Various Civil Work , Topiary Figures , Swings , Gym Equipments At Various Location I . E . Sunset Point Garden Area Etc . For Devdelopment And Beautification Of Nagadari Hills In Historical Mandore Garden Campus , Jodhpur, Jodhpur-Rajasthan

TDR : 27574848

Tender Notice
BOQ

Expired

Jodhpur , Rajasthan

Tender Brief : Various Civil Work , Topiary Figures , Swings , Gym Equipments At Various Location I . E . Sunset Point Garden Area Etc . For Devdelopment And Beautification Of Nagadari Hills In Historical Mandore Garden Campus , Jodhpur

Document Fees
₹ 500 /-

EMD
₹ 198860.0 /-

Tender Value
Refer document

Submission Date
09-04-2021

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

Name of Work: Various Civil work,Topiary Figures,Swings,Gym Equipments at various location i.e.Sunset Point Garden area etc. for Devdelopment & Beautification of Nagadari Hills in Historical Mandore Garden Campus, Jodhpur.
1	1	Dismantling tile work in floors and roofs laid in cement mortor including stacking of serviceable material and disposal of unserviceable material within 50 meter lead : For thickness of tiles 10 mm to 25 mm.\nAt Mandore Garden	BI01010001010000000000000515BI0100001113	100	Sqm
2	2	Dismantling stone rubble masonry including stacking of serviceable material and disposal of unserviceable material within 50 meters In Cement mortar.	BI01010001010000000000000515BI0100001114	184.5	Cum
3	3	Fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:4 ( 1cement : 4 coarse sand) with joints finished flush. Red Sand stone size not less than 1350 Cm2, a) 40mm	BI01010001010000000000000515BI0100001115	1099	Sqm
4	4	Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils	BI01010001010000000000000515BI0100001116	282.2	Cum
5	5	Carriage of Earth, Sand ,line morrum, manure or sludge Lead above 1 KM. Upto 10 KM.	BI01010001010000000000000515BI0100001117	522.2	Cum
6	6	Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering All up to plinth level IS 456-2000: 1:3:6 (1Cement :3 Course Sand :6 Graded stone aggregate 20 mm nominal size)	BI01010001010000000000000515BI0100001118	213.9	Cum
7	7	Random Rubble stone masonary for foundation and plinth in Cement Sand Mortar above 30 Cm. thick wall IS 1597 (Part-I) 1992 in : Cement Sand Mortar 1:6 (1-Cement:6-Sand).	BI01010001010000000000000515BI0100001119	92.48	Cum
8	8	Random Rubble stone masonary for superstructure above plinth level one storey height above 30 Cm. thick walls IS 1597 (Part-I) 1992 in : Cement Sand Mortar 1:6 (1-Cement:6-Sand).	BI01010001010000000000000515BI0100001120	238.82	Cum
9	9	Extra for facing as per design and detailed specifications IS 1597 (Part-II) 1992 including additional cost of stones over item No. 6.1 & 6.2 for : Course rubble facing Second Sort.	BI01010001010000000000000515BI0100001121	545.13	Sqm
10	10	Rough chisel dressed stone flooring over 20mm (Av.) thick base in CM 1:6 including pointing with cement mortar 1:2 (1-Cement:2-stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm:45 mm thick white sand stone.	BI01010001010000000000000515BI0100001122	90	Sqm
11	11	Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished: 25 mm thick.	BI01010001010000000000000515BI0100001123	258	Sqm
12	12	Providing and laying Chequerred plain cement concrete embossed specially manufactured non-slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1:6 jointed with neat cement slurry complete. Add extra for chequerred coloured plain cement concrete or specially manufactured non-slipping tiles of approved make 20 mm thick.	BI01010001010000000000000515BI0100001125	200	Sqm
