|
| 1 | SUB HEAD - I Pumps & MotorsPreventive Maintenance of the fire as per Pump List Attached. The agency will undertake the maintenance work of the pumps only through the OEM or OEM authorized dealer. |
| 2 | Site, Model, Make, Primer Mover & Qty of Pumps |
| 3 | OLD MAGZINE -UP150/45(KBL)- Engine driven - 01 Nos UP150/45(KBL)- Motor driven - 02 Nos CPHM40/26(KBL)- Motor driven - 01 Nos |
| 4 | NIRANJAN AUDITORIUMDSM80/36(KBL)- Engine driven -01 NosDSM80/36(KBL)-Motor driven - 02NosDB32/26(KBL)-Motor driven -01 NosDB50/16(KBL)-Motor driven -02 Nos |
| 5 | NEW BUILDING DSM100/36(KBL)- Engine driven -01 NosDSM125/40(KBL)-Motor driven - 01NosRKB40/12L5(KBL)-Motor driven -01 Nos |
| 6 | NAGRANI BK DB50/16(KBL)-Motor driven -02 Nos |
| 7 | Total(Pumps) - 15 Nos |
| 8 | Scope of work covered under the preventive maintenece |
| 9 | One visit in each three months will be made by an OEM (KBL) service person with priorintimation. |
| 10 | Twobreakdown visits included under AMC. |
| 11 | Complete check-up of the Pump sets as per KBL standards. |
| 12 | Check free rotation of pumps. |
| 13 | Check tightness of casing bolts, Foundation bolts, and Grease MS Fasteners. |
| 14 | Oil levels, grease in bearings, Condition of bearing to be checked and replenished if required(Spare shall be provided by deptt) |
| 15 | Vibration, Noise, Bearing Temperature, Voltage, Speed and pressure to be measured and recorded. |
| 16 | Alignment of pump set to be checked and in case if required rectification to be carried out and readings to be recorded. |
| 17 | Coupling bushes, pins, rubber parts to be checked and to be replaced if required.(Spare shall be provided by deptt) |
| 18 | Mechanical seal condition to be checked and suitable recommendations to be made. |
| 19 | Service report will be generated afterevery visit recording data anddetails of above checks. |
| 20 | Training will be provided to site operators to obtain optimum output & lifeof equipment. |
| 21 | Overhaulingof the following Pump including Dismentaling, Machining , Oiling , Greasing , Assembling & Installation at Site includingloading and unloading,to and fro transportation ofpump from NSG Campus Manesar to the workshop. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. Model & Make. |
| 22 | UP150/45 or DSM80/36 or RKB40/12L5.KBL make |
| 23 | CPHM40/26.KBL make |
| 24 | DB32/26 or DB50/16.KBL make |
| 25 | DSM100/36 or DSM125/40.KBL make |
| 26 | Replacement of the following spare parts of the existing KBL Pump UP150/45 \"Kirloskar\" make main fire pump driven by electric motor 90KW/120HP capacitywith a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. Thework of the pumps will be done only through the OEM or OEM authorized dealer. |
| 27 | Mechanical Seal |
| 28 | Mechanical seal Plate |
| 29 | Sleeve MOC-Bronze (17458CQ001012) |
| 30 | set of Gasket MOC- Non asbestos |
| 31 | O- ring MOC- Natural Rubber |
| 32 | Ball Bearing 2877 MOC-SS (X630900400000) |
| 33 | Wear Ring MOC-Bronze(1712021991012) |
| 34 | Rewinding of (from 12.5 HP up to 120 H.P. three-phase capacity) electrical motors including all necessary material and of the same characteristics as original with required size of super enameled copper wire and F class insulation material including dismantling, removing of burnt wires, cleaning of slots, varnishing, assembling, greasing, testing etc. complete as required including credit for old scrap material which will be retained by the contractor etc., complete as required. Thework of rewinding of motors will be done only through the OEM or OEM authorized dealer. |
| 35 | SUB HEAD - IIFIRE ALARM SYSTEM SITC/Replacement of addressable Manual Call Point Complete as required through authorised dealer or OEM( Compatible With EST3 or equivalent Addressable System ) Make- Edward/Apollo/Siemens/Notifier or equivalent |
| 36 | SITC/ of addressable photo thermal detector complete with mounting base complete as read-through authorised dealer or OEM ( Compatible With EST3 or equivalent Addressable System ) Make- Edward/Apollo/Siemens/Notifier or equivalent |
| 37 | SITC of intelligent addressable programmable sounder complete as required through authorised dealer or OEM( Compatible With EST3 or equivlent Addressable System )Make- Edward/Apollo/Siemens/Notifier or equivalent |
| 38 | SITC of addressable fire control module complete as requiredthrough authorised dealer or OEM( Compatible With EST3 or equivlent Addressable System ) Make- Edward/Apollo/Siemens/Notifier or equivqlent |
| 39 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinkler of rating 68 degree centigrade with required accessories(Pendant/upright sprinkler) |
| 40 | SITC of horn cum Strobe Complete as read-through Authorised dealer or OEM .( Compatible With EST3 or equivalent Addressable System )Make- Edward/Apollo/Siemens/Notifier or equivalent |
| 41 | SITC of wall speaker 1.5/3/6 W Metal Box ceiling /wall speaker complete etc. as required Make - Honeywell/Bosch/Ahuja or equivalent |
| 42 | Dismantling , Cleaning & Re-fixing intelligence detector , hooter , MCP & RIincluding checking, testing and connection etc. as required. |
