Bids Are Invited For ( 1 ) Misc Hardware - Weld Mesh Panel With Accessories.. Weld Mesh Panels Should Produced By Electrical Resistance Welded Galvanized Wires And Subsequently Powder Coated As Per Below Spec.. Mesh Wire : Horizontal Wire, Dia 4.0 Mm ( + / - 0.05Mm ) : Vertical Wire, Dia 4.0 Mm ( + / -0.05Mm ) Mesh Size: Mesh Size Of 12.7 X 76.2 Mm Along Mesh ( Mesh Wire: Is 280 2006 ) . Panel Size : 2667X955mm Weight : 23.90 To 24.05 Kg. Metallic Coating : The Wires Should Be Galvanized And The Min Zinc Weight For The Horizontal And Vertical Wires Is Zinc Coated, 40 To 50 Gsm, Powder Coating : The Panels Are After Welding Subsequently Polyester Powder Coated, Layer Have A Thickness Of 60 To 80 Microns. Colour : Ral 6005Powder Coating Should Withstand 1000 Hours Of Salt Spray Test ( Type Test Certificate To Be Provided ) . Wire Tensile Strength : Min 550 N / Sq.Mm.Weld Strength: The Average Weld Shear Strength Of 4 Welds Taken At Random Shall Not Be Less Than50 % Of The Breaking Strength Of The Vertical Wire Note : Ref Drgs As Per Additional Terms And Conditions Of This Bid.Material: Ms. Mesh Wire: Dia:4Mm : Is 2802006. Coating : Is 4826 – 1979.Weld Mesh As Per : En 10223-7 ) , En 10245-1. , ( 2 ) Misc Hardware - Omega Clamp : Omega Clamps With Profile Cover Plate To Tighten The Mesh Panel Along The Post With 76Mm Dia, 35Mm Width, 3 Mm Thickness. ( Ms Strip As Per Is 1730 ) . Coating: Hot Dip Galvanized To Minimum 350 Gsm As Per Is 2629 / Is 4759 / Astm A 123.Note : Ref Drgs As Per Additional Terms And Conditions Of This Bid. , ( 3 ) Misc Hardware - Mushroom Head Bolt Nut With Washer : Each Clamps Will Be Supplied With A Pair Of Ss 304 Mushroom Headed , Square Necked Bolts And Security Nuts M8 X 50 ( Is:8535-1987 ) . Washer Specification Material: Ss 304, Od : 15.89Mm, Id : 8.38Mm, Thickness ; 2.04Mm. Note :- Additional 10% On Supplied Qty As Accessories Of All Nuts And Bolts And Clamps Will Be Provided To Crater For Any Losses / Damages As Directed By Buyer. , ( 4 ) Misc Hardware - Fence Post : Type : Circular Hollow Material : Ms Steel Tube ( Is 1161 ) . Dimentions : 76 Mm Dia, 3.2 Mm ( ( + / - 10% ) Thickness. Length : 3345 Mm ( + / - 5 % ) ( 2745 Mm Above Ground Level + 600 Mm Under The Ground Level ) . Coating : Hot Dip Galvanized To Minimum 350 Gsm As Per Is 2629 / Is 4759 / Astm A 123Followed By And Including Two Coats Of Synthetic Enamel Paint ( Bush Green Colour ) Over & Includingone Coat Of Red Oxide Primer. , ( 5 ) Misc Hardware - Straining Y-Arm For Supporting Top Ptcc: Material : Ms Angle Size : 50X50x5mm As Per Is 1852. Coating : Hot Dip Galvanized To Min 350 Gsm As Per Is 4759 / 2629, Length Of 1 ( One ) Arm Is 750Mm, Outer Dia Of63 Mm Of Sleeve Cap Will Be Fitted On The Top Of The Fence Post. , ( 6 ) Misc Hardware - Accessories For Fitting Y Arm:- Mushroom Head Bolt With Breakable Head Safety Nuts: Each Y Arm Shall Be Supplied With Two Sets Mush Room Headed Bolts With Security Nuts And Washers Material: Ss 304, Size : M8 X 120 Mm , ( 7 ) Misc Hardware - Intermediate Y-Arm For Supporting Top Ptcc: Material: Ms Angle Size :50X50x3mm As Per Is1852 Coating :Hot Dip Galvanized To Min 350 Gsm As Per Is 4759 / Is 2629.Length Of 1 ( One ) Arm Is750 Mm , Angle Between The Two Arms Is 120 Degree , With A Support Steel Strip Of 25X5 Mm ( Galvanized As Per Is 4759 ) And Fixed With Mushroom Head Bolt Andnut ( M8x25mm ) .Inner Dia 80Mm Of Cap Bolted On Top Of The Fence Post. 1 ( One ) Intermediated Y Arm Will Be Installed At Every Post Except The Posts With Straining Y Arms. , ( 8 ) Misc Hardware - Anchor Rod : 10 Mm Dia, 300Mm Long Gi Rod Tie With Fence Post At Bottom Using For Tie Wire. , ( 9 ) Misc Hardware - Punched Tape Concertina Coil ( Including Spike And Handle ) With 50 Turns And Dia 1050 Mm, Having A Core Wire Of High Carbon Spring Steel Of High Tensile Strength. The Punched Tape And Core Wire ( 2.6 ± 0.035 Mm Dia ) Are Electro Galvanised To Provide Protection Against Out Door Exposure. The Punched Tape Is Mechanically Crimped Over The Core Wire And Then Formed Into A Coil At Various Parts Of The Periphery Of The Coil; Steel Clips “Total 129 Nos Per Coil Equally Spaced” To Connect The Individual Turns Of The Coil To Each Other So That It Opens Up Like An Accordion. The Width Of Strip As 19 Mmand Spacing Of Blades 24.00 ± 0.5 Mm C / C. The Weight Of Each Coil Will Be 15.2 ± 5% Kgs Without Packing Material And Coil Length 15 Mtr When Opened Up With An Effective Height Of 915 Mm. Each Coil Woundwith Bituminised Hessiancloth For Providingprotective Packing.Punched Tape Concertina Coil 1A Shall Confirm To Cqa, Ee, Pune Specifications No : Cqae / 5660 / 1602 / A And Controller Of Qality Assurance Of Engg. Equipment, Pune. Drawing No Img-0112 / B ( Sheet 1 Of 2 ) , Imga-0112 / C ( Sheet 2 Of 2 ) , Impd-1817 / B, Impd-1820, Impd-1821 / B And Impd-1822 / B. , ( 10 ) Misc Hardware - Galvanised Steel Barbed Wire, Isi Markeda-5 Designation For Galvanised Steel Barbed Wire For Fencing Shall Conform To Is 278 – 1978. The Barbed Wire Shall Consist Of Two Line Wire 2.24 Mm Dia ( Tensile Strength 390 – 590 N / Mm2 ) Standminimum Breaking Load Of Complete Barbed Wire 3Kn ) , One Or Both Containing 2.00 Mm Dia Barbs At 75 Mm Centre To Centre And Weighing97 To 106 Kg Per Km. The Barbs Shall Have A Length Of Not Less Than 13 Mm And Not More Than 18 Mm. The Line And Point Wires Shall Be Circular In Section, Free From Scales And Other Defects And Shall Be Uniformly Galvanised. The Line Wire Shall Be In Continuous Length And Shall Not Contain Any Welds Other Than Those In The Rod Before It Is Drawn. The Galvanising Shall Conform To The Requirement As Laid Down For Light – Coated Wire Of Is 4826 – 1968 `Specification For Galvanised Coating On Round Steel Wires. Barbing Wire ( Line ) Shall Be Hard Type Heavy Coated ( 230 Gm / Sqm ) And Barbing Wire ( Point ) Shall Be Hard Type Light Coated ( 70 Gm / Sq M ) . The Galvanised Barbed Wire Will Be In Bundleswill Be Packed In Hessian Cloth, The Bundles Should Be Strong Enough To Withstand Rough Handling During Transportation. Each Bundle Of Barbed Wire Having Weight Without Packing Materials Minimum 25 To 30 Kgs Or Average Weight 28 Kgs And Length Of Each Bundle Is 168 Mtr ( 550 Feet ) .Every Reel Of Barbed Wire Shall Be Marked Legibly With Bis Standard Make The Name Of Manufacturer, The Type Of Barbed Wire, The Diameter Of The Line And Point Wires, Barb Spacing And Length And / Or Mass Of The Reel.Strands : Single ( 6 Row ) .Note For Item Ser No 1 To 10 :- All Specifications For Item Ser No 1 To 10 Above Of This Boq Shall Be Provided As Per Hq 15 Corps, Engr Branch Drg Nos 3534 / Acf / 001 / Sheets, 