Bids Are Invited For Lcr Meter (Digital) Handheld - Measurement Function :Test Parameter:L - Q, C - D, R - Q, Z - Q , Z – D, Circuit :Series And Parallelmath Function:Deviation And Percent And Ranging Mode:Auto, Hold • Trigger Mode :Internal, • Correction Function :Open / Short Multi - Frequency Zeroing, Measurement Terminals:Five Terminals, • Display Mode :Direct, ?%, ? Abs, • Display :20 X 2 Characters Lcd With Back – Light, Test Signal : Signal Frequency :100Hz, 120Hz, 1Khz, • Output Impedance :Varied With Different Range, • Signal Level:0.3Vrms, Measurement Display Range : Izi, R :0.001O-99.999Mo, C :0.1Pf - 99999Μf, L :0.1H - 9999H,D :0.0001-9999,Q :0.0001-9999 , 70 Mhz Mixed Signal Oscilloscope ( 4 Analog + 16 Digital Channel ) - 70Mhz 4 Analog Channel And 16 Digitalchannelsoscilloscope,The Oscilloscope Should Support 1Gsa/S Sampling For Analog Channel And 1Gsa/S / 500Msa/S For Digital Channels , Memory Depth Should Be More Than 20 Mpts, Vertical Rage 1Mv/Div -10V / Div, Horizontal Range 5Ns/Div To 50 S/Div, It Should Have Built In Two Channel 25Mhz Source With 14 Bit Vertical Resolution And 200Msa/S Sample Rate , It Should Also Have At Least 26 Nos Automatic Measurements And 6 Bits Hardware Counter, Advance Serial Bus Trigger And Decoding Functions Including Rs232/Uart, I2c And Spi, Multi Triggering Facility, Math Functions Like A+B, A-B, A×B, A/B, Fft, A&&B, A||B, A^B, !A, Intg, Diff, Sqrt, Lg, Ln, Exp, Abs.7 Inches Wvga Tft Display, Computer Interface Usb Host And Device And Lan. , Multi Function Test & Measuring Tool For Field Applications And Testing Compatible With Laptop - 300Mhz 2 Channel Oscilloscope:Function & Arbitrary Waveform Generator With Sine 50Mhz, Square 15Mhz, Triangle 100Khz, Am-Fm Modulation, 300Mhz Spectrum Analyzer, Frequency & Phase Meter, Pattern Generator, 16 Channel Logic Analyzerdata Recorder, Usb Powered, Interactive Virtual Graphical User Interface Software Separate Window For Every Instrument, Technical Specifications (Oscilloscope):• Bandwidth: 300Mhz, Rise Time : 2.5 Ns, Input Channels : 2,Vertical Resolution: 8 Bits, Input Characteristics: 1 M In Parallel With 5 Pf, Input Type : Single–Ended, Bnc Connector, Input Coupling : Software Selectable Ac/Dc, Sampling Rate (Each Channel), Real / Per Channel: 125 Mhz, Effective / Per Channel: 100 Ghz, Vertical Sensitivity, 1X Probe : 2 Mv - 2 V / Div, 10X Probe : 220 Mv - 20 V / Div, Buffer Memory Sizeone Channel In Use: 1024 Kb, Two Channels In Use: 512 Kb, Time Base : 1 Ns/Div To 100 Ms/Div, Trigger Modes : Normal, Auto, One Shot, Single, Ch1, Ch2, Trigger Threshold • Basic Triggers: External/ Ch1/ Ch2/ Alternative Rising Edge/ Falling Edge/ Auto/ Normal/ Single,• External Trigger Bandwidth : 300 Mhz , Digitalictrainer - Technical Specifications:• Size Of Breadboard :172.5 Mm X 68Mm,• Dc Supply:+5 V, 500 Ma,• Clock Frequency :1 Hz, 100 Hz, 1 Khz, 100 Khz,• Amplitude:3.3V (Ttl),• Duty Cycle:50 %, Ttl Output,• Pulsar Switches :2 Nos.,• Graphical Lcd :128 X 64 Dots,• Data Switches :8 Nos. (Toggle Switches For Both Ttl Modes),• Led Display:8 Nos. (Ttl),Seven Segment Display:3 Nos.,• Main Supply :100V - 240V Ac, 50Hzthe Training Should Include Online Single User Classroom / Laboratory Teaching, Learning And Simulation Software Module On Digital Electronic:The Content Should Designed By Using Platforms Like Visual Basic, Dot Net, Flash Etc. The Module Should Comprises Simulations, Animations, Videos, Graphs, Charts, Along