Supply And Installation Of Engineering Workshop Lab Equipment And Tools At Rgukt, Srikakulam 1 Bench vice 7 8 2 Flat file rough 10” 10 3 Flat file bastered 12” 10 4 Half round file rough 10” 10 5 Triangular file rough 10” 10 6 Needle file set 1 se, Srikakulam-Andhra Pradesh

Supply And Installation Of Engineering Workshop Lab Equipment And Tools At Rgukt, Srikakulam 1 Bench vice 7 8 2 Flat file rough 10” 10 3 Flat file bastered 12” 10 4 Half round file rough 10” 10 5 Triangular file rough 10” 10 6 Needle file set 1 set 7 Square file rough 10” 4 8 Smooth file 10” 4 9 Knife edge file 6” 4 10 Round file 8” 4 11 Hacksaw frame 20 12 Try square 4” 4 13 Try square 6” 10 14 Scriber 10 15 Prick punch 10 16 Centre punch 10 17 Number punch 4 18 Leather punch 4 19 Dot punch 10 20 Ball peen hammer 500 gms 12 21 Inside calipers 6” 4 22 Outside caliper 6” 4 23 Jenny caliper 6” 4 24 Divider 6” 15 Page 9 of 25 25 Steel rule 20 26 Vernier height Gauge 1 27 Micrometer 4 28 Vernier calipers 4 Trade No. 2 Tin Smithy S No. Name of the Tool & Equipment Specification Quantity 1 Steel Rule 300 mm 12 2 Ordinary Wooden Mallet 10 3 straight snip 10 4 Scriber 150 mm x 3 mm (Engineers) 10 5 Tri Square 6 10 6 Sheet Metal Gauge 10 7 nose plier 10 8 Wing Divider 200 mm 10 9 Centre Punch 100 mm 10 10 Protractor with blade 150mm 5 11 Steel tape 2 metres 4 12 solid punch 4 13 Prick punch 100mm 10 14 hollow punch 4 15 Spring Dividers 150 mm 5 16 Chisels 5 17 Hacksaw frame 300 mm adjustable (Tubular) 4 18 bent or curved snip 4 19 rivet set 5 20 Blow Lamp 1 liter capacity 2 21 Trammel Point with beam 600 mm 1 22 Vernier caliper 0 mm - 150 mm 4 23 Micrometer Outside 0 to 25 mm 4 24 Funnel Stake 1 25 Anvil Face Stake 1 26 Square stakes 1 27 Hand vice 50 mm 4 28 Setting hammer 4 29 Riveting hammer 4 30 Raising hammer 4 31 Round File 2nd Cut 250 mm 4 32 Triangular File Smooth 250 mm 4 33 Square File 2nd Cut 250 mm 4 34 Needle File (Swiss File) 150 mm 1 35 C Clamp 150 mm 5 36 Bench leaver shears 250 mm Blade x 3mm Capacity 1 37 Bench vice 1 Steel rule Twelve inch 10 2 Try Square 200mm 10 3 Carpenter marking gauge 6 4 4 Tenon saw 300mm 4 5 Metal Jack plane 335mmX 50mm cutter 6 6 Firmer Chisel 25 mm 10 7 Scriber 10 8 Mallet medium size 10 9 C clamp 100 mm 4 10 Carpenter vice 250 mm jaws 4 11 Foot rule/steel tape Two ft. Four fold/6 mtrs 4 12 Marking Knife 200 mm length 4 13 Bevel Square 50 mm 4 14 Carpenter mortise gauge 4 15 Hand Saw 450mm 6 16 Metal smoothing plane 200mm X 50mm cutter 4 17 Firmer Chisel Bevel edge 6mm. 10 18 Mortise chisel 06, 10, 15mm (3 nos.) 5 19 Claw hammer 500 gms 5 20 Oil stone Carborundum universal silicon carbide 4 21 Hand brush for cleaning 450mm 10 22 Wing compass 300 mm 10 23 Trammel 300 mm 2 24 Sprit level 300 mm 4 25 Cross cut saw 250 mm 2 26 Key hole saw 250 mm 1 27 Fret saw frame 150 mm 2 28 Spoke shaves 50 mm Cutter 4 29 Pincer 50 mm 4 30 File half round 2nd cut 250 mm 6 31 File half round Wood rasp bastard250mm 6 32 Hands drill 6 mm Capacities 4 33 Ratchet brace 250 mm Swap 1 34 Hand auger 10,12,14,16,18,20,2 2,25 mm 1 35 Divider 6 10 36 Rasp 8 4 Page 11 of 25 37 Bevel edge firmer chisel 12 4 38 Bradawl 6 4 39 sash clamp 1 Trade No. 4: Black smithy S No. Name of the Tool & Equipment Specification Quantity 1 Anvil 50Kgs 2 2 Tongs 750 mm length 6 3 Chisel hot 6 4 Ball peen hammer 1 kg 2 5 Ball peen hammer 750 gm 2 6 Ball peen hammer 1250 gm 4 7 Cross peen hammer 750 gm 2 8 Cross peen hammer 1 Kg 2 9 Straight peen hammer 750 gm 2 10 Straight peen hammer 1 Kg 2 11 Sledge hammer 3Kg 1 12 Sledge hammer 5Kg 1 13 Brass rule hot condition 600mm 2 14 Induction furnace 1 15 Hand gloves Leather 10 16 Swage block 12 x 12 Inch 1 Trade No. 5 Welding S.NO. Name of the Equipment Specification Quantity 1 Acetylene Gas Welding Setup 1 2 ARC Welding Setup 1 3 Welding Cables 1 4 Flat Nose Tong 500 mm 4 5 Electrodes 3.5 mm dia 4 6 Ground Clamp 4 7 Wire Brush 500 mm 8 8 Chipping Hammer 370 gms 5 9 Hand Gloves leather 10 10 Face Shield 30cm x 20cm x 8cm 10 11 Rough Flat File 6 12 Try Square 6 8 13 Steel Rule 300 mm 10 14 Ball Peen Hammer Trade No. 6 Plastic Processing S.No. Name of the Tools & Equipment Specification Quantity 1 Injection Moulding Machine Manual 1 No. 2 Extrusion Blow Moulding Machine with set of moulds and accessories - 1 to 2 liter capacity (with Microprocessor/PLC controller) 1 No. Trade No. 7 Foundry S.No. Name of the tool Specification Quantity 1 Molding Board As per foundry standards 5 2 Molding Flask 5 3 Shovel 5 4 Rammer 5 5 Strike Of Edge /Strike Of Bar 5 6 Sprue Pin 5 7 Riser Pin 5 8 Trowel 5 9 Spike Or Draw Pin 5 10 Slick 5 11 Lifters 5 12 Gate Cutter 5 13 Bellows 5 14 Vent Rod etc

Sr No	CorrigendumDate	Corrignedum	CorrigendumType	NewSubmissionDate
1	05-03-2022		lL	02-03-2022
2	16-03-2022		Corrigendum-3	22-03-2022
3	20-02-2022		Corrigendum	02-03-2022
4	29-03-2022		Tender cancelation notice	22-03-2022

INR 10000 /-

INR 50000.0 /-

Refer document