| 43 | Supply installation testing commissioning of SMPS device compatible with two loop firepanel make Est3 or equivalent as per direction of engg in charge . |
| 44 | Servicing , Commissioning and reprogramming of existed addressable fire alarm panelcompatible with EST3 etc. complete as required. |
| 45 | SITC of Protective cover locked with plastic tie /metallic wire suitable for addressable manual call pointincluding dismantling & re-fixing MCP with necessary arrangements as per direction of engineer in charge Make- Hensel KG9001 /Honeywell or equivalent as approved by Engg in charge . |
| 46 | SUB HEAD III - PIPES & ASSECORIES Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :300mm |
| 47 | Dismantling and reinstalling the existing 150 mm non-return valve in horizontal alignment in the FBC pipeline, as well as providingadditional quantity of 150 mm \"C\" class heavy duty MS pipeconforming to IS 3589/IS 1239, including welding, fittings such as elbows, flanges, nuts, bolts, gaskets, etc., whichever are required to complete the work, painting with two or more coats of synthetic enamel paint on the pipe of the required shade, testing and commissioning, etc., as required. |
| 48 | Providing, installation, testing & commissioning of water curtain nozzle 15/20 mm dia nickel chrome plated brass, BSPT, K-factor as per design consideration complete as required |
| 49 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling or on pipe with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm Dia |
| 50 | Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm diainstantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required |
| 51 | Single Headed Gunmetal |
| 52 | Supplying, fixing, testing and commissioning of butterflyvalve of PN 1.6 rating with bronze /gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : |
| 53 | 80mm |
| 54 | 100mm |
| 55 | 150mm |
| 56 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 57 | Supplying & replacement of weather proof hose cabinet suitable for external hydrant/FBIC fabricated out of 2 mm thick MS Sheet with 6 mm thick glazed glass door in front having locking arrangement having provision for 02 Nos RRL hose Pipes & 01 Nos Nozzlemounted on wall or raise brick platform & duly painted with PO redexternally & white internally with synthetic enamelled paint ,sign writingetc. complete in all respect as required at site& having min dimension - 900mm x 600mm x 500mm deep . |
| 58 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gunmetal Make - Newage/Safex/Safegaurd/Essel/Lifegaurd |
| 59 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. Make Denfoss/Indfos/Sitzer |
| 60 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc. as required. 150 mm diaMakeDenfoss/Indfos/Sitzer |
| 61 | Supplying and fixing undermentioned Item in existingDrum & Bracket arrangementcomplete connection etc. asrequired |
| 62 | Water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585Size - 20 mm nominal internal dia x 30 Mtr Length including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 63 | 20 mm nominal internal dia gun metal globe valve with nozzle on existing water hose with SS clampincluding credit for existing gun metal globe valve & nozzle material which will be retained by the contractor etc., complete as required. |
| 64 | Hose reel drum with brackets conforming to IS 884 MS construction spray painted in post office red including credit for exisitng reel drumwhich will be retained by the contractor. etc. complete as required. |
| 65 | Fabrication supply installation testing commissioning MScabinet made of 1.2mm thick MS sheet with4 mm thick transparent acrylic sheet double-leaf door on the front including necessary locking arrangement including mounting on wall, suitable to accommodate different typefire extinguisher duly painted with Post Office red externally and white internally with synthetic enamel paint without back cover including dismantling & refixing the existing fire extinguisher completely required as per direction of engineer-in-charge (min depth 250mm) as per site condition for a fire extinguisher as required. |
| 66 | Providing & fixing MSClamp suitable for existing fire extinguisher ( Dry Powder 06 kg / Water Spray 09 Ltr / CO2 type 4.5 Kg) |
| 67 | SUB HEAD IV - E &M WorkEarthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 68 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 69 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 70 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 71 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required |
| 72 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required |
| 73 | SITC of wall fan 400 mm sweep oscillating type having aerodynamically designed & balanced blade complete with all accessories such as front cover, mounting accessories i/c connection etc. as reqd.Havells Dzire 400 or Equivalent in Crompton/Usha |
| 74 | Wiring for submain wiring along with earth wire with following size of FRLS PVC insulated copper conductor single core cable in surface/ recess medium class PVC conduit as reqd |
| 75 | 2X1.5 Sqmm + 1X1.5 Sqmm earth wire |