13	13	Providing and fixing Jodhpur Red stone jali (three line dressed) with thambali as per the picture shown and as per the old pattern as constructed at canal bridge of Mandore garden. Height of middle portion of jali is 21\", width at middle portion is 7.5\" , thickness of bottom and top portion is 9.5\" (bottom design stone in 2 pieces as per old design and bottom & top dasa made perfectly even). Work must be done as per the old design approved by engineer incharge including cost of material, labour and chiesel dressing (talpai).	BI01010001010000000000000515BI0100001126	90	m
14	14	Supply and fixing Jodhpur sand stone Machine cut Kerb stone (10cm wide 40 cm. height) fixed in white cement sand mortar 1:4 with pigment including EarthWork.	BI01010001010000000000000515BI0100001127	64	Mtr.
15	15	Clearing grass and removal of rubbish maximum 150mm in thickness upto a distance of 100 Mtr outside the periphery of the area by manual means . Note ; where only grass is met with , the area clear shall be measured & paid for under this item ( MORTH clause 201 )	BI01010001010000000000000515BI0100001128	0.12	Hectare
16	16	Cutting & moulding by hand power grinder including polishing etc. complete in all type of Kota/ Marble/ Granite/ Jodhpur stone etc. 25 mm.	BI01010001010000000000000515BI0100001129	4100	Mtr.
17	17	Providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.\nAdd extra if square, rectangular hollow tubular sections are used.	BI01010001010000000000000515BI0100001130	1100	Kg.
18	18	P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. 1000 litres capacity.	BI01010001010000000000000515BI0100001131	3	Nos.
19	19	P & F European type white glazed vitreous china Ist quality W.C. pan (IS:2556 Mark) with P or S trap including cutting and making good the wall and floor.	BI01010001010000000000000515BI0100001132	1	Nos.
20	20	P & F water closet Seat Covers with brass hinges complete IS 2548-1996 : Solid PVC (ISI marked) grade-I White for EWC.	BI01010001010000000000000515BI0100001133	1	Nos.
21	21	P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : WVC with C.P. brass bend.	BI01010001010000000000000515BI0100001134	1	Nos.
22	22	P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : Size 580 mm x 430 mm	BI01010001010000000000000515BI0100001135	3	Nos.
23	23	P&F towel rail or ring of approved quality /make: C.P. brass Towel rail elbow type with concealed screws size 600mm (heavy duty)	BI01010001010000000000000515BI0100001136	3	Nos.
24	24	P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked).	BI01010001010000000000000515BI0100001137	4	Nos.
25	25	P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : C.P. Brass Long body, 15 mm nominal bore weight not less than 690 gm.	BI01010001010000000000000515BI0100001138	3	Nos.
26	26	Construction of manhole in all type of soil inner size 90 X 60 Cm. thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring,making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C.flooring , 25 Kg. CI cover with frame of 40mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth upto 0.5mtr	BI01010001010000000000000515BI0100001139	3	Nos.
27	27	P & F 15 mm. Dia Connection pipe of approved quality/make: C.P. Brass Pipe with CP Brass nuts upto length 600 mm.	BI01010001010000000000000515BI0100001140	2	Nos.
28	28	Renewing glass panes, with puty and nails wherever necessary: 4 mm thick plain glass panes.	BI01010001010000000000000515BI0100001141	40.44	Sqm
29	29	Providing and fixing Granite stone slab mirror polished and machine edge cut in Walls, Pillars, Steps, Shelves, Sills, Counters. Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing of IS 3316-1974 : Jhunjhunu / Jalore (Red / Choclate Colour) Above 3601 Cm2 Slab	BI01010001010000000000000515BI0100001142	2.25	Sqm
30	30	Marble stone flooring table rubbed, 18-20 mm thick over 20 mm (Av.) thick base of CM 1:4 (1-Cement:4-coarse sand) jointing with white cement mortar 1:2 (1-White cement:2-marble dust) with pigment to match the shade of the marble slab including grinding rubbing and polishing complete IS 1130-1969. Makrana second quality plain. Upto 801 to 1500 Cm2 Tiles	BI01010001010000000000000515BI0100001143	10.8	Sqm
