Up To 80 Deg. C 7 ) The Contractor And Manufacturer Shall Submit A Technical Warraty Of 1 Yr. , Providing And Fixing 8 Mm Tinted Tuffan Glass With Fitting Inaluminium Section Of Size 100 Mm X 763 Mm Also Including Door Glass With Ss Handle Of Size 1.2M Height And 50Mm O.D. And 30Mm I.D. And Ss Door Hinges Of Size 150Mm Height And 80Mm Width On One Face, Fitting Glass With Silicone Tube Including Scaffolding And Fitting Charges Etc. Complete & As Directed By Enginner Incharge , Providing Concrete Resurfacing System Of High Strength High Abrasion Resistant Deck Crs Base Coat And Deck Crs Top Coat Of Approved Color With Antiskid / Rough Texture And With Approved Stencil Pattern Following By Deck Sealer Final Coat, Including Providing Surface Preparation By Using Grinder Machine / Hand Grinders On Serrated / Slurried Concrete Surface To Expose Original Hard Concrete Surface And Washing Area Thoroughly Including Removal Of Nails Erc Complete. Surface Will Be Open To Traffic After 72 Hours Of Application Of Deck Crs. Deck Crs Consumption 3.8-4 Kg / Sqm , Providing Concrete Resurfacing System Of High Strength High Abrasion Resistant Deck Crs Base Coat And Deck Crs Top Coat Of Approved Color With Antiskid / Rough Texture Without Any Pattern ( Plain ) And Followed By Deck Sealer Final Coat, Including Providing Surface Preparation By Using Grinder Machine / Hand Grinders On Serrated / Slurried Concrete Surface To Expose Original Hard Concrete Surface And Washing Area Thoroughly Including Removal Of Nails Erc Complete. Surface Will Be Open To Traffic After 72 Hours Of Application Of Deck Crs. Deck Crs Consumption 3.8-4 Kg / Sqm
