Fixing Of Open Air Gym At Tikona Park, Panchvati, Alwar. 1 SURFING BOARDProviding and fixing of Surfing Board of size 1000mm (Length) x 600mm (Width) x 1400mm.(Height) fabricated with the main frame of 80mm NB shall be made from “C” class G.I. pipe.T, UIT Alwar-Rajasthan

Fixing Of Open Air Gym At Tikona Park, Panchvati, Alwar. 1 SURFING BOARDProviding and fixing of Surfing Board of size 1000mm (Length) x 600mm (Width) x 1400mm.(Height) fabricated with the main frame of 80mm NB shall be made from “C” class G.I. pipe.The bottom support shall be welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall bemade from center pipe of G.I. of 80NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Bushes shall be used of 70mm Outer Diameter with 5mm thickness. The footrests shall be made from high quality fiber reinforced plastic. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø35 mm SAE 8620 bright material. The bearing shall be used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly is of A34. The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with minimum 60 to 70 micron thickness. Design as per Sansun Model no. OG01 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 2 CROSS TRAINERProviding and fixing of Cross trainer of size 1320mm (Length) x 600mm (Width) x 1750mm. (Height) fabricated with the main frame Pipes of 80NB shall be made of “C” Class G.I and pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame shall be made up of 25NB “C” Class G.I. Pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipe of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe should be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm and CRC square pipes of 3mm thickness. To build structure bushes to be used which shall be made from M.S.seamless pipe of 60mm OD with 5 mm thickness. The footrests shall be made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35mm, 25mm, and 17mm shall be made up from SAE 8620 bright . The Bearings shall be used of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. A16 , A 24 mm circlips shall be used for assembly. Bolt M8X16 mm and NY lock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. Design as per Sansun Model no. OG02 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 3 THAI-CHI SPINNER (2 WHEEL)Providing and fixing of Thi-Chi spinner (2 Wheel) of size 700mm (Length) x 1000mm (Width) x 1280mm (Height) fabricated with a center pipe of 100NB shall be made up of “C” Class G.I. pipe. The handle movement round frame shall be made up from 25 NB “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø 25 mm of SAE8620 bright material. The bearing shall be used of “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile S.S. nut bolts shall be used for assembly. Foundation cover Closing Cap shall be made from FRP Material with 0.7 mm thickness. The cerclips used for assembly shall be of of A24 and A11. The nylon bush shall be used for handle knob. The powder coating shall be done with pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. Design as per Sansun Model no.OG05 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 4 SEATED PULLERProviding and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm & 10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG06 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 5 LEG PRESSProviding and fixing of Leg Press of size 1840mm (Length) x 360mm (Width) x 1560mm. (Height) fabricated with a center pipe of 100mm NB shall be made from “C” Class G.I. pipe. The Sleeve frame of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve should be disassembled from main frame. The bottom support shall be made up of M.S. round plate of Ø250 mm & 10mm thick. The remaining outer frame of 32NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80mm. NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. Seat & Back rest to be provided shall be made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The footrests shall be made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. The frame of footrests shall be made up of 25 NB “C” class G.I. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. To build structure bushes to be used which shall be made from M.S. seamless pipe of 50mm O.D. and 5mm thickness. The pins to be used shall be made up of Ø25 mm SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed Brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly are of A24 mm. The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. Design as per Sansun Model no. OG07 (Photo enclosed), all complete under directions of Engineer-in-charge.(The cement concrete and excavation work shall be paid separately). 6 SIT UP BOARD DOUBLEProviding and fixing of Sit up Board double of size 1760mm (Length) x 1140mm (Width) x 660mm (Height) fabricated with the main frame of 25mm NB shall be made from “C” Class GI pipe. FRP sheet of 3mm thickness shall be moulded on main frame. The remaining frame of the sit up board of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. The foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Design as per Sansun Model no. OG11 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 7 CHEST PRESSProviding and fixing of Chest Press of size 2000mm (Length) x 710mm (Width) x 2200mm. (Height) fabricated with the center pipe of 100NB shall be made up of “C” Class G.I. pipe. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes shall be made up from 25NB “C” class G.I. pipe. The handle frame shall be made up from 32NB “C” class G.I. pipe. To build structure bushes to be used which shall be made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap shall be made from FRP Material with 0.7 thickness. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 mm & A16mm. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG14 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 8 POMMEL HORSEProviding and fixing of Pommel Horse of size 2150mm (Length) x 800mm (Width) x 800mm. (Height) fabricated with the main frame of 80NB and 50NB shall be made from “C” Class G.I. pipe. The handle frame of 32NB shall be made from “C” Class G.I. pipe. 40mm x 40mm CRC square pipes frame shall be placed on the 25mm x 25mm x3mm M.S. L Angle with 60 x 10m thickness flat should be used for support. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to70 micron thickness. Design as per Sansun Model no. OG15 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 9 DOUBLE STANDING TWISTER Providing and fixing of Double Twister Standing of size 1500mm (Length) x 600mm (Width) x 1300mm. (Height) fabricated with a Center Pipe of 100NBshall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The bottom frame of 32NB shall be made from “C” class G.I. pipe. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB”C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size Ø300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35 mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed. Brand. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG17 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 10 STANDING SEATING TWISTERProviding and fixing of Seating & Standing Twister of size 1700mm (Length) x 540mm (Width) x 1250mm. (Height) fabricated with a Center Pipe of 100mm NB shall be made from “C” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm should be provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister of 32 NB, 50 NB, and 25 NBshall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe of 25mm NB. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The Pins to be used which shall be made up of Ø 35 mm SAE 8620 bright material. The bearings shall be made of of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness. Design as per Sansun Model no. OG18 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 11 CHEST CUM SHOULDER PRESSProviding and fixing of Chest Press Cum Seated Puller of size 2000mm (Length) x 710mm (Width) x 2200mm (Height) fabricated with the handle frame made up from 32NB “C” class G.I. pipe.To build structure bushes to be used which shall be made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipeshall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG).High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 & A16 The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG20 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 12 PUSH UP BARSProviding and fixing of Push Up Bars of size 1220mm (Length) x 550mm (Width) x 1700mm. (Height) fabricated with the main frame of 100 NB shall be made from “C” Class G.I. pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom.The handle frame of 25 NB shall be made from “C” Class G.I. pipe.The foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipeshall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.Closing Caps shall be made up of high quality Fiber reinforced Plastic material.Foundation cover Closing Cap shall be made from FRP Material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coatingshall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness. Design as per Sansun Model no. OG32 (Photo enclosed), all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 13 Supply and fixing of Instruction board of size 4x 6 made of digital vinyl print with gloss lamination & pasted on 3mm ACP sheet fixed over 2.0 mm thick MS sheet, framed on 32 mm dia MS pipe, supported on 50mm dia MS pipe which goes 600mm below ground level with hold fast including welding and painting.Design and drawing all complete under directions of Engineer-in-charge. (The cement concrete and excavation work shall be paid separately). 14 Annual Maintenance of all open air gym equipments fixed at Tikona Park, Panchvati, Alwar in Alwar for a period of 2 years (After one year free maintenance) including replacing of any or all damaged parts and running satisfactory in all respect.

INR 500 /-

Refer document

INR 4 Lakhs /-