31	31	Deep groove pointing on stone masonry in white cement sand mortar (1:3) with colour pigment of approved shade for all type of masonry incl. racking of joint as per specification complete in all respect.	BI01010001010000000000000515BI0100001144	1300	Sqm
32	32	Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete IS 2571-1970 : 50 mm thick with 20 mm thick nominal size aggregate.	BI01010001010000000000000515BI0100001145	360	Sqm
33	33	Providing & fixing of Topiary figures as shown in picture in different shape make by GI Hot dip wire size 10 No. Gauge and bar size 10mm TMT and other material as required, fixing with cement concreat with ratio of 1:2:4 complete in all respect directed by Engineer incharge\n(A) Horse size 9 Ft Length and Height 8 Ft	BI01010001010000000000000515BI0100001146	2	Each
34	34	Cow size 7 Ft Length and Height 6 Ft	BI01010001010000000000000515BI0100001147	2	Each
35	35	Giraffe size 10 Ft Length and Height 12 Ft	BI01010001010000000000000515BI0100001148	2	Each
36	36	Giraffe size 9 Ft Length and Height 9 Ft	BI01010001010000000000000515BI0100001149	2	Each
37	37	Elephant size 8 Ft Length and Height 8 Ft	BI01010001010000000000000515BI0100001150	2	Each
38	38	Elephant size 6 Ft Length and Height 6 Ft	BI01010001010000000000000515BI0100001151	2	Each
39	39	Welcome Elephant size 7 Ft Length and Height 5 Ft	BI01010001010000000000000515BI0100001152	2	Each
40	40	Camel size 9 Ft Length and Height 12 Ft	BI01010001010000000000000515BI0100001153	2	Each
41	41	Camel size 8 Ft Length and Height 9 Ft	BI01010001010000000000000515BI0100001154	2	Each
42	42	Frog size 3 Ft Length and Height 2 Ft	BI01010001010000000000000515BI0100001155	2	Each
43	43	Kangaroo size 7 Ft Length and Height 6 Ft	BI01010001010000000000000515BI0100001156	2	Each
44	44	Butterfly size 6 Ft Length and Height 4 Ft	BI01010001010000000000000515BI0100001157	2	Each
45	45	Peacock 7 Ft Length and Height 5 Ft	BI01010001010000000000000515BI0100001158	2	Each
46	46	Deer 6 Ft Length and Height 5 Ft	BI01010001010000000000000515BI0100001159	2	Each
47	47	Supply and fixing of ornamental and floral garden benches with PWD Logo as shown in picture of decorative cast iron (Fe-15 grade as per IS:2101:1993 standard amended upto date) sides with 12 Nos. of M.S. tubuler pipe of size 65 x 22 mm medium section with provision of grouting at all the four base ends one M.S. support at middle of the benches for extra strength and durability Benches ends suitably grinded for smooth surface finish and primer coated and painted with coloured with wooden powder coated (polyurthane type of powder paint) over all length 150 Cm., 70 Cm. width and 80 Cm height having over all weight 50.00kg +-05% Kg.	BI01010001010000000000000515BI0100001160	100	Each
48	48	Double Swing : Swing in which two children can enjoy at one time. The arch shaped side frame is made of 75mm NB 'B' Class GI pipe and top pipe is made up of 50mm NB 'B' Class GI pipe. The frame is powder coated to give an aesthetic look. The swing is made up of 5mm thick anti skid canvas top. The rubber belt seat is suspended on 6mm rubber coated GI chain. The ball bearings shall be mounted inside a specially designed nylon clamp. Frame pipes firmly embeded in ground by 60 cm. depth in M-15 CC block.\nHeight of swing 2.60 mtr.\nDistance between frame post 1.80 mtr.\nDistance between frames 3.20 mtr.	BI01010001010000000000000515BI0100001161	2	Each
49	49	Deluxe Slide : Deluxe Slide chute is made from stainless steel (SS) of 304 grades with 16 SWG sheet. The structure comprises of 20mm NB and 25mm NB 'B' Class GI pipe. The centre support is made in 100mm NB 'B' Class GI pipe and 15mm NB GI pipe. The ladder cum railing is made up of 20mm NB and 25mm NB 'B' Class GI pipe. The platform is made up of 14 SWG Aluminium sheets with anti skid for firm foot grip. There are triangular steps of 16 SWG sheets. The chute has its end such as it causes safe landing of the child. The pipes are powder coated to aviod rusting. Structure firmly fixed in ground in M-15 CC blocks.\nOverall length of slide 4.88 mtr. (16 Ft.) \nWidth 0.90 mtr. riser 0.25 mtr.\nHt. of platform 2.13 mtr (7 Ft)	BI01010001010000000000000515BI0100001162	2	Each
