| 1 | 1 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and as directed. | | 560 | Sqm |
|---|
| 2 | 2 | Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets | | 200 | Sqm |
|---|
| 3 | 3 | Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. | | 47.5 | Cum |
|---|
| 4 | 4 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. | | 2.08 | Cum |
|---|
| 5 | 5 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge. | | 465 | Sqm |
|---|
| 6 | 6 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, fascias, fins and similar works. | | 1 | Cum |
|---|
| 7 | 7 | M&L for reinforced cement concrete (nominal mix) 1:2 :4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately. | | 1 | Cum |
|---|
| 8 | 8 | S&F TMT MS bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified . | | 150 | Kg |
|---|
| 9 | 9 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete. | | 10 | Sqm |
|---|
| 10 | 10 | Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed. | | 600 | Sqm |
|---|
| 11 | 11 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all specified and as directed | | 2 | Qtl |
|---|
| 12 | 12 | S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0. | | 200 | Kg |
|---|
| 13 | 13 | M&L Pressure grouting of honey combed concrete with cement slurry by adding CEBEX 100 or equivalent @ 255 gms/50 Kg of cement.\n | | 50 | Per Nozzle |
|---|
| 14 | 14 | M&L for PCC 1:5:10 type E-2 using 40 mm graded brick aggregate as in filling of sunken portion etc complete all as specified and directed. | | 20 | Cum |
|---|
| 15 | 15 | M&L for 25mm thick cement cocrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate mixed with WPC (in proportion as per manufacturers instruction) as in bedding in sunken portion of slab complete all as specified and directed | | 40 | Sqm |
|---|
| 16 | 16 | M&L for rendering 10mm thick plaster im cement mortar (1:3) mixed with water proofing admixer (in proportion as per manufactures instruction) as in sunken portion, finished the surfaces even and smooth without using extra cement complete all as specified and directed. | | 40 | Sqm |
|---|
| 17 | 17 | M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed. | | 1 | Cum |
|---|
| 18 | 18 | M & L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete . | | 25 | Cum |
|---|
| 19 | 19 | M&L for plain cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as in roof kerb complete all as specified and directed. | | 1.5 | Cum |
|---|
| 20 | 20 | Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. | | 1.5 | Cum |
|---|
| 21 | 21 | M&L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 | | 5 | Sqm |
|---|
| 22 | 22 | Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m. | | 900 | Sqm |
|---|
| 23 | 23 | M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed. | | 900 | Sqm |
|---|
| 24 | 24 | M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following - | | 0.01 | kj |
|---|
| 25 | 24.01 | Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.25 kg/Sqm on top of dry surface of finished cement mortar plaster. | | 900 | Sqm |
|---|
| 26 | 24.02 | One layer of APP based polymeric water proofing membrane of weight not less than 3.5kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame. | | 900 | Sqm |
|---|
| 27 | 24.03 | Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm. | | 900 | Sqm |
|---|
| 28 | 24.04 | M&L Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m on roof surfaces. | | 900 | Sqm |
|---|
| 29 | 25 | S&F pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified . | | 500 | Sqm |
|---|
| 30 | 26 | S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified. | | 60 | Sqm |
|---|
| 31 | 27 | S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified. | | 200 | Sqm |
|---|
| 32 | 28 | Dismantling of frame work timber scantling 40 Sq cm and over in section in any position complete all as specifed and directed. | | 1 | Cum |
|---|
| 33 | 29 | M&L 2nd class hard wood, clean sawn, in scantling timber frame and fixed with nails complete all as specifed and directed. | | 1 | Cum |
|---|
| 34 | 30 | Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed of CM 1:4, complete all as specified and directed by Engineer-in-charge.. | | 150 | Sqm |
|---|
| 35 | 31 | Ditto all as per item no 30 above but as in skirting over and including 10mm thick cement plaster in CM (1:4) and ditto | | 15 | Sqm |
|---|
| 36 | 32 | Material and labour for non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed. | | 200 | Sqm |
|---|
