}

Fish Bolts & Nuts-Nagaland

Northeast Frontier Railway has published Fish Bolts & Nuts. Submission Date for this Tender is 18-06-2020. Screws Tenders in Nagaland. Bidders can get complete Tender details and download the document.




Tender Notice

24600613
Fish Bolts & Nuts
Open Tender
Indian
Nagaland
18-06-2020

Tender Details

Supply Of , Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X370mm With Fish Nuts As Per Drg No. 11532. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X130mm With Fish Nuts As Per Drg No. 11508. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 50.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The 25Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X410mm With Fish Nuts As Per Drg No. 11536. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X310mm With Fish Nuts As Per Drg No. 11526. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X330mm With Fish Nuts As Per Drg No. 11528. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X280mm With Fish Nuts As Per Drg No. 11523. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost., Mild Steel Square Head Fish Bolts And Nuts With 1 No. Of Spring Washer And 1 No. Of Plain Confirming To Is 2062:2011 E 250 Br. The Steel Used In The Manufacture Of The Fish Bolts And Nuts Shall Be Made By The Acid Or Basic Open-Hearth, Duplex Or Acid Bessemer Process And Shall Not Show On Analysis More Than 0.06 Per Cent Of Sulphur Or Of Phosphorus. The Tensile Test On The Steel Used In The Manufacture Of Fishbolts And Nuts Shall Be Made Either On A Test Piece Taken From The Bar Or On A Test Piece Turned From The Finished Bolts. A Test Piece Taken From The Steel As Rolled, Shall, When Cold, Be Capable Of Being Bent, Either By Pressure Or By Blows From A Hammer, Round A Bar Equal To Its Diameter Or Thickness Until Its Sides Are Parallel Without Showing Any Signs Of Fracture. One Tensile And One Cold Bend Test Shall Be Taken From Every 5 Tonnes Or Under Of The Steel As Rolled. Test Pieces Shall Not Be Subjected To Heat Treatment Of Any Kind Before Being Tested. Should Any Of The Test Pieces First Selected Not Fulfil The Tensile And Bend Tests Specified In Clauses 2 And 3, Two Additional Test Pieces May Be Taken, And Should Either Of Them Fail To Fulfil Such Tests, The Steel From The 5 Tonnes Or Under From Which The Test Pieces Have Been Taken Will Be Rejected. The Fishbolts And Nuts Shall Conform To The Dimensions Shown On The Drawings. The Bolt-Heads Shall Be Formed By Upsetting The Bar When Hot. They Shall Be Concentric, Square With The Shank And Cleanly And Properly Finished Without Fin Or Flash. The Eccentricity And Angularity Errors Shall Be Within The Limits Specified In Clauses 5.3 And 5.4 Of Is: 1367-1961. The Bolts Size 25X270mm With Fish Nuts. The Nuts Shall Be Hot Forged From The Solid, The Holes Being Truly Central, And The Faces Square With The Axis Of The Hole As Per Drg No. 11522. Unless Otherwise Specified, The Bearing Faces Of The Nuts Shall Be Faced True In A Machine. The Screw Threads Of The Bolts And Nuts Shall Be Cut To The Profiles Of Indian Standard Screw Threads ( Is: 1362-1962 ) And Shall Conform To%A0the Normal ( Medium ) Tolerances Specified In Is: 1362-1962, And Shall Also Pass The Unscrewing Test Specified In Clause 13. When Nuts Are Ordered Independently Of Bolts And%A0vice Versa, %A0the Threads Of The Nuts Or Bolts As The Case May Be Shall Be To The Same Dimensions And Tolerances. The Fishbolts And Nuts Shall Be Coated With Good Quality Non-Drying Heavy Lubricating Oil Or Alternatively Lanoline - Based Protective Of Approved Quality. Each Bolt Shall Be Coated And Packed Complete With Its Nut, Which Shall Be Screwed On For A Few Threads. They Shall Be Packed In Double Bags, The Inner And Outer Bags Being Made Of New Twilled Jute Sacking Weighing Not Less Than 680 G / Sq.M. No Bag Shall Contain More Than 0.5 Quintal Of N Bolts, And Each Bag Shall Contain The Same Number Of Bolts. The Fishbolts Shall Be Marked With The Makers Initials, Mark And The I.R.S. Part Numbers. Note:-Material Should Strictly Comply To The Given Specifications. In Case Of Any Deviations, The Materials May Be Rejected On Suppliers Own Risk And Cost.

Key Value

Document Fees
Refer document
EMD
Refer document
Tender Value
Refer document
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail