Repairs To Wooden And Steel Furniture For Kasauli Under Ge Kasauli-2 REPAIR TO CHARPOYGI PIPE 32MM AND CONVERSION/ REPLACEMENT WITH PLY TOP 3 Long rail;- Re-threading and fixing with elbow after removing and cutting the long railall as shown on drg and , KASAULI-Himachal Pradesh

Repairs To Wooden And Steel Furniture For Kasauli Under Ge Kasauli-2 REPAIR TO CHARPOYGI PIPE 32MM AND CONVERSION/ REPLACEMENT WITH PLY TOP 3 Long rail;- Re-threading and fixing with elbow after removing and cutting the long railall as shown on drg and as directed. 4 Short rail :- All as per description at ser No1.01 above but to short rail. 5 Legs :-All as per description at ser No1.01 above but to legs. 6 S & F long rail to charpoy GI made out of 32mm dia GI pipe medium grade conf to IS:1239 Part-Iof lengh 1.9 mtrafter removing the old one. 7 Cutting , threading and fixing of short rails obtained from long rails at ser No 1.04 above as per drg after removing the old one. 8 Cutting , threading and fixing of Legs obtained from short rails at ser No 1.05 above as per drawings after removing exising unservicable legs. 9 S & F of check nut 6mm thick 32mm dia GI to the long rails after removing the old UNSV chek nuts. 10 S & F32mm GI elbow 3 way medium gde ISI marked after removing the old UNSV Elbow. 11 S&F ply wood 12mm thick BWR type size 1980X930 after tightining of frame all as specefied with provision of flat iron of size 40X6mm,900mm long 2 Nos with 65mm long 6mm dia nuts and bolts 8 Nos with washers after drilling complete all as specified after removing the old unservicable nylon newar from charpoy. 12 M & L forwelding to steel frames of furniture articles such as chairCB steel with arms,chair CB steel without out arms, chair verandah, table office clerk steel, form with out back, steel almirah, Table dining ORs, Locker bed side steel etc, including fixing of parts in proper position by preparing the old welded surfaces. welding shall be done through gas welding, the thickness of the metal to be welded n.exe 16 gauge. Length of welding n.exe. 25mm in each point, all as directed. 13 Repair to Chair CBA steel 14 S&F MS flat iron of size 500X20X3mm with gas welding to chair 2 nos under the seat and joining both ends in each chair CBA steel duly painted with one coat of synthetic inamelled paint OG shade over a coat red oxide 15 Seat frame made out of 2nd class hard wood (Hollock) of dimension as shown on drg duly polished, woven with 2mm wide plastic cane in true Godrej pattern to chair CBA Steel 16 Back frame made out of 2nd class hard wood (Hollock) of dimension as shown on drg duly polished, woven with 2mm wide plastic cane in true Godrej pattern to chair CBA steel 17 S&F arms Made out of 2nd class hard wood (Hollock) of dimension as shown on drg to Chair CBA steel. 18 M & L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete ofcolour/shade as directed by Engr-in-charge and as required :- 19 Repair to Chair CB Steel 20 S&F MS flat iron of size 500X20X3mm with gas welding to chair 2 nos under the seat and joining both ends in each chair CB steel with out arms steel duly painted with one coat of synthetic inamelled paint OG shade over a coat red oxide 21 Seat frame made out of 2nd class hard wood (Hollock) of dimension as shown on drg duly polished, woven with 2mm wide plastic cane in true Godrej pattern to chair CB Steel without arms 22 Back frame made out of 2nd class hard wood (Hollock) of dimension as shown on drg duly polished, woven with 2mm wide plastic cane in true Godrej pattern to chair CB steel with out arms 23 M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete ofcolour/shade as directed by Engr-in-charge and as required. 24 REPAIR TO ALMIRAH STEEL MEDIUM WITH SHELVES 25 Removing unserviceable shelves of almirah Medium steel & material & labour for providing new shelves made out of PBI sheet 1mm thick cold rolled duly painted with spray paint synthetic enamelled OG/smoke grey over a coat of red oxide primer after preparation of surface & fixing the same with MS clamps,nuts & bolts as shown on drg. 26 Removing of unserviceable locks, supply & fixing of new lock of approved quality as required having 3 way locking device & duplicate key all as specified in drg. 27 Removing of unserviceable Tala plates, supply & fixing of new Tala plate of approved quality as per drawings. 