50	50	Providing and Fixing of FRP WAVE SLIDE its required area 4.6 mtr x 0.9 mtr plat form height should be 5' Ground Level and should be made by 32mm NB and 25 NB and 20 mm NB pipe MS pipe slide Length 10' all components paint by PU paint in multi colours. Structure firmly fixed in ground in M-15 CC blocks.	BI01010001010000000000000515BI0100001163	2	Each
51	51	Spiral Slide : The chute of the Sprial Slide is made of FRP (Fibre Reinforced Plastic) having thickness of 4mm. Slide centre support shall be 80mm NB 'B' Class GI pipe. Landing module shall be supported by 20mm NB 'B' Class GI pipe. Slide extension platform is made form FRP (Fibre Reinforced Plastic). The ladder main frame is 25mm NB GI pipe. The railing shall be made from 15mm NB and 20mm NB 'B' Class GI pipe. All powder coated to aviod rusting. Structure firmly fixed in ground in M-15 CC blocks.\nLength of slide - 3.6 mtr.\nWidth 0.90 mtr.\nRiser 0.25 mtrs.\nHt of slide 1.80 mtrs.	BI01010001010000000000000515BI0100001164	2	Each
52	52	Providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. Add extra if square, rectangular hollow tubular sections are used.	BI01010001010000000000000515BI0100001165	1830	kg
53	53	Painting with enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.	BI01010001010000000000000515BI0100001166	400	Sqm
54	54	Painting with enamel paint of approved brand and manufacture to give an even shade: One or more coats on old work.	BI01010001010000000000000515BI0100001167	205.2	Sqm
55	55	Welding by electric plant.	BI01010001010000000000000515BI0100001168	500	Per Cm length.
56	56	Dustbin of Stain less steel with Dustbin tank of size 700 mm. (Ht) and 350 mm dia. Of 1 mm thick SS sheet. Dustbin frame of 1.20 mm thick SS square pipe of size 40X40 mm, Ht 1200 mm., upper cover size 500X500 mm of 1 mm thick SS Sheet including fixing system of nut and bolts (The drum is mounted on movable round hinges to provide it complete rotation to facilitate the garbage romoval and safe from monkey etc.)	BI01010001010000000000000515BI0100001169	30	Nos.
57	57	Dustbin of HDPE material with roller as shown in picture of size \nSize :-1370 x 1060 x 1340 mm\nWeight :- 55 KG\nMaterial :- HDPE\nColour :- Green\nCapacity :- 1100 ltrs\nLoad capacity :- 440 kgs	BI01010001010000000000000515BI0100001170	20	Nos.
58	58	SKY Walker : \nArea 1.72 mtr x 0.63 mtr\nSafe Area : 2.54 mtr x 1 mtr\nProviding and fixing sky walker made from \"B\" Class GI Pipe the main frame pipe is of a dia 100 mm made from \"C\" Class G I pipe. the outer ring of sky walker is of 32 mm dia made from \"C\" Class G I Pipe for connecting the handle frame to main pipe of 60 mm dia\"C' Class G I Pipe is used. the bottom support of MS round plate of 250mm x 10mm dia thickness is welded at bottom. the leg movement frame is of 50 x 50 mm x 2 mm thick CRC square pipe. Tha handle frame is of 40 mm dia made from \"C\" class G I pipe. The foundation used for fixing is 80 x 40mm x 3 mm thickness C-channel. the footrests is made from aluminum casting material, its sizes are 130x310x5 mm. closing caps made from top quality FRP material with 5 mm thickness & Plastic cap are used. The pins used are made up of 25mm dia bright bar. the bearings used are 6205zz & 6203zz permanent libricated sealed bering of reputed make. high tensile steel with galvanized nut bolts are used for assembly. the secrlips used for assembly are of 25mm dia. the powder coat is done by poly urethane & epoxy powder giving 60 to 70 micron thickness.	BI01010001010000000000000515BI0100001171	2	Nos.
