Bids Are Invited For Almirah Large Steel (1/2Hx1/2S) Fd/E6/Map/18 - Almirah Large (Stee) 1/2 Hanging 1/2 Shelving:- All As Shown On Drawing. Overall Size Shall 920Mm Long, 485Mm Wide And 1985Mm High. The Base Shall Be 100Mm High. The Base Shall Be Made Of-Meghalaya

Bids Are Invited For Almirah Large Steel (1/2Hx1/2S) Fd/E6/Map/18 - Almirah Large (Stee) 1/2 Hanging 1/2 Shelving:- All As Shown On Drawing. Overall Size Shall 920Mm Long, 485Mm Wide And 1985Mm High. The Base Shall Be 100Mm High. The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channels Shape With Ends Covered And Weldedto Bottom Of Almirah. Mild Steel Sheet For Channel Shall Be 1Mm Thick. The Base Channel Shall Be Welded At 50Mm From Each End Of 920Mmlength. Top, Sides, Back, Bottom And Front Of Almirah Shall Be 1Mm Thick Mild Steel Sheet. Two Shelves Shall Be Provided At 350Mm And 700Mm From Bottom Of Almirah. Ahan Ging Rod 60Mm From Top Shall Be Provided Which Shall Be Of 20Mm Dia Steelchromium Plated Conduit Pipe Of Wall Thickness 1.25Mm. Two Sockets Shall Be Provided At The End Of Hanging Rod. Front Shutters Shall Have Two Leaves. A Steel Chromium Plated Handle 100Mm Long Shallprovided To Shutters. A Three Way Locking Device Shall Be Provided To Front Shutters. Each Leaf Of Front Shutter Shall Be Hinged With Three Nubers Butt Hinges 75Mm Long And Shutters Shall Be Side Hung. All Joints And Welding, Fixing Shall Be Done With Standard Workmanship. All Hung. All Joints And Welding, Fixing Shall Be Done With Standard Workmanship. All Steel Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Enamel Paint Over A Coat Of Primer After Preparation Of Surfaces. Painting Shall Be Done With Spray Machine. , Bed Hard Fd/E6/Map/08R - Overall Size Shall Be 2050Mm Long, 900Mm Wide And 400Mm High. All Steel Shall Be Ms Square Pipe Of 18 Gauge. The Head Board Shall Be 800Mm High And Foot Board Shall Be 500Mm High. The Frame Of Head Board And Foot Board Shall Be Of 38Mmx38mm Ms Square Pipe.18Mmx18mm Ms Square Pipe Shall Be Provided In The Inner Of Head Board Frame/Foot Board Frame As Shown In Drg.18Mm Thick Both Side Decorative Prelaminated Particle Board Of Walnut Shade With Pvc Edging Shall Be Screwed To Ms Strip Arc Welded To 18Mm Thick Rectangular Pipe With Standard Workmanship Both In Head Board/Foot Board..25Mmx65mm Rectangular Cr Pipe Shall Be Used To Make The Long Railsand Short Rails Of Bed Hard And Welding Shall Be Done For Fixing Long Rails To The Legs Irrespective Of What Is Shown On Drg.One Stiffener Of Size 25Mmx25mm Shall Be Welded Between The Two Legs Ofheadboard Over 150Mm From The Ground Level. The Top Of Bed Hard Shall Be Of 12Mm Thick Bwr Ply Of Approved Makefixed Over The Four Equidistantstiffener Of Size 25Mmx25mm Sq Ms Pipe In Line With Bottom Of 25X65mm Long Rail Section. Pvc Shoes Shall Be Provided To Legs Of Bed.All Metal /Iron Work Shall Be Treated With Synthetic Enamel Black After Doing Two Coats Of Metal Primer.Rest All As Per Drg. , Charpoy Hardtop Ip Fd/Map-Ii/01 - Dimension: Overall Size Shall Be 1980Mm Long, 900Mm Wide And 440Mm High.Description:Two Long Rails And Two Short Rails Shall Be Of 25Mmx65mmx16 Guage Ms