Tender For Supply Of Spare Parts Of Cattle Feed Plant Machinery--5 1 Coupling : F-110 Fenner make rubbe F-110 Fenner make rubber Tyre couple 2 “V” belt SPC-4750 3 Die 8 mm Tapper caller 4 Shear pin 5 Limit switch device 6 Pulley on machine 1200 mm dia 11 groove SPC section 7 Oil seal Front bearing 170x200x15/13 8 Lock pin or circlip of roller 9 Alen key holder bolt 10 Die ring 11 Scraper 12 Chuck nut of main shaft 13 Oil seal Rear bearing 140x170x15/13 14 Main bearing cover plate (front & rear) 15 Main motor pulley 225 mm dia 11 groove SPC section 16 Conditioner Drive Chain coupling 6018 17 Die hoist ARM 6010 zz 18 Door hinge bearings 6206 zz 19 Counter shaft bearing block S -618 20 Press roll assembly 32220 21 Main bearing Front-NU-328 22 Counter shaft 22318k+H 2318 23 Front die cover 24 Chuck nut of Roller 25 Acrylic Glass 200 dia x 200nt. (For seght glass ) 26 Hammer Spacer Bush set 27 Coupling F-100 rubber type couple 28 Main bearings 22319 K 29 Sleeves H-2319 30 Main Bearings UCF-208 31 Permananent Magnet 500X200mm 32 Hammer EN-42 Number of hammers 72 nos, overall Dimension of beaters 142x63x8mm 33 Sieve Thickness 2.5mm, Screen size 1475x675mm, Mesh width 4 mm 34 Vibration Dampers VBPGS-2D polybond make 35 Drive End bearing UCF, F-208 36 Drive End bearing F-208 37 Coupling Chain coupling ‘ 1’pitch, 22 teeth simplex chain 38 Gear Box PBL, Model M-062232 BGCH 1-1-5A 39 Coupling F-60 Tyre Type 40 Air cylinder 50 dia 150 stroke double acting pneumatic cylinder 41 Main bearing 1216K 42 Sleeve H316K 43 Pedestal S 516 44 Wood slats Seasoned wood Slat dimension 550x80x30 45 Bolts for fitting the slats 46 Chain for the conveyor 47 Gear Box Elecon, Model 1044293 48 Motor Siemens, Model E 0708/505840211004, 1.5 K / 2 HP 49 Coupling size F-70 50 Drive end bearings SKF ,UKF-209 51 Shaft end bearings SKF ,UKP-209 52 Rotor Shaft Material : End Dia: 40mm Pin rods: MS 10mm dia 53 Gear Box Bongfiglioli, AS30 PP90 54 Elevator Bucket 8” -2 Bolt bucket 55 Belt Solivator 500 56 Coupling Direct coupling (size 6018 – Dia 48/Dia45) 57 Driven Section Bearing UCF, SKF, F-208 58 Gear Box COUPLING Bongfiglioli, AS45-PP112, 6018 (Dia 48/Dia45) 59 Bottom liner Plate UHMWPE 10mm 60 Chain cleaning device Brush 61 Wear rail TiscRal or eqivalent material 62 Side Plate thickness H.R. IS 2062, 5mm, 4mm 63 Bottom plateThickness H.R. iS 2062, 5mm 64 Bottom wear plate thickness UHMW 10mm 65 Top Plate Thickness 3mm 66 Sprocket 4” pitch, 7 teeth, 65 Dia. 67 Drive section Bearing UCF-NTN UCF-212 68 Driven section Bearing UCF-NTN (UCF-208) 69 Gear Box Coupling 6018 (Dia 58/Dia 60) 70 Magnet unit SS 304, Min. 6000 Gauss Swing type with pneumatic cylinder 71 Main screw pipe Heavy duty ‘c’ class MS ERW pipe, Dia 76- c class 72 Drive end bearing SKF, Flange Type ball bearing-FY510 73 Drive shaft bearing EN 24 74 Driven end bearing FY 510 SKF 75 Gear Box