59	59	Leg press : Area 0.40 x 1.77 mtr\nSafe Area : \nLeg Press: Providing, designing and fixing of leg press of size 2000 x 550 x 1600 mm fabricated with main post of 125mm dia and 3.0mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessaryand dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars to be provided with high quality grip rubber on top end. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Seat and base plate cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and\nself lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent\nunwanted movements. All open ends of pipe to be closed by GI/LLDPE caps for user safety. The equipment to be fixed on ground. Structure firmly fixed in ground in M-15 CC blocks.	BI01010001010000000000000515BI0100001172	2	Nos.
60	60	SIT UP BOARD: \nDimensions: 1820 MM (Length) x 430 mm (width) x 580 mm (height)\nSafe Area :- 2.8 mtr x 0.6 mtr.\nsit up board equipment made from \"B\" class GI pipe of different NB\nNB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. \nthe main frame is of 75 mm NB made from \"B' class G I Pipe supported with the M.S. round plate of ø 250 x 10 mm thickness. Fibre reinforced plastic sheet of 3 mm thickness is bounded on 25 mm NB (G.I.) \"B\" class pipe of main frame \nthe base support of the sit up board is made 40 mm NB (G.I.) \"B\" class pipe\nThe foundation used for fixing is structure and made from center pipe of GI of 80 mm\nNB \"B\" class welded with MS. round plate of ø250 mm & 10 mm thick main pipe. \nSupported with 25 mm x 25 mm M.S. angles of 3 mm thickness and 20 mm x 40 mm\nCRC square pipes of 3 mm thickness\nThe powder coating is done with pure polyester powder paints with 60 to 70 micron thickness of paint approved brand by Engineer incharge.	BI01010001010000000000000515BI0100001173	2	Nos.
61	61	Rower :\nArea : 1.2 x 1 mtr\nSafe Area : 1.5 x 1.5 mtr\nProviding and fixing rower made from \"B\" class G.I. pipe the main frame is of 100 mm x 40 mm & 40 mm x40mm CRC pipe with 2 mm thickness the handle frame is of 32 mm dia \"C' class GI pipe the foundation used for fixing consists the three equal items i.e. of 40 mm dia made from \"C\" class GI pipe, C channel of 75 mm x 40 mm x 5 mm & 25 mm X 25 mm x 3 mm M.S. angle to join the movement frame to main frame seamless pipe of 50 mm dia & 3 mm thickness is used. the seats which are fitted on the main frame is made up of high equality FRP material of size 330 mm x 300 mm of thickness 3 mm & MS plate of size 250mm x 200 mm x 5mm is used to support it. cloosing caps are made from top quality FRP material which is of 2 mm thickness. the pins used are made up of 17 mm dia hardened bright bar. the bearnings used are of 6203zz permanent lubricated sealed bearing of reputed mde the handles used are of rubber grip high tensile steel with galvanized nut bolts are used for assembly in the bushes (stopper) used to avoide the collosion. the serclips used for assembly is of 17 mm dia. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness.	BI01010001010000000000000515BI0100001174	2	Nos.
62	62	SURF BOARD\nDiamensions : 910 mm (Length) x 860mm (width) x 1400 mm (height)\nSafe area : 1.39 x 1.27 mtr\nSurf board equipment made from \"B\" class GI pipe of different NB. \nNB stands for nominal bore sizes i.e. internal diameter of pipe is millimeters.