28 S&F of CP steel handle & to make the locking device in proper function as specified and shown on drg. 29 S&F of legs(foot rest) made out of 18G MS sheetto almirah medium steel as per drg after removing the old one 30 S&F of MS clamps made out of suitable size mild steel flat iron withsuitable nuts & bolts as specified in drg. 31 Removing unserviceable moving rod of almirah medium steel and S & F new moving rod 8mm dia of required length as per drg including making it functional after painting with OG Paint synthetic enameled over a coat of primer. 32 M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete ofcolour/shade as directed by Engr-in-charge and as required :- 33 REPAIR TO ALMIRAH STEEL LARGE WITH SHELVES 34 Removing unserviceable shelves of almirah large steel & material & labour for providing new shelves made out of PBI sheet 1mm thick cold rolled duly painted with spray paint synthetic enamelled OG/smoke grey over a coat of red oxide primer after preparation of surface & fixing the same with MS clamps,nuts & bolts as shown on drg. 35 Removing of unserviceable locks, supply & fixing of new lock of approved quality as required having 3 way locking device & duplicate key all as specified in drg. 36 Removing of unserviceable Tala plates, supply & fixing of new Tala plate of approved quality as per drg. 37 S&F of CP steel handle & to make the locking device in proper function as specified and shown on drg. 38 S&Fof legs foot rest made out of 18G MS sheetto almirah med steel as per drg after removing the old. 39 S&F of MS clamps made out of suitable size MS flat iron with suitable nuts & bolts as specified in drg. 40 Removing unsv moving rod of almirah large steel and S&F new moving rod 8mm dia of required length as per drg including making it functional after painting with OG Paint over a coat of primer. 41 M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete ofcolour/ shade as directed by Engr-in-charge and as required. 42 REPAIR TO CHAIR VERANDAH 43 M&L for re-canning of chair verandah with cane plastic half round4mmwide in mattpatternsuperior quality as shown on drg and as directe. 44 M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete and colour/shade as directed by Engr-in-charge and as required. 45 PAINTING TO STEEL FURNITURE( INTERNALLY & EXTERNALLY):- 46 M&L for preparation of old painting surfaces of any description width or girth including cleaning/scraping old painted surfaces with blow lamp etc denting & filling the depression with putty and rubbing the surface there after andpainting with one coat of synthetic enamel paint by spray machine to steel items complete and colour/shade as directed by Engr-in-charge and as required. 47 INTERNALLY & EXTERNALLY 48 Almirah Large steel with shelves 49 Almirahmedium steel with shelves 50 Locker bed side steel 51 Table office clk steel 52 EXTERNALLY 53 Chair CB steel with arms 54 Chair verandah 55 Teapoy verandah 56 Book shelf open large steel 57 REPLACEMENT OF CUSHION FOR SOFA SET 4/5 SEATER 58 M&Lin replacement of foam cushion size 560x530x100mm, 40 density, duly coveredall over with tapestry cloth superior qualitynot less than Rs 350/- per R/M as approved.A suitable chain with hook and runner of approved quality one side of the cushion will be provided of the required length as directed by Engineer-in charge. 59 REPAIR TO CHAIR EASY : S & F of following components of chair easy made out of well seasoned sheesham wood all as per drg after removing the old one. 60 Front leg 61 Rear leg 62 Side rail duly holed (Distance of 12.5 mm from one hole to another) 63 Front rail duly holed (Distance of 12.5 mm from one hole to another) 64 Back rail duly holed (Distance of 12.5 mm from one hole to another) 65 Front support rail 66 Back support rail 67 Arms 68 Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 69 REPAIR TO CHAIR WRITING : S&F of following components of chair Writing made out of well seasoned sheesham wood all as per drg after removing the old one. 70 Front leg 71 Rear leg 72 Side rail duly holed (Distance of 12.5 mm from one hole to