With Mandatory Rich Content And Theory To Understand Fundamental Concepts, Interactive Learning Objects, Faq, Mcq, Notes And Questions Bank.Etc Of Digital Electronic. Digital Electronic To Understand Fundamental Concept Of Measuring Instruments: Oscilloscope, Multimeter, Digital Electronics, Number Systems, Codes, Complements, Boolean Algebra, Logic Gates, Arithmetic Circuits: Adder, Subtractor, Combinational Circuits: Multiplexer, De Multiplexer, Encoder, Decoder, Sequential Circuits (Flip-Flops): S-R Flip-Flop, D Flip-Flop, J-K Flip-Flop, T Flip-Flop, Registers And Counters. , Smd Technology Kit - It Should Have Following Technical Specifications:• Smd Identification Board• The User Should Familiarized With Different Smd Components Resistors, Capacitors, Inductors, Diodes, Transistors & Ic’S Packages.• Proto Boards Are Special Pcb’S With Readymade Solder Pads For Various Smd Components & Ic’S, Which Makes The Soldering Much Easy. It Includes Through Hole, Sop, Chip Scale Package Proto Boards.• Smd Soldering Jig• Smd Soldering Iron For Soldering Practice.• A Variable Temperature Controlled Soldering Iron Is Supplied With Lead.• Smd Components Are Supplied For Solder Practice .I.E., Resistor, Capacitor, Diode, Transistors• Tweezers For Holding & Placing Of Smd Components. , Electronic Circuit Simulationsoftware With Five User Licenses - The Software Should Have Facility Of Circuit Simulation And Pcb Design Of Analog, Digital And Mixed Electronic Circuits With Their Pcb Layouts. All User Perpetual License Of The Software Should Support Either The Digital Online Access, And Simulation Or The License Protection Should Be Supported Through Usb Hardware Dongle And Have Facility To Upgrade In Future. Pcb Design: Create Multilayer Pcb Layouts Of Circuits, With Automatically Placed And Routed Components. All Components In Software Should Be “Pcb-Ready” And Have Associated Footprints Which User Can Review And Change On A Component Spreadsheet. It Should Also Have 3D Capability To Preview The Physical Parts Already On The Schematic Diagram With Run Time Animation In 2D And 3D View, Visualizations Of Pcb Design With Enclosures In 3D, 3D Printer Support, Importing Footprints In 2D And 3D In Industry Standard Formats. Pcb Design Software Should Support Both G Code And Gerber Generation Of The Data. , Analog Component Trainerwith Seven Basic Modulesbreadboard Forcircuit Design With Necessary Dc /Ac Powersupply: Sine, Square, Trianglemodulating Signalgenerator And Simulationsoftware - It Should Have Following Technical Specifications:Dc Power Supplies :+ 5V, 1 A (Fixed) + 12V, 500 Ma (Fixed) -12V, 500 Ma (Fixed) + 12V, 500 Ma (Variable) -12V, 500 Ma (Variable)Ac Supply:9V-0V-9V, 500Mabreadboard:Breadboard For Making Various Circuits And Testing Them. External Components/Ic Can Be Fitted Conveniently.Function Generator :Operating Modes Sine, Square And Triangular. Frequency Range 1 Hz To 100 Khz.Volt/Current/Frequency :Voltage Range +12V To -12V Dcmeasurementcurrent Range 0 To 500Ma Dc Frequency Range Dc To 100Khz (All With Respect To Ground)Display:Lcdpc Interface:Acquisition From Two Analog Input Channels (Max. Input 1Volt)Continuity Tester :For Testing The Continuity. Provided With Beeper Sound.Power Supply:110-220 V, 50Hz.The Training Should Include Online Single User Classroom / Laboratory Teaching, Learning And Simulation Software Module On Analog Electronic Total Quantity : 1