| 76 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 77 | Providing and fixing following switch gears, meters and accessoriesin existing cubicle panel/starter board including drilling holes in cubicle panel, making connections, etc. as required including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 78 | 3Pole,415V , Power contactor AC3 rating 18 A |
| 79 | 3Pole,415V , Power contactor AC3 rating 25A |
| 80 | 3Pole,415V , Power contactor AC3 rating 32A |
| 81 | 3Pole,415V , Power contactor AC3 rating 70A |
| 82 | 3Pole,415V , Power contactor AC3 rating 110 A |
| 83 | Overload thermal relay MN2 L&T 9-15A |
| 84 | Overload thermal relay MN2 L&T 14-23A |
| 85 | Overload thermal relay MN5 L&T 66-110A |
| 86 | Add on Block 2NO+2NC |
| 87 | Add on Block 1NO+1NC |
| 88 | SUB HEAD V - FIRE FIGHTINGEQUIPMENTSSupply, Installation, Testing and Commissioning of UL Listed ABC MAP-90% (Mono Ammonium Phosphate) Automatic Ceiling Mounted Fire Extinguisher for Oil Charged Transformer Rooms, Capacity 10 Kg, Applicable Fire Classes A, B & C, UGTS Pressure Gauge, Brass Forged Sprinkler Valves with Nozzle and Equipped With Pressure Gauge, External Coating Pure Polyester and Internal Epoxy Polyester Powder Coated, Heat Sensitive Glass Bulb of 68°C. Make : FireMech / Ceasefire / Minimax/Kanex |
| 89 | Providing and fixing Dry powder ( Stored pressure) type portable fire extinguisher of following capacity with mono ammonium phosphate powder 90 % applicable to fire class A,B,C controllable discharge mechanism with EPDM Hose and nozzle, UGTS Pressure gauge, deep drawm with MIG welding technology , external pure polyester & internal epoxy polyester powder coated , brass forged valves with safety pin of SS Material and welding procedure approved by TPI rating as per 15683 and ISI Mark with suitable fixing bracket ( MS ) etc. as reqd .Make -Ceasefire/Minimax /Kanex |
| 90 | 6 Kg Powder Stored pressure type |
| 91 | Providing and fixing CO2 type (High pressure ) type portablefire extinguisher of following capacity with CO2 Gas foo fire class B & C electrical discharge controlmechanism fitted with high pressure steel braided discharge nozzle for dispersed discharge of CO2 enamel spray painting powder coated handle , hot spinning seamless ISI Marked rating as per IS 15683 with suitable fixing bracket (MS) etc. complete as reqd Make - Ceasefire/Minimax /Kanex |
| 92 | 4.5 Kg CO2 Portable fire extinguisher type |
| 93 | SUB HEADVI - Miscellaneous WorkSITCDiesel Engine Manual Start (Air Cooled) Driven Make Kirloskar TAF1/Greeves/Field Marshal(With STD Manual Starting) or equivalent flexiblly coupled with Self Priming Pump Kirloskar SP3L or equivalent in Crompton/Wilo ,suction- 80mm Delivery - 80mm mounted on movable trolley fabricated out of C Channel complete with solid wheel with Movable handle arrnagement & side open Canopy of MS Sheet. [Warranty -01 Year] |
| 94 | Supplying, installation, testing & commissioning of 600 KVA, 50 Hz, servo motor operated line voltage corrector, copper wound, indoor, continuous duty, three phase, suitable for 3 Phase Unbalanced /balanced input voltage and unbalanced/ balanced load conditions, which shall comprise three nos. fully IC controlled sensing circuits microprocessor based, with built-in filters to improve the output wave to be pure sinusoidal and control each phase individually. Conforming to IS 9815:1994 with input voltage 300-460V Output 415 (as set output voltage),+ -1%, naturally oil cooledwith first filling of transformer oiland necessary bypass arrangements, MS tank Enclosure mounted on Wheels, withDigital Display having facilities to show Fault Indication, Manual /Auto indication, Manual /Auto selection switch, Output voltage increase/ decrease switch,input/ output voltage indication, load current indication, including dismantling and credit for the existingKVA stabilizer with transformer oil. The stabiliser should be guaranteed for 12 months from commissioning for any manufacturing defects. In the event of any failure within the above period, replacements or rectification of parts shall be free of cost. The quoted rate should include credit for existing600 KVA stabilizer with transformer oil which will be retained by the contractor. (MAKE-VINITEC ELECTRONIC LABORATORY/ PRECISION CONTROL INSTRUMENTS/ SELVON INSTRUMENTS PVT. LTD / AUTOMATIC ELECTRIC (AE) )/PUREVOLT) |
| 95 | SITC oflead acid battery 150AH, 12V including the dismantling of existing battery, including credit for existing unserviceable battery of the same rating which will be retained by the contractor etc., complete as required. [Warranty-36Month] Make -Exide XP1500 or equivalent in Amaron & Luminuous . |
| 96 | SITC of 7AH, 12 V, VRLA maintenance-free battery including the dismantling of existing battery, including credit for existing unserviceable battery of the same rating which will be retained by the contractor etc., complete as required.[Warranty-36Month] Make -Exide12BV7B or equivalent in Amaron & Luminuous . |
| 97 | Supplying & fixing PVC Suction hose pipe ISI Marked Size 75/80mm (Make Texmo Code - A0695 or equivalent |
| 98 | Providing & fixing cast ironfoot valve size 80 mm to end of pvc hose suction pipe etc. complete as required(Make - Kirloskar/Sant/CRI/Kartar) |