another) 73 Front rail duly holed (Distance of 12.5 mm from one hole to another) 74 Back rail duly holed (Distance of 12.5 mm from one hole to another) 75 Long Stiffner 76 Back support rail 77 Arms 78 Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 79 REPAIR TO CHAIR DINING : S&F of following components of chair Diningmade out of well seasoned sheesham wood all as per drg after removing the old one. 80 Front leg 81 Rear leg 82 Side rail duly holed (Distance of 12.5 mm from one hole to another) 83 Front rail duly holed (Distance of 12.5 mm from one hole to another) 84 Back rail duly holed (Distance of 12.5 mm from one hole to another) 85 Long Stiffner 86 Back support rail 87 Preparation of surface by removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 88 M&L for re-canning to all types of chairs, chair dinning, writing, easy, CBA, CBB, easy NF, stool dressing and bin soiled etc with cane plastic 2mm wide half round with border of 3mm wide in white colour as approved in true godrej pattern as shown in drg after removing the old one. 89 Repair to Peg Table 90 Removing the unserviceable leg and providng the new leg made out of 1st class sheesham wood seasoned of size 30x50x362mm high and fixing the same in its original position as per drg. 91 Removing the old broken top rail and providing the new top rail made out of 1st class hardwood sheesham of size 20x40x380mm and fixing the same in its original position as per drg. 92 S&F in replacement of table top for Peg tableafter removingthe old unserviceable top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 93 Preparation of surface by Removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 94 Repair to Table Centre 95 Removing unseviceable leg and providing new leg made out of 1st class hardwood sheesham of size 60x30x356 mm and fixing the same in its original position as per drg. 96 Removing old broken top rail and providing the new top rail made out of 1st class hardwood sheesham of size20x50x900mm and fixing the same in its original position as per drg. 97 S&Fin replacement of table top for table centre after removingthe old unserviceable top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 98 Preparation of surface by Removing of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 99 Repair to Table Dining 6 person 100 Removing unserviceable leg and providing new leg of size 75x40x722mm high and shape made out of 1st class well seasoned hardwood sheesham and fixing the same in its original position as per drg. 101 Removing the unserviceable top rail long and providing the new top rail of size 25x100x1500mm and shape made out of 1st class hardwood well seasoned sheesham and fixing the same in its original position as per drg. 102 Removing old broken top rail short and providing the new top rail made out of 1st class hardwood sheesham and fixing the same in its original position as per drg. 103 S&Fin replacement of table top for table dining six person after removingthe old unsv top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 104 Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 105 Repair to Table Dining 8 person 106 Removing unserviceable leg and providing new leg of size 75x40x722mm high and shape made out of 1st class well seasoned hardwood sheesham and fixing the same in its original position as per drg. 107 Removing the unserviceable top rail long and providing the new top rail of size 25x100x1500mm and shape made out of 1st class hardwood well seasoned sheesham and fixing the same in its original position as per drg. 108 Removing old broken top rail and providing the new top rail made out of 1st class hardwood sheesham of size 1500x900mm and fixing the same in its original position as per drg. 109 S&Fin replacement of table top for table dining eight person after removingthe old unsv top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 110 Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 111 Repair to Table 3x2 with drawer 112 Removing unserviceable leg and providing new leg made out of 1st class well seasoned hardwood sheesham and fixing the same in its original position as per drg. 113 Removing the unserviceable top rail long and providing