Rectangular Pipe .The Legs Shall Be Of Size 32Mmx32mmx16 Guage Welded To Long And Short Rails As Shown On Drg.Two Stiffeners Of Size 25Mmx25mmx16 Guage Shall Be Provided In Equidistant Between Two Opposite Long Rails. Six Number Cleat Of Size 25Mmx60mmx6mm Shall Be Welded With Frame To Support Ply. Two Stiffeners Joining Legs Of Size 25Mmx25mmx16 Guage Shall Be Provided At 150Mm From Ground Level .12Mm Thick Commercial Plywood Shall Be Provided For Top As Shown On Drg With Proper Nut And Bolt .Pvc Hard Rubber Shoes Shall Be Fixed At Bottom Of Each Legs.Finish: All Steel Surfaces Shall Be Pre Treated With Epoxy Powder Caoted Oven Baked With Black Colour. , Chair Computer Fd/E6/Map/01 - The Base Pedestal Assembly Of Chair Computer Shall Be Of Dia 700Mm And 1060Mm High .The Pedestal Assembly Shall Be Provided With Injection Molded In Black 30% Glass Filled Nylon. A 10.5Mm Dia Forged Bright Zinc Plated Ms Castor Pin Is Of Press Fitted Into Each Prong For Holding The Castors. The Seat And Back Of The Chair Computer Shall Be Made Of 12Mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Back Form Shall Be Designed With Contour Lumber Support For Extra Comfort With Pvc Lipping Allround.The Back Rest Shall Be Adjustable And Consist Of Drop Lift Mechanism And Shall Be Adjusted In The Insert .It Shall Be Scratch And Weather Resistant. Rest All As Per Drg.And As Per Sample Approved By Bso/Ge , Locker Steel Fd-1029 - Locker Bed Side Steel:- Overall Size Shall Be 760Mm Long, 600Mm Wide And 1100Mm High. All Mild Steel Shall Be 1Mm Thick. Two Legs Shall Be Provided To Lockers As Shown On Drawing And Shall Be Of 1Mm Thick Mild Steel Sheet. Top Sides, Back, Front And Shelves Shall Be Of Mild Steel Sheet Of 1Mm Thick. Two Handles, Chromium Plated, 100Mm Long Fixed To Shutters. One Hasp And Staple 75Mm Long Shall Be Fixed To Shutters. The Shutters Shall Have The Locking Device Also. The Weight Of The Locker Shall Not Be Less Than 42 Kgs. All Steel Surface Internally And Externally, Exposed To View When Placed In Position Shall Be Given Two Coats Of Silver Grey Paint Of 1St Grade Over A Coatof Primer After Properly Smoothened The Surface With Sand Paper And Applying Putty. Painting Shall Be Done With Spray Machine. Rest All Specifications Areas Per Drg . , Shoe Rack Steel Fd/E6/Map/02R - (A) The Main Frame Shall Be Made Of 25Mm Dia, 18G Crca Pipe And The Main Shelf Fram With 19Mm Dia, 18 G Pipe (B) There Shall Be Five Shelves, Each Of Size 300Mmx700mm And The Space Of Each Shelf Shall Be Covered By 3Mm Dia Ms Rods Three In Length Wise And Nine Widthwise (C) All Ms Members Shall Be Pre-Treated With Epoxy Polyester Powder Coating (Black) 70 Microns By 7 Tank Process And Oven Dried Internally & Externally With The Following Specifications (I) Dry Film Thickness More Than 45 Microns (Ii) Salt Spray Test To With Stand More Than 1000Hours (Iii) Adhesion As Per Din 53152 Standards. (Iv) Pencil Scratch Hardness More Than 2H (D) Welding Process Shall Be Of Mig(Metal Inert Gas) Type Using Carbon Dioxide And Argon Blend (E) Rest All As Per Drg Or As Specified. , Table Computer Fd/E6/Map/03 - Dimension:-Overall Size Of Top Shall Be 900Mm