Bids Are Invited For Serviceability Checks / Overhaul Of Electronic Equipment - ( A ) Clean Dust, Dirt And Moisture From The Internal And External Surface Of The Units. ( B ) Check Connectors For Proper Mating And Grounding. ( C ) Clean All Pcbs / Modules And Check For Correct Functionality. Procure And Renew If Faulty. ( D ) Smps / Power Supply Unit To Be Checked For Rated Input / Outputs. Renew If Faulty. ( E ) Systems Having Software To Be Checked For Correct Functionality. ( F ) Check The Cable And Connectors For Cuts, Corrosion Or Undue Strain. ( G ) Clean The Air Filter With Vacuum Cleaner As Applicable. ( H ) Check The Set For Optimum / Designed Performance And Reliability. ( J ) Replace The Defective Lamps / Caps / Fuses / Hinges / Screws / Knobs / Keys / Switches. ( K ) All Existing Shock Mounts / Base Plates / Foundations To Be Checked For Integrity And Renew If Necessary. ( L ) Renew All Earthing / Bonding Straps. ( M ) Renew All Terminal Lugs ( N ) Renew Of Emi / Emc Gaskets Of All Openings Of Equipment. ( P ) Interfacing To All Systems To Be Proved As Applicable. ( Q ) Carry Out All Annual Routines And Performances Tests As Per Maintop At Shop Floor , Post Overhaul / Serviceability Checks - Post Overhaul / Repair / Routines Following To Be Carried Out:- ( A ) All Systems / Equipments / Machinary Should Be Proved To Rated / Designed Power / Capacity Without Limitations / Observations And Trials To Be Offered To The Naval Trial Agencies For Design Specifications Along With Installation Inspections As Per Approved Wlds, Op Checks, Hats And Sats. ( B ) Any Unserviceability During Undertaking Above Serial Needs To Be Repaired / Renewed By Firm Inclusive Of Spares. ( C ) Vibration Levels At All Points Should Be Less Than 5 Mm / Sec.The Equipment Performance Will Be Considered Satisfactory Only If The Performance Trials Are Cleared By Naval Inspection Agency. ( D ) Present System For Hats And Sats As Per The Standards Of Watt. , Overhaul Of Antennas And Aerials - ( A ) Clean And Examine Whip And Wire Aerials For Pitting / Cavities, Replace All Defcetive Components. Apply Rf Paint To Antennas. ( B ) Check Insulation Of Wire Aerial, Value Should Be More Than 2 Mega Ohms, If Strands Are Cut / Broken To Be Replaced. ( C ) Renew Porcelean Insulators Of Wire Aerial If Required. ( D ) Replace Insulator Of Antenna If Defective ( E ) Base Plate Of Antenna Is Corrodedto Be Manufactured And Fitted. ( F ) Work Includes Removal / Refitment Of Antenna. ( G ) Antenna Foundation Box Is Corroded, To Be Removed And New Box As Per Original Dimensions To Be Manufactured And Fitted / Welded On The Respective Antenna Place. , V / Uhf Search Rx Elk-7036 ( I ) - Make : Bel Hydmodel : V / Uhf Search Rx Elk-7036 Serial No : 704101580010 Oems Local Representative : M / S Bel, Hyderabadother Details ( N / A ) : Power Cons -1.1 Kva, Receiver Frequency Range ( Khz ) : 20-1250 Mhz, Supply Frequency ( Hz ) : 45-65, Supply Phase ( Ph ) : 01, Supply Voltage ( Volts ) : 90-240 , V / Uhf Search Rx Elk-7036 ( Ii ) - Overhauling Of Complete System As Per Sow 3. , V / Uhf Search Rx Elk-7036 ( Iii ) - Overhauling Of Antenna As Per Sow 5 , V / Uhf Search Rx Elk-7036 ( Iv ) - Post Overhaul / Serviceability Checks As Per Sow 4. , Sanket Mk Ii ( Mt-73112 ) - Make: Bel, Hydrabad Model: Mk Oems Local Representative: M / S Bel, Hydrabad ( A ) Check The Rf And Video Tangential Signal Sensitivity At Ahu Output In Normal Mode By Feeding The Rf Signal At Ahu Using Rf Generator. , 1 ( Sanket Mk Ii ( Mt-73112 ) ) - ( B ) Check The Dc Offset Volttages For Each Fer Chennel And Ensure That The Dc Offset Voltage Is Within Specified Limit Using Test Equipment. , 2 ( Sanket Mk Ii ( Mt-73112 ) ) - ( C ) Open The Ahu Back Cover And Inspect All The Semi-Rigid Cables For Intactness.Ensure That They Are Tightened Properly Using Torque Wrench. , 3 ( Sanket Mk Ii ( Mt-73112 ) ) - ( D ) Carry Out Level-2 Maintenance Which Includes Repair Of Pcbs, Replacment Of Components And Sub Assemblies In The Shop Floor. , 4 ( Sanket Mk Ii ( Mt-73112 ) ) - ( E ) Inspect The Ew Cables Run Of Both Normal And Co-Oxial Wire For Intactness And Continuty. , 5 ( Sanket Mk Ii ( Mt-73112 ) ) - ( F ) Replace The Gaskets With New Set And Apply Grees Before Closing The Unit Covers Wherever Applicable. , 6 ( Sanket Mk Ii ( Mt-73112 ) ) - ( G ) Remove The Radomes, Clean And Stow Them Safely. , 7 ( Sanket Mk Ii ( Mt-73112 ) ) - ( H ) Overhaul / Serviceability Checks Of Full System To Be Carried Out As Per Sow 3. Procure And Replace All Faulty Components By Refitting Yard. , 8 ( Sanket Mk Ii ( Mt-73112 ) ) - ( J ) Carry Out Complete Performance Checks Of The System. , 9 ( Sanket Mk Ii ( Mt-73112 ) ) - ( K ) Carry Out The Hats Schedules As Per Sow 4 And Ensure That The System Is Functioning Satisfactory. , 10 ( Sanket Mk Ii ( Mt-73112 ) ) - ( L ) Carry Out Calibration / Servicing / Repair Of Pcbs, Connectors And Sub Asseblies As Applicable.Obtain Oem Assistance If Necessory , Mandotary Spares 1 ( Eb3050b-172200061696 ) - Cpu Card , 2 ( Eb3050b-172200061795 ) - Synthesizer Card Assy , 3 ( Eb3050b-172200061987 ) - Iner Face Card Assy , 4 ( Eb3050b-457672630186 ) - Pc Power Supply , 5 ( Eb3050b-480578080109 ) - Hard Disk , 6 ( Eb3050b-480672300186 ) - Keyboard Drawer , 1 ( Na ) - 3 Kva Online Ups , 2 ( Na ) - 12V, 42 Ahbattery Total Quantity : 1