01 To 03 Dt 01 Jun 2017And3534 / Acf / Lc / 002 / Sheets 02 To 03 Dt 10 Apr 2018 ( Total Sheet - 05 Nos Drawing ) As Uploaded In Additionalterms And Conditions Of This Bid. , ( 11 ) Misc Hardware - Main Gate. Mild Steel Gate 9.0 M Wide And 2.1M High, In Two Shutter Parts As Per Drawing No Main Gate / 01 / Owc Dt 24 May 2019 Attached As Sketch U As Per Drawings In Additional Terms And Conditions Of This Bid. The Main Specificaiton Of Steel Gate As Under:- ( A ) Ismb 175X 85Mm, 3.03M Long Provided For Gate Pillar / Column -Qty -02 Nos. ( B ) Shutter Frame Work- Qty-02 Nos. Each Shutter Haivng Size 4.50Mx 2.10M With Specification Given Below:- ( I ) Outer Frame Made Of Angle 65X65x6mm. ( Ii ) Back Side Cross Bracing Made Of Angle 40X40x5mm. ( Iii ) Middle Lock Rail Made Of Angle 50X50x5mm Thick ( Iv ) Vertical Spike Of 10Mm Square Bar, 2.28 Long With Pointed End As Specified In Drawing, And Distance Between Bars @ 100Mm Center To Centre. ( V ) Necessary Hold Fast Arrangement Shalll Be Made As Per Drawing Att And As Directed By Buyer. ( V ) Necessary Suitable Locking Arrangment Shall Be Madeas Per Drawing Att And As Directed By Buyer. ( Vi ) Provide A Small Door Openingof Size 1.00M X 0.6M Including Necessary Hings, Locking Bolts Complete As Per Drawaing Attached And As Directed By Buyer. ( Vii ) Applying Of Two Coats Of Synthetic Enamel Paint Over And Including One Coat Of Red Oxide Primer To All Steel Component Complete. Note:-1. Rate For Carry Out Necessary Welding Work For Making Steel Gate Frame Work Are Including In Quoted Rate By Vendors.2.Theismb ( Gate Pillars ) Shall Be Embedded In Pcc 1:2:4 , B1 ( 20Mm Graded Aggregate For Foundation Of Size 450 X 450 X 750Mm. , ( 12 ) Construction Materials - Cement Opc 43 Grade In Bag Of 50 Kg Each Bagsconforming To Is-8112-1989 , ( 13 ) Construction Materials - Natural / M Sand Conforming To Is 383-1970 ( Specifications For Coarse And Fine Aggregates.Free From, Hard, Durable, Clean And Shall Not Contain Clay And Impurities Such Iron Pyrites, Alkalies, Salt, Coal, Mica, Shale Or Similar Laminates Or Other Materials Exceeding The Specified Limits In Is Code Aggregates For Concrete. , ( 14 ) Construction Materials - Stone Aggregate 20Mm.Stone Aggregate To Be Crushed Rock Or Gravel 20Mm Graded Confirming To Is 383-1970 ( Second Revision ) And Shall Consist Or Angular Fragments And Shall Be Clean, Hard, Tough, Durable And Of Uniform Quality Through Out , ( 15 ) Construction Materials - Stone Aggregate 40Mm.Stone Aggregate To Be Crushed Rock Or Gravel 40Mm Graded Confirming To Is 383-1970 ( Second Revision ) And Shall Consist Of Angular Fragments And Shall Be Clean, Hard, Tough, Durable And Of Uniform Quality Through Out. , ( 16 ) Construction Materials - Quick Setting Compound ( Rapidite ) ( Make Acclerex / Cico / Fosroc , ( 17 ) Construction Materials - Ms Binding Wire ( Annealed ) Not Less Than 0.9Mm Dia Conforming To Is 270-1978 , ( 18 ) Tools - Electrical Hand Gloves Of High Tear Resistance 33 Kv Complete As Per Specifications. , ( 19 ) Tools - Spanner Set Ojde No 6 To 32. , ( 20 ) Tools - Cutting Plier Large 157 Mm Long. , ( 21 ) Tools - Screw Driver Set 812 With Neon Bulb. , ( 22 ) Tools - Clamp Meter. , ( 23 ) Tools - Adaptor For Drillig Machine 6 Mm . , ( 24 ) Tools - Adaptor For Drillig Machine 8 Mm . Total Quantity : 1