\nThe center pipe is of 15 mm NB made from \"B\" Class GI pipe. The sleeve pipe is of 125 mm OB seamless pipe with thickness of 05 mm and bolted to main frame with M 10 SS bolts. \nThe bottom support welded of M.S. plate of 250 mm dia & 10 mm thickness. \nThe handle frame is of 25 NB made from \"B\" Class G I Pipe \nThe handle frame is of 50 NB made from \"B\" Class G I Pipe is supported with 70 x 8 mm bend m.S. flat and can be replaceable. The foundation used for fixing is a structure and made from center pipe of GI of 80 NB \"B\" class welded with MS. round plate of 250 mm dia & 10 mm thick. main pipe supported with 25 mm x 25 mm M.s. angles of 03 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness Bushes are used 70 mm outer diameter with 05 mm thickness is used. \nthe footrests made from injection moulded plastic LLDPE/HDPE for Support to footrest 200mm x 250mm with 3mm thickness M.S. plate used. \nClosing caps are made up of injection moulded plastic LLDPE/HDPE. \nThe pins used are made up of 35 mm dia SAE 8620 bright material \nThe bearing used are of :6007zz permant lubricated sealed bearing of reputed brand. \nHigh tensile steel with galvanized nut bolts are used for assembly. \nThe cerclips used for assembly is of A 34. \nThe power coating is done with pure polyester power of ackzonoble or berger with 60 to 70 micron thickness.	BI01010001010000000000000515BI0100001175	2	Nos.
63	63	AIR WALKER :\nMACHINE PART DESCRIPTION OF THE AIR WALKER \n(A) Mounting plate \n(B) Center pillar \n(C) Trapezium shaped pipe \n(D) Cap \n(E) Holding pipe \n(F) Hings supporter \n(G) Outuse L shaped pipe \n(H) Rectangular pipe \n(I) Standing pad\n(J) Triangular hinge supporter \n1. A circular mounting plate of diameter 233 mm and thickness 8 mm 4 holes on this plate at 90 degree of which PCD 170 mm hole diameter is 20 mm.\n2. On circular moving plate a center pillar is welded. diameter of center pillar is 125 mm and height is 233 mm. \n3. Jrapezium shapped pipe is welded to the center pillar from the middle at the base. Jrapezium shapped pipe's upper portion is open with two branches. \n4. Cap is on the two branches of upper portion/top of the branches are 925 mm wide and length of each branch is 885m. At the base of the branches the gap is 925 mm with a redius bend 235mm. \n5. open end of trapezium shaped pipe is welded with a holding pipe. Holding pipe has a straight length of 810mm and a 90 degrees radius on the both sides, then a small straight length of 246 mm. through this small straight length holding pipe is welded to trapezium shaped pipe. Holding pipe is welded at an angle of 40 degrees to the open ends of trapezium shaped pipe height of joint is 1212mm \n6. Hinge support of length 126 mm is welded on the branches of trapezium shaped pipe at a height of 1117 mm from the base. \n7. 2 obtuse L shaped pipes are connected to the hinge supporter by the bushes. Bushes are welded at the upper portion of the obtuse L shaped pipe, lower portion of obtuse L shape pipe is welded with rectangular pipe of length 705 mm, radius 124 mm and short length 137 mm \n8. on rectangular pipe standing pad are tightly screwed standing pad (foot rest) can be of plastic or metal. \n9. Triangular hinge supporter are welded to the hinge supporter to provide better strength.\nNote : All the movable joints have a PIN Bearing in between, tightened with the allen bolt poly drive head bolt having plastic caps on the ends since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.	BI01010001010000000000000515BI0100001176	2	Nos.
64	64	TRIPE HIP TWISTER :\nmachine parts description of tripe hip twister \n1. Mounting Plate \n2. Center pillar \n3. plastic cap \n4. circular handle \n5. connecting rod \n6. floor rest pipe \n7. standing pad \nfoundation of machine is cemented and bolted with base channel and circular \nMounting plate which dimension is below : \n1. Measurement of base channel is 3'x6\"x2\" \n2. Circular mounting plate's diameter 233 mm and thickness is 8mm. 4 hole on this plate at 90 degree which PCD is 170 mm hole diameter is 20mm \nMechanical dimension and measurement of machine are following : \n1. A circular mounting plate which dimension is same of above circular mounting plate and it is tightened with nut and bolt.\n2. On this circular mounting plate a center pillar is welded. Diameter of center pillar is 150 mm and height is 1288mm.