Bongfiglioli, AS45 PP 112 76 Gear Box Coupling 5018 (Dia 48/Dia 45) 77 Connector ¼”-8 78 Solenoid valve MMFH-5-1/4 (Solinoid valve) 79 Solenoid Coil MSFW/24-42-50/60 (Solenoid coil) 80 SCREW Dischargers Eminence, SC-250, 1.53MX 08 Nos, 1.2MX 4 Nos, Screw Dia. 250 mm 81 Main screw pipe Heavy duty ‘c’ class MS ERW pipe, Dia 76-C class 82 Gear Box Bongfiglioli Model AS30PP90 83 Gear Box Coupling 5016 (Dia 38/Dia 30) 84 Drive shaft bearing EN24 85 End bearing SKF, Flange type ball bearing-F208 86 Coupling Type Simplex chain coupling 87 Bearing F-201 TR Make 88 Rotor Type Wane Type 89 Gear Box PBL, M052236 BGCH 1-1-1A 90 Signt Glass details for Airlock Dia- 250 91 Gear Box- Airlock PBL, Model C042045/WGHJA 92 Bearing TR, Bearing Model F-205 93 Sieve Perforated, 2 decks 94 Pressure Switch Alfa, Model PR-9X, Range 2.5-9.5 kg/cm2 95 Pneumatic cylinder Festo, Pneumatic cylinder specification DNC-125-160-PPV-A 96 Pneumatic pipe 12 mm, Make of pipe janatics 97 Connector ½”-12 mm 98 Solenoid valve MFH-5-1/2 99 Solenoid Coil MSFG/24-42 – 50/60 100 Bottom liner Plate UHMWPE 10mm 101 Wear rail Tiscral or equivalent 102 Chain Drag bush chain type link – C45/En8D ‘Pin – 18 MnCr5/20MnCr6 103 Drive Bearing UCF-NTN (UCF-212) 104 S rocket 4 “pitch. 7 teeth 65 Dia 105 Side plate thickness in mm H.R. IS 2062, 5mm, 4mm 106 Bottom plate thickness H.R. IS 2062, 5mm 107 Bottom wear plate thickness UHMW H.R. IS 2062, 5mm 108 Top plate thickness in mm H.R. IS 2062, 3mm 109 Intermediate plate thickness H.R. IS 2062 3mm 110 Sprocket 4” pitch, 7 teeth, Dia. 65 111 Driven Bearing UCF-NTN (UCF-208) 112 Zero Speed sensor (3 Wire) 113 Gear Box Bongfiglioli, Model AS 60 DPP112 114 Coupling size 6018 (Dia 58/Dia 60) 115 Chain Drag bush chain type (Link – c45/En8D ; Pin – 18MnCr5/20MnCr6) 116 Bottom liner Plate UHMWPE 10mm 117 Wear rail TISCRAL or equivalent material 118 Side plate thickness in mm H.R. IS 2062, 5mm, 4mm 119 Bottom plate thickness H.R. IS 2062, 5mm 120 Bottom wear plate thickness UHMW H.R. IS 2062, 10mm 121 Top plate thickness in mm H.R. IS 2062, 3mm 122 Intermediate plate thickness H.R. IS 2062, 4mm 123 Sprocket 4” pitch, 7 teeth, Dia.65 124 Gear Box Bongfiglioli, Model AS 60 DPP 112 125 Coupling size 6018 (Dia 58/Dia60) 126 Main body plate ss-304, 4mm Thk 127 Conditioner Paddle- ss-304, 6mm Thk 128 Doors for cleaning ss-304, 4mm Thk 129 Chain conveyor galls 30cm,19cm ¼30x19½ 130 Pellet sieve 6x4 Feat ¼180cm x 120 cm ½ (screen size) 131 Perforated Sieve for Hammer Mill (FCS-100) (4mm perforation) 132 Wire Mesh for pellet sieve 4 mesh 133 Acrylic Glass 200 dia x 200 ht. 200 dia x 200 ht (for cyone glass) 134 Hammer spacer bush set (20, 48& 58 mm long) 135 SUS Front die cover ({pellet mill) (TC M 20 Bolt) 136 SUSW SS End Cover (SS-304 construction) 137 Roller Shells “V” grooved for above Size 250mm OD 180mm ID (Suitable for bearing no. 32220, 182mm wide