the new top rail made out of 1st class hardwood well seasoned sheesham and fixing the same in its original position as per drg. 114 Removing old broken top rail short and providing the new top rail made out of 1st class hardwood sheesham and fixing the same in its original position as per drg. 115 S&F in replacement of table top forTable 3 x 2 with drawer after removingthe old unsv top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 116 Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 117 Repair to Table Dressing Ladies 118 Removing unserviceable legs and providing the legs of size 150x45x45mm made out of well seasoned sheesham wood and fixing the same in its original position as per drg. 119 Removing unserviceable stiffener and providing the new one of size 235x40x25 mm made out of 1st class well seasoned sheesham wood and fixing the same in its original position as per drg. 120 Removing unserviceable top and providing/fixing the new one made out of 18mm thick pre-laminated particle board of size 900x380mm with 4mm thick sheesham wood beading on front side and fixing the same in its original position. 121 Remove the ply wood from the back of the mirror and providing the new one made out of 6mm Green ply BWR commercial and fixing the same in its original position as per drg. 122 Remove the unserviceable broken mirror and providing the new one of size 1220x365x5.5mm thick Make-Golden Fish/Swastik or as approved by Engineer-in-Charge and fixing the same in its original position. 123 S&F in replacement of table top for table dressing ladies after removingthe old unserviceable top made out of 19mm thick pre-laminated particle board one side sheesham faced and other side white balancing confirming to IS-3097including sheesham wood beeding 6mm thick fitted all around duly french polished as shown in Drg and as directed by Engineer -in-charge. 124 Preparation of surface by remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. 125 Repair to Bed Hard with Ply Top : Dismantling of old unserviceable components and S & F of new components made out ofwell seasoned sheesham wood properly planed all as shown in drg :- 126 S & F Long rail size 1980x100x40mm 127 S & F Short rail size 840x100x40mm 128 S & F Stiffner to support ply top of size 835x50x40mm 129 S&F of head side board of bed newar/bed ply top duly fixed with legs of shisham wood including dismantling ofUNSV Compoment all as specified and shown on drg. FD-245/246 130 S&F of foot side board of bed newar/bed ply top duly fixed with legs of shisham wood including dismantling ofUNSV Compoment all as specified and shown on drg. FD-245/247 131 S&F of 3mm thick sheesham face ply wood BWR gde with head less nailsto both sides to the following including sheesham wood beading 6mm thick all around after taking out old one. 132 (i) Head board size 900x442mm 133 (ii)Foot board size 900x230mm 134 S&F ply wood of size 1830x865x12mm in one pieceBWPISI marked to bed hard fixing with 30mm screw wood steel as shown on drg. 135 S&FMS flat ironclamp size 200x35x6mmto be fixed with six Nos of screw wood steel as shown on drg duly painted with paint enamelledblack. 136 POLISHING TO WOODEN FURNITURE : M&L for preparation of old polished surfaces of any descreption width or girth including cleaning , removing oily spots, ink dots etc and polishing with french polish for glossy finish to the entire satisfaction of Engr -in- charge the tint of polish shall be exactly same as of existing polish colourof furniture or as approved by Engr-in-charge. 137 Almirah large with shelf 138 Almirah Mediumwith shelf 139 Bed hard with ply top 140 Book case small 141 Bin soiled linen 142 Chair dining 143 Chair writing 144 Chair easy 145 Chair CBA 146 Chair wooden bottom 147 Sofa set 5 seater 148 Locker bed side(Internal & External) 149 Table peg 150 Teapoy 151 Table bed side 152 Table office officer wooden 153 Table office clkwooden 154 Table writing 155 Table centre 156 Table dining 8 pers 157 Table 3x2 with drawer 158 Table 3x2 without drawer 159 Side board

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	11-11-2021	Bid Auto Extn Corrigendum	Bid Auto Extn Corrigendum	18-11-2021

INR 500 /-

INR 12000.0 /-

INR 6 Lakhs /-