|
| 1 | Demolishing cement concrete manually/ by mechanical means includingdisposal of material within 50 metre lead as per direction of Engineer- in- charge : Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 2 | Demolishing cement concrete manually/ by mechanical means includingdisposal of material within 50 metre lead as per direction of Engineer- in- charge :Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 3 | Dismantling steel work in single sections including dismemberingand stacking within 50 metres lead in:Channels, angles, tees and flats |
| 4 | Dismantling stone slab roofing over wooden karries or R.C.C. battens (dismantling karries and battens to be paid for separately), including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 5 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 6 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V Cement mortar 1:4 (1 cement :4 coarse sand) |
| 9 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 10 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners,all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6mm for diagonal braces and central cross piece |
| 11 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cementconcrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 12 | Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C.battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : Red sand stone slab 40 to 50 mmthick |
| 13 | Laying slabs of all thickness for roofing in cement mortar 1:4 (1 cement : 4 coarse sand) over wooden karries or RS Joists/T-iron(karries and RS Joists/T-iron to be paid for separately) including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ). Stone slabs shall be provided by the department free of cost at site of work. |
| 14 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate |
| 15 | Neat cement punning |
| 16 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 17 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st qualityconforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matchingpigments etc., complete |
| 18 | 12 mm cement plaster of mix: 1:6 (1 cement : 6 fine sand) |
| 19 | 15 mm cement plaster on the rough side of single or half brickwall of mix: 1:6 (1 cement : 6 fine sand) |
| 20 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests |
| 21 | Deduct for not providing hinges in doors, windows or clerestory window shutters with : ISI marked M.S. pressed butt hinges bright finished of required size For 2nd class teak wood and other class of wood shutters |
| 22 | Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc. complete : 150 X 10 mm |
| 23 | Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed of required colour and shade, with necessary screws bolts, nut and washers etc. complete. |
| 24 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100 mm |
| 25 | 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. |
| 26 | Providing and fixing soil, waste and vent pipes 100 mm dia. Sand cast iron S & S pipe as per IS: 1729 |
| 27 | Providing and filling the joints with spun yarn cement, slurry andcement mortar 1:2 ( 1 cement: 2 fine sand) in S.C.I/C.I pipes 100 mm dia pipe |
| 28 | Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 29 | Providing and fixing PTMT stop cock of approved quality and colour. 20 ‘mm nominal bore, 89 mm long, weighing not less than88 gms |
| 30 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Circulsr Tank |
| 31 | Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 100 mm diameter |
| 32 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diameter metre |
| 33 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe metre |
| 34 | Providing and laying dry brick aggregate 40mm nominal size in foundation and plinth or under floors at all levels including spreading and ramming in layers as directed by Engineer-in-charge. |
| 35 | Disposal of building rubbish / malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 36 | Extra for every additional lead of 50m or part thereof beyond first 50m upto 9 such additional leads Lime, moorum building rubbish (13.49x9) |
| 37 | Deduct for not Providing and fixing P.V.C. low level flushing cistern with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings and fixturescomplete.10 litre capacity - White |
| 38 | Add 22.69% as per GNCTD order |
| 39 | Deduct 9.50% as per GNCTD order . |
| 40 | Less for Salvage Value (Steel) |