| 37 | 33 | Material and labour for glazed ceramic coloured tiles of size 300x200x7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match with the shade of tiles laid over and including 10mm thick cement plaster in CM (1:4) complete all as specified and as directed. | | 100 | Sqm |
|---|
| 38 | 34 | Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. | | 300 | Sqm |
|---|
| 39 | 35 | M & L rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound @ 3% by wt of cement finished fair faces of brick/concrete surfaces even and fair without using extra cement . The work will be carried out upto tripple storey building the rate of scafolding is included for this item also. WPC will be measured and paid separately. | | 300 | Sq.m |
|---|
| 40 | 36 | Supply only integral water proofing compound ( ISI marked ) | | 25 | Kg |
|---|
| 41 | 37 | M&L preparation of newly plastered surfaces of walls & applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified. | | 300 | Sqm |
|---|
| 42 | 38 | M&L for preparation of new plastered surface & applying two coats of oil bound distemper (OBD) over a coat of white chalktening on wall complete all as specified and directed by Engineer-in-charge. | | 300 | Sqm |
|---|
| 43 | 39 | M/L for 3 mm thick Birla white putty/JK white wall care putty on walls. | | 90 | Sqm |
|---|
| 44 | 40 | Taking up or down steel tubing 15mm bore and connections including cleaning for refixing and deposited to stores complete all as specified and directed. | | 150 | RM |
|---|
| 45 | 41 | Taking up or down steel tubing 20mm bore and connections including cleaning for refixing and deposited to stores complete all as specified and directed. | | 100 | RM |
|---|
| 46 | 42 | Supply and fix 15mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. | | 150 | RM |
|---|
| 47 | 43 | Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd. | | 100 | RM |
|---|
| 48 | 44 | M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth. | | 10 | RM |
|---|
| 49 | 45 | M & L in repair 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. | | 100 | RM |
|---|
| 50 | 46 | M & L repair for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. | | 100 | RM |
|---|
| 51 | 47 | S & F in repair 110mm bore PVC (SWR) bends any radius complete all as specified and directed. | | 20 | Each |
|---|
| 52 | 48 | S & F 75mm bore PVC (SWR) bends any radius complete all as specified and directed. | | 20 | Each |
|---|
| 53 | 49 | S & F 110mm bore PVC (SWR) branch piece single (Single Y equal or unequal) complete all as specified and directed. | | 15 | Each |
|---|
| 54 | 50 | Supply and fixing as in replacement 75mm bore PVC (SWR) floor trap (ISI Marked), outlet with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (using 20mm graded store aggregate) and making good the disturbed surface to match with existing complete all as specified and as directed by the Engineer-in-Charge.Make : Prince/Supreme/Finolex. | | 15 | Each |
|---|
| 55 | 51 | Supply and fixing 20mm bore Gun metal gate valve with iron wheel head and gun metal spindle screwed both ends after and including taking up or down old unserviceable valve complete all as specified and as directed.\nMake : Leader/Audco/Zoloto. | | 25 | Each |
|---|
| 56 | 52 | Supply & fixing as in repair 15mm Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engr-in-Charge. | | 100 | Each |
|---|
| 57 | 53 | Supply and fixing as in replacement for 15mm Stop valves fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed\n complete all as specified and as directed by the Engr-in-Charge.\nMake : Essco Cat No 513A/513B or equivalent aproved make. | | 30 | Each |
|---|
| 58 | 54 | .-Ditto- all as per item No 53 above but of size 20mm bore and -ditto-. | | 20 | Each |
|---|
| 59 | 55 | S&F in repairs concealed stop valve, cast copper alloy, with crutch or butterfly handle, screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe all as directed. | | 10 | Each |
|---|
| 60 | 56 | S&F in repairs for 15mm dia of pipe Angle valves (concealed type),fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .\n | | 20 | Each |
|---|
| 61 | 57 | Supply and fix as in replacement of 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by the Engr-in-Charge. \nMake : Essco, Cat No DLX-508 or equivalent approved make | | 20 | Each |
|---|
| 62 | 58 | Supply and fix as in replacement of 15mm bore Brass CP Mixture for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed by the Engr-in-Charge. \nMake : Essco, or approved make | | 15 | Each |
|---|
| 63 | 59 | S&F in repair soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick , fixed to walls with plugs & CP brass screws complete all as specified and directed. | | 25 | Each |
|---|
