|
| 1 | Supply, erection. Installation, testing and commissioning of Hypochlorite dosing system - 1 No ( sodium hypochlorite dosage : 5 ppm ) is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - Pump Type : Electronic metering diaphragm pump - Make : Miltonroy/E-Dose /Equivalent - MOC : Polypropylene - Capacity : 0-6LPH - Maximum Back pressure : 2 (A) HYPOCHLORITE DOSING PUMP |
| 2 | Supply, erection. Installation, testing and commissioning of Hypochlorite dosing system - 1 No ( sodium hypochlorite dosage : 5 ppm ) is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - Pump Type : Electronic metering diaphragm pump - Make : Miltonroy/E-Dose /Equivalent - MOC : Polypropylene - Capacity : 0-6LPH - Maximum Back pressure : 2 (B) SODIUM HYPOCHLORITE DOSING TANK |
| 3 | Supply, erection. Installation, testing and commissioning of Instruments is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. -(A) LEVEL SWITCHES |
| 4 | Supply, erection. Installation, testing and commissioning of Instruments is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - (B) PRESSURE GAUGES. |
| 5 | Operation and Maintenance of 600 KLD water softening Plant for 5 years at Multi Storey complex (Sri Padmavathi Nilayam)Tiruchanoor.The rate is excluding GST. Under Part-B |
| 6 | Supply, erection. Installation, testing and commissioning of Softener feed pumps is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. Capacity : 30 m3/hr at 12m WC - Type of pump : Single stage, centrifugal, Monobloc with volute type delivery - MOC - Impeller : Cast Iron : - Delivery casing : Cast iron - Delivery casing : Cast iron - Motor body : Cast iron - Shaft : Carbon steel - Shaft Sleeve : Bronze - Power rating : 7.5HP - Voltage Range : 350 - 440V 3- Phase - Insulation : F Class - Protection : IP - 44 - Direction of rotation: Anti clock wize when viewed from suction side |
| 7 | Supply, erection. Installation, testing and commissioning of Sand filter 1800mm dia x 2000mm HOS - 1No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - Dia: 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367- Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Sand : 1200 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (A) SAND FILTER |
| 8 | Supply, erection. Installation, testing and commissioning of Sand filter 1800mm dia x 2000mm HOS - 1No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - Dia: 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367- Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Sand : 1200 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (B) MEDIA FOR SAND FILTER |
| 9 | Supply, erection. Installation, testing and commissioning of Sand filter 1800mm dia x 2000mm HOS - 1No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements. - Dia: 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367- Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Sand : 1200 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (C) FRONTAL PIPING |
| 10 | Supply, erection, Installation, testing and commissioning of Activated carbon filter 1800mm Dia x 2000mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements - Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Activated carbon : 900 Kgs - Activated carbon : 900 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (A) ACTIVATED CARBON FILTER |
| 11 | Supply, erection, Installation, testing and commissioning of Activated carbon filter 1800mm Dia x 2000mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements - Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Activated carbon : 900 Kgs - Activated carbon : 900 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (B) CORBON MEDIA |
| 12 | Supply, erection, Installation, testing and commissioning of Activated carbon filter 1800mm Dia x 2000mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements - Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Meterial of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) - Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release - Media : Activated carbon : 900 Kgs - Activated carbon : 900 Kgs - Pebbles : 2200 Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Type of valve - Butterfly valves - (C)FRONTAL PIPING |
| 13 | Supply, erection, Installation, testing and commissioning of water softener 1800mm Dia x 2000 mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements.- Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Material of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release.- Media : Resin T-40 Na : 1250Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Regeneration Tank : HDPE 500 Ltrs - Type of valve - Multiport valve with built ejector - (A) WATER SOFTENER |
| 14 | Supply, erection, Installation, testing and commissioning of water softener 1800mm Dia x 2000 mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements.- Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Material of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release.- Media : Resin T-40 Na : 1250Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Regeneration Tank : HDPE 500 Ltrs - Type of valve - Multiport valve with built ejector - (B) RESIN |
| 15 | Supply, erection, Installation, testing and commissioning of water softener 1800mm Dia x 2000 mm HOS - 1 No is offered with all necessary fitting and transportation to the work site, rate is excluding GST, etc., complete as directed during execution with the following minimum requirements.- Diameter : 1800mm - Height : 2000mm - Thickness : Shell : 6 mm - Dished end : 8 MM - Material of construction : MS IS 2062 Gr. A - Pipings : IS 1239 ( HEAVY ) Flanges : BS 10 Table E STD - Pipe fittings : IS 1239 PART - II - Surface cleaning : Sand Blasting - Painting : In / Outside Two coats of epoxy primer - Fasteners : IS 1367 - Gaskets : Natural Rubber - Offered with top distribution piping and bottom header and laterals - Frontal piping : Inlet and outlet, Back wash inlet and outlet, rinse outlet and air release.- Media : Resin T-40 Na : 1250Kgs - Service, backwash and air vent valves : CI Butterfly Valves - Pressure Gauges : 2 Nos - Flow rate - 25.0 m3/hr - Type - Vertical - MOC - MSEP - Regeneration Tank : HDPE 500 Ltrs - Type of valve - Multiport valve with built ejector - (C)FRONTAL PIPING |