\n3. Plastic cap is fixed on the top of center pillar and tightened with help of screw. Diameter and height is 120mm and 69mm. \n4. Circular handle is welded at the height of 1171 mm from the base of circular mounting plate. OD of circular plate is 557 and ID is 493mm. Three pipe rod which diameter 32mm are welded at 120 degree. \n5. Connecting rod for floor rest pad which diameter is 48mm. It is being bended after 131mm at angle of 30 degree and bending radius is 124. Bending length is 185mm. Again it is being bended at angle of 30 degree and bending radius 76. Bending length is 71mm. Three pipes of same dimensioris are welded at the angle of 120 degree and collinear to 32 diameter's pipe rod of circular handle.\n6. Three floor rest pipe which diameter 114 mm and height 105mm and welded at linear center with each connecting rod. \n7. Three plastic standing pad which diameter is 280mm and height is 36mm and attached with each floor rest with help of ball bearing which OD 60mm. All plastic standing pad and floor rest pipe is connected with shaft which diameter is 28mm. \nNote : All the movable joints have a PIN Bearing in between, tightened with the Allen bolt polydrive head bolt having plastic cap on the ends. Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.	BI01010001010000000000000515BI0100001177	2	Nos.
65	65	CHEST PRESS CUM SEATED PULLER : \nDimensions : 2000mm(length)x 710mm (width) x 2200 mm (height)\nSafe Area : 3.00 mtr x 1.7 mtr.\nChest press cum seated puller equipment made up of \"B\" Class G I pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters.\nThe center pipe is of 125 NB made up of \"B\" class G.I. pipe. \nThe bottom welded with support of M.S. round plate of ? 250 mm & 10 mm thickness. \nThe connecting pipes are made up from 25 NB \"B\" Class GI pipe. \nThe handle frame is made up from 32 NB \"B\" Class GI pipe \nTo build structue bushes are used which are mde fro seamless pipe of 50mm OD and 6 mm thickness as well as 50 mm diameter solid bar is used. \nThe foundation used for fixing is a structure and made from Center pipe of GI of 80 NB \"B\" Class welded with MS round plate of ?250mm & 10 mm thick. Main pipe supported with 25mm x 25 mm. MS angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 03 mm thickness. \nThe seats and back rests are fitted on the outer frames are made up of MS sheet of size 330 mm x 300 mm x 2 mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. \nClosing caps are made up of injection moulded plastic LLDPE/HDPE. \nFoundation cover cap is made from injection moulded plastic LLDPE/HDPE.\nPins used of diameter 25mm and 17mm are made up from SAE 8620 bright material \nThe bearing used are of \"62052zz\" & \"6203zz\" permanent lubricated sealed bearing of reputed brand. \nHigh tensile steel with galvanized nuts & bolts are used for assembly. \nThe cerclips used for locking is made up of A24 A A16\nThe powder coating done with pure polyester powder from ackzonoble or berger paints with 60 to 70 micron thickness.	BI01010001010000000000000515BI0100001178	2	Nos.
66	66	Multi functional trainer : \n(Single user) \nMachine part description: \n1. Mounting plate 1\n2. Cap \n3. Handle connecting pipe 1\n4. connecting pipe 1\n5. center piller 1\n6. holding pipe 1\n7. holding pipe 2\n8. Movable pipe \n9. Square pipes\n10. Stepping plates \n11. Stepper base \n12. Standing plate \n13. Center pipe \n14. Mounting plate 2\n15. Handle connecting pipe 2\n16. Nylon pad \n17. Hinged pipe 1\n18. Hinged pipe 2	BI01010001010000000000000515BI0100001179	2	Nos.
