Supply Of Conveyor Belts For Unit- 3 Chp-Karnataka

Supply Of Conveyor Belts For Unit- 3 Chp 1. Conveyor Belt Of The Following Specification 1. Belt Designation, Type, Rating (Strength In Kn/M. Of Belt Width/No. Of Plies):-630/4, Nylon/Nylon, Heavy Duty. 2.Top Cover Thickness:5Mm 3.Bottom Cover Thickness:3Mm 4.Full Belt Width:1400Mm 5.Nominal Thickness Of Carcass: 5Mm Min 6.Dimensional Variation Of Belt 6(A) Cover Thickness:+Open,-0 Is-1891-1994 Pt-1 6(B) Width:+ 1% Is-1891-1994 Pt-1 6(C) Length:+2%, -0.5% Is-1891-1994 Pt-1 7.Tensile Strength Of Full Belt In Warp Direction(Kn/M):630 8. Tensile Strength Of Full Belt In Weft Direction (Kn/M): (157.5 Min.) 9.Elongation Of Full Belt In Warp Direction 9(A) At Reference Load:3% Max Is-1891-1994 Pt-1 9(B) At Break Load:10% Min Is-1891-1994 Pt-1 10.Cover Rubber Properties 10.1 Grade: Fire Resistant 10.2(A)Tensile Strength(Mn/Sq.M) Before Ageing:17Min.Is-1891-1993 Pt-V 10.2(B)Tensile Strength(Mn/Sq.M) After Ageing(Time & Temperature 72Hrs@70+1 0 C) : +10% Of Intial Value-20% Of Intial Value Is-1891-1994 Pt-1 10.3(A)Elongation At Break Before Ageing:400% Min Is-1891-1994 Pt-1 10.3(B)Elongation At Break After Ageing(Time & Temperature 72Hrs@70+1 0 C) : +10% Of Intial Value-25% Of Intial Value Is-1891-1994 Pt-1 10.4 Angular Tear Strength(As Per Astmd624):30N/Mm(Min.) 10.5 Electrical And Fire Resistance Properties 10.5(A) Flame Test:Duration Of Flame With Cover 45Sec Max For 6 Samples 15 Sec Max For Individual No Flame Re-Appearance In Air Current Iso-340 10.5(B) Drum Friction Test: 400Degree