Bids Are Invited For Steam Generator: Make: Clayton, Type : Eo-100-1M, 0Lw15ppm, Qty: 01, Location : Mer - Carry Out Following Refit Routines On Steam Generator. Materials And Spares Firm Supply.(I) Clean Blower Rotor And Check Burner Volute Pressure.(Ii)-Goa

Bids Are Invited For Steam Generator: Make: Clayton, Type : Eo-100-1M, 0Lw15ppm, Qty: 01, Location : Mer - Carry Out Following Refit Routines On Steam Generator. Materials And Spares Firm Supply.(I) Clean Blower Rotor And Check Burner Volute Pressure.(Ii) Replace Burner Nozzle. Clean/Adjust Burner And Check Burner Safety Control.(Iii) Replace Oil In Crankcase. Drain And Refill Water Pump Crankcase With New Hydraulic Oil.(Iv) Inspect Water Pump Check Valves. Replace Seats And Discs If Worn.(V) Inspect Pump Diaphragms. (Vi) Inspect All Air, Fuel, Water Control Linkages For Wear, Screw Tight And Free Movement.(Vii) Set Steam Pressure Parameter And Limit Pressure Switch (F21) To Exceed Steam Relief Valve Pressure Setting. Allow Pressure To Increase Until Steam Safety Actuate. After Test Is Accomplished, Regulate Limit Pressure Switch And Reset Steam Parameter To Desired Working Pressure. (Viii) Test Steam Safety Valves (30), Tp: 10 Bar, Qty: 02.(Ix) Open Steam Discharge Valve Completely. Service Or Replace Steam Safety If Test Fails.(X) Overhaul Chemical Dosing Unit And Pump.Spares – Cg Supply.Material – Firm Supply , Steam Generator: Make: Clayton, Type : Eo-100-1M, 0Lw15ppm, Qty: 01, Location : Mer 1 - Carry Out Water (Exhot Well) Quality Test. Maintain Hardness (00Dh), Alkalinity (10-12 Ph), Sulphite (Min 50 Ppm) And Conductivity (Max. 6000 Μs/Cm) Prior Steam Generator Trials Post Repairs.Spares – Cg Supply.Material – Firm Supply , Steam Generator (M/S Clayton, Model-Eo-100-1M) - (A) Overhaul Steam Generator Plus Blower Motor,415V,7.5 Kw,3 Phase And Chemical Pump .Overhauling Includes Overhauling Includes Record Of Insulationprior Dismantling Of Motor And Withdrawal Of Rotor, Renewal Of De/Nde Ball Bearing On Opening, Spray Painting Of Heat Resistive Paint On External/Internal Part Of Yoke, Apply Of Varnish And Baking Up For 10 Hour. Renewal Of All Consumable, Recordingofinsulation,Starting/Runningcurrentandprovingofmotorfor Satisfactory Operation On Completion Of Overhauling.(B) Overhaul Complete Overhauling Of Steam Generator Control Panel. Overhauling Includes Contactor(K99)&Q1,Andaux.Contactor,Controltransformer, 415V/220V/24 V,Ignition Transformer,230V/6000 V. And 3-Way Valve, Heating Coil, Pressure Switch And Combustion Controller And Solenoid For Filling, Bypass And Damper. Calibrate Overload Relay (Set-95-97 Amp). Following Alarm /Stop To Be Checked For Satisfactory Operation:- (I) Generator Overload(Ii) Excessive Steam Pressure(Iii) Wrong Oil Level In Crankcase(Iv) Water Failure(V) High Steam Temperature(Vi) Insufficient Fuel Pressure (Vii)Insufficient Combustion Air Pressure At Blower Insufficent Combustion Air At High Fire Flame Failure.(Viii)Carryoutfunctionalcheckofcompletesystemoncompletionof Overhauling And To Be Proved For Satisfactory Operation.Cg Supply.Material – Firm Supply Total Quantity : 1

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	05-01-2022			12-01-2022
2	12-01-2022			15-01-2022
3	18-01-2022			19-01-2022
4	29-01-2022			01-02-2022

Refer document

Refer document

Refer document