67	67	Shoulder builder \nMounting plate\nCenter pillar \n2 hinge holding pipe\n2 bending pipe \nCap\n2 U shapped pipes\nHandles \n2 Straight pipe (No. 1) \nStraight pipe (No. 2)\nStraight pipe (No 3)\nSeat base pipe\nSeat bending pipe \nSeat\nBack Seat \nHinge box \nBracket holder\n1. A circular mounting plate of diameter 233 mm and thickness 8 mm, there are 4 holes on this plate at 90 degree which is P.C.D. 17 mm hole diameter is 20 mm. \n2. On Circular Mounting plate a center pillar is welded. Diameter of the center pillar is 119mm and height is 1838mm. \n3. Cap is fixed on the top of the pillar with rivets. \n4. At 1528mm vertical distnace-2 hinges holding pipes are welded in opposite directions. Hinge holding pipes have clear hole for screw at 177mm distance. \n5. Bending pipes are welded to the hinge holding pipes and the center pillar to provide mechanical strength to the hinge holding pipe. \n6. Hinge box is fitted to the hinge holding pipes with a steel screw and bush. Hinge box has a clear hole at the base.\n7. U shapped pipes are welded at the upper part of the hinge box. \n8. At the opening end of the U shapped pipe. handless are fitted with steel screw. \n9. Straight pipe no. 1 is fitted to the hinge box at the base with pin bearing\n10. Lower end of the straight pipe no. 1 is fitted to straight pipe with a pin bearing. \n11. Straight pipe no. 2 and No. 3 are joined to the center pillar and seat base pipe one over the other respectively with a gap of 490mm, through bracket jointers, which are welded to the centre pillar and seat base pipe also. \n12. Seat base pipe is connected with straight pipe no.2 and No. 3 with pin bearing. \n14. Seat and back seat are fitted on the seat bending pipe with pin bearing. These seats are of plastic. \nNote : All the movable joints have a pin bearing in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends . Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.	BI01010001010000000000000515BI0100001180	2	Nos.
68	68	Cycle : \nDimensions : 1570mm(length) x 570 mm (width) x 900 mm (height)\nSafe Area : 2.50 mtr x 1.5 mtr.\nCycle equipment made from \"B\" Class G I pipes of different NB (NB stands for nominal bore size i.e. internal diameter of pipe in millimeters)\nThe main frame of 75 NB made from \"B\" class G.I. pipes.\nM.S. round plate of 300mm & 10mm thickness used to form a paddle assembly.\nThe handle frame is of 25 NB made from \"B\" class G.I. pipe.\nThe seat and back rests are fitted on the outer frames are made up of M.S. sheet of size 330 mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges.\nThe foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB \"B\" class welded with M.S. round palte of 250mm & 10mm thick main pipe supported with 25 x 25 mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.\nClosing caps are made up of injection mounlded plastic LLDPE/HDPE.\nPins used of Diameter 25mm are made up from SAE 8620 bright material.\nPins used of Diameter 13mm are made up from ENB material with CRCA pipe 20x20mm of thickness 3.00mm for paddleassembly.\nThe bearing used are 6001zz & 6205zz permanent lubricated sealed sealed bearing of reputed brand.\nHigh tensile steel with galvanized nuts and bolts are used for assembly.\nThe circlip used for assembly are of A24 type.\nThe powder coating done with pure polyester powders from Ackzonoble or berger paints with 60 to 70 micron thickness.	BI01010001010000000000000515BI0100001181	2	Nos.

Also Visit

Tenders

Rajasthan Tenders

Apparel and Personal Care Tenders

Uniforms Tenders

Uniform Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Various Civil Work , Topiary Figures , Swings , Gym Equipments At Various Location I . E . Sunset Point Garden Area Etc . For Devdelopment And Beautification Of Nagadari Hills In Historical Mandore Garden Campus , Jodhpur, Jodhpur-Rajasthan

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Various Civil Work , Topiary Figures , Swings , Gym Equipments At Various Location I . E . Sunset Point Garden Area Etc . For Devdelopment And Beautification Of Nagadari Hills In Historical Mandore Garden Campus , Jodhpur, Jodhpur-Rajasthan

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us