Ht Box And Cabelling Work Ht Box And Cabelling Work , Ht Box & Cabling Work , Supply, Installation, Testing & Commissioning Of Ht Metering Cubical Panel As Approved By Discoms Fabricated Out Of 14 Swg Crca Sheet Steel In Two Compartment & Ms Angle Of , Udaipur-Rajasthan

Ht Box And Cabelling Work Ht Box And Cabelling Work , Ht Box & Cabling Work , Supply, Installation, Testing & Commissioning Of Ht Metering Cubical Panel As Approved By Discoms Fabricated Out Of 14 Swg Crca Sheet Steel In Two Compartment & Ms Angle Of Size 60Mmx6mm Having Provision For Following: ( I ) Provision For Fixing Trivector Meter ( To Be Supplied By Discoms ) ( Ii ) Provision For Fixing Of Combined Ct Pt Set ( To Be Supplied By Discoms ) , ( Iii ) Tt Block, ( Iv ) 6Mm Bakelite Sheet On All Sides, ( V ) 3 / 6 Core Copper Cable For Interconnections Etc. As Required Complete In All Respect. All As Per Pre Approved By Engineer In Charge.For Additional Technical Parameters Of Products / Work, Refer Annexure A Attached With This Bsr . , Providing & Laying Xlpe Insulated As Per Is:7098 / Ii / 85H.T.Cable As Per Pwd Specification For Electrical Works For Working Voltage 11 K.V. ( E ) In Existing Rcc / Hume / Stoneware / Pvc Pipe / Open Duct / Cable Trench With Filling Of Excavated Earth In Trench, On Existing Cable Trays Or On Surface Etc.Including Making Necessary Connection, Testing Etc. As Required Of Size As Per Points ( A ) , ( B ) , ( C ) Mentioned Below:- ( A ) Material :- H4- Gradealuminium Conductor Of Purity >99.6 %& As Peris:1554 P-I / Is :7098 P - I ( B ) Conductor Shall Have Electrolytic Aluminium Confirming To Is 8130, Is 3975-1999For Armouring Of Cables , Is 5831 For Sheath, Is 10810 ( Part 0 To 64 ) For Testing Procedures ( C ) Oem Must Have Iso 9001 & 14001 Certifications For Quality Assuarance & Its Own In House Nabl Lab Setup For All Testing Facilities Forcables. All Above As Per Pre Approved By Engineer In Charge.For Additional Technical Parameters Of Products / Work, Referannexure A Attached With This Bsr . 3 Core 185.0 Sq.Mm , Providing & Making Heat Shrinkable Type Indoor / Outdoor / Straight Through Terminations / Joint Kit As Per Pwd Specification For Electrical Works Suitable For11 Kv / 33 Kv Cable With Required Components, Prepration Of Cable Ends. Type Test Report Should Be As Per Is13573:2011 Which Covered All Sequence For Table 2 For Termination Kit And Table 3 For Streightthrough Joint Inclusive Thermal & Dynamic Short Circuit Test, Humidity Test, Soil Fog Test. Crosslinking Shall Be Done Out Side Factory With E- Beam / Peroxide Technology. Extrusion Process Shall Be In House Oem Within Same Vicinity. Oem Test Lab Should Be As Per Iso 9001:2015 & 14001 : 2015 & Reports Submitted To Engineer In Charge Includingtesting Etc. As Required Of Following Sizes. All As Per Pre Approved By Engineer In Charge.For Additional Technical Parameters Of Products / Work, Refer Annexure A Attached With This Bsr . 11 Kv End Termination Kit Indoor Type 3 Core 120 / 150 / 185 Sq.Mm , 11 Kv Straight Through Jointkit 3 Core 120 / 150 / 185 Sq.Mm , Random Rubble Stone Masonry For With Hard Stone In Foundation And Plinth In Cement Sand Mortar Above 30 Cm Thick Wall In: Cement Mortar 1:6 ( 1-Cement : 6-Sand ) . , Plaster On New Surface On Wall In Cement Sand Mortar 1:3 Including Racking Of Joints Etc. Complete Fine Finish: 20Mm Thick , Supply & Laying Following Size Earth Wire In Horizontal Or Vertical Run In Ground / Surface / Recess Including Riveting, Soldering, Saddles, Making Connection With Gi / Cuthimble Etc. As Required.All As Per Pre Approved By Engineer In Charge.For Additional Technical Parameters Of Products / Work, Refer Annexure A Attached With This Bsr . 8 Swg Copper Wire , 8 Swg G.I. ( Hot Dipped ) Wire

INR 200 /-

INR 4487.0 /-

INR 2.50 Lakhs /-