| 64 | 60 | S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed. | | 64 | Each |
|---|
| 65 | 61 | S&F in repairs CP toilet paper holder as approved by GE. | | 25 | Each |
|---|
| 66 | 62 | S&F in repairs peg set of Six chromium plated including fixing screw Make : Prayag | | 25 | Each |
|---|
| 67 | 63 | S & F in repairs waste coupling of PTMT (half or full threaded) 32 mm dia ,complete all as specified and as directed. | | 50 | Each |
|---|
| 68 | 64 | S & F in repairs waste coupling of PTMT (half or full threaded) 40 mm dia ,complete all as specified and as directed. | | 50 | Each |
|---|
| 69 | 65 | S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed. | | 100 | Each |
|---|
| 70 | 66 | Supply and fixing as in replacement 125mm dia brass chromium plated shower rose with revolving joints fixed to 15mm bore GI Pipe complete all as specified and as directed. Make :- ESSCO Cat No EOS-542A or equivalent approved make. | | 50 | Each |
|---|
| 71 | 67 | Supply and fixing as in replacement brass chromium plated towel rail 600mm long fixed with and including Chromium plated brass screws complete all as specified and as directed. Make : ESSCO Cat No A CN 1111 or equivalent approved make. | | 20 | Each |
|---|
| 72 | 68 | Supply and fixing as in replacement brass chromium plated towel rail Circular type fixed with and including Chromium plated brass screws complete all as specified and as directed. | | 15 | Each |
|---|
| 73 | 69 | Supply and fixing as in replacement 100mm dia grating doom with waste hole of PTMT (minimum weight 25gms) complete all as specified and as directed by the Engr-in-Charge. Make: Prayag / Polytuf | | 30 | Each |
|---|
| 74 | 70 | Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed | | 6 | Each |
|---|
| 75 | 71 | Supply and fixing as in replacement vitreous China wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with coloured PVC seat cover and making all necessary connections complete as specified and as directed by the Engineer-in-Charge. \nMake: Parryware Cat No C0278 for water closet, Cat No C8071 EWC Standard for PVC seat cover or equivalent approved make. | | 5 | Each |
|---|
| 76 | 72 | S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap. | | 6 | Each |
|---|
| 77 | 73 | Supply and fixing as in replacement 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed by Engineer-in-Charge. | | 20 | Each |
|---|
| 78 | 74 | Supply and fixing as in repair 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed.\n Make: Prayag Cat No : 323 or equivalent approved make. | | 100 | Each |
|---|
| 79 | 75 | S&F in repairs Plastic water closet seat, black, closed patterns with flat bottom, and cover and mild steel chromium plated or aluminised hinging device | | 20 | Each |
|---|
| 80 | 76 | S&F Sheet glass assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 600 mm long | | 50 | Each |
|---|
| 81 | 77 | Material and labour as in replacement looking mirror of size 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. Make : Saint Gobain/Modi float /Atul / Kohinoor. | | 40 | Each |
|---|
| 82 | 78 | S & F stainless steel sink, 1mm thick for kitchen with draining board with plug and PVC waste pipe including bedding in cement mortar, fixing brackets overall size 915x460mm, bowl size 410x330x 160mm, as fixed in repairs complete all as specified and directed.\n(Make: Jayna Cat No SBSD-05 or equivalent approved make of Hindustan/A one//Blue Star/Jayna) | | 10 | Each |
|---|
| 83 | 79 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning the complete inner surface by rubber/nylon scraper to remove sludge/silt and washing with bleaching power solution and then clear water, etc. and hoisting in postion if required reconnecting and re-fixing in position exc 250 but n exc 500 ltrs. | | 40 | Each |
|---|
| 84 | 80 | Dismantling water tanks and removing to store exc 250 ltr but n exc 500 ltr | | 5 | Each |
|---|
| 85 | 81 | all as per item No 80 but n exc 1000 ltr | | 5 | Each |
|---|
| 86 | 82 | Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 500 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections complete all as specified and as directed by the Engr-in-Charge.\nMake : Syntex/Polywell/Polycon | | 5 | Each |
|---|
| 87 | 83 | Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 1000 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections complete all as specified and as directed by the Engr-in-Charge.\nMake : Syntex/Polywell/Polycon | | 5 | Each |
|---|
| 88 | 84 | S&F 0.71 mm thick plain aluminium sheeting , alloy 31000 H4 in ridges, hips , valley gutter , drip and straight flashing . | | 20 | Sqm |
|---|