Long,561.20 Mm Wide And 750Mm High.Description:-Allprelaminated Particle Board Used In Manufacturing Of Top ,Shelves,Drawers,Tray Shall Be Of 18Mm Thick Prelaminatedboard.The Frame Of Table Shall Be Of 25Mm Square Pipe Of Wall Thickness Not Lss Than 1.6Mm.The Top Of Table Shall Be Provided With 4Mm Thick Teak Wood Beading.The Legs Shall Be Made Out Of 25Mmx50mm Ms Rectangular Cr Pipe Of 18 Guage.Each Leg Shall Be Provided With Rectangular Pvc Cover Made To Shape On Front Sides Only.The Drawers Shall Be Provided With Telescopic Channel 300Mm Long.The Legs Shall Also Be Provided With Nylon Buffers .Rest All As Per Drg.Finish:- All Wood Surfaces Shall Be French Polished With High Gloss Finish Rest All As Per Drg. , Table Office Officer Steel Fd-1003 - Dimension: Over All Size Shall Be Of 1680X870 X760mm.Description :25 Mm Ms Square Tube 1.6 Mm Thick Shall Be Provide To Frame 1 Mm Thick Ms Sheet Nominal All Around For Drawer.Top Shall Be Of 18Mm Thick Pre-Laminatedboard Isi Mark (Exterior Gde) One Side Decorative Finish Approved By Ge And 4 Mm Thick Teak Wood Edging All Around Shall Be Provided For Top.Three Drawers Shall Be Provided On Right Hand Sides Of Table.A Cupboard With Front Openable Door Shall Be Provided On The Left Side Of The Table.A Shelf Shall Aslo Be Provided At The Middle Of Cupbaord.All Sheet For Drawers Shelf And Cupboard And Back Covering Shall Be 1Mm Thick.Hard Rubber Shoes Shall Also Be Provided To The Bottom Of Legs.Rest All As Per Drgsfinish: All Steel Surfaces Exposed To View When Placed In Position Shall Be Paintedwith Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces.A Mark Of Mes Shall Also Be Provided On Top Left Corner Of Front Shutter With Visible Colour. Painting Shall Be Done With Spray Machine.Rest All As Per Drg. , Table Office Clerk Steel Fd-1004 - Dimension: Overall Size Shall Be 1200Mm Long, 610Mm Wide And 760Mm High.Description:Steel Frame Shall Be Of Size 1160X570x742mm .Four Legs Of 25Mm Mild Steel Tube Of 1.6Mm Wall Thickness Shall Be Provided. Top Of Legs Shall Be Joined Together With 25Mm Square Mild Steel Tube Of Wall Thickness 1.6Mm In Long And Short Sides. Two Short Stiffeners Of Same Size Shall Be Provided At 130Mm From Bottom Of Legs. One Long Stiffener Shall Also Be Provided To The Middle Of Short Stiffeners. Three Drawers Of Equal Size Shall Be Provided On The Right Hand Side Above The Stiffener At 130Mm High With Overall Size Of 350Mm Wide And 430Mm High And 410Mm Deep..The Top Of Table Shall Be Provided With Pre-Laminatedboard Of 18/19Mm Thick With Teak Veener Shade And 4Mm Thick Teak Wood Edging Alround The Table .Hard Rubber/Pvc Toes Shall Be Provided To The Legs.Locking Device Shall Be Provided To Drawers.Finish: All Steel Surfaces Exposed To View When Placed In Position Shall Be Paintedwith Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces.A Mark Of Mes Shall Also Be Provided On Top Left Corner Of Front Shutter With Visible Colour. Painting Shall Be Done With Spray Machine.Rest All As Per Drg. Total Quantity : 1

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	28-12-2021			30-12-2021

Refer document

Refer document

INR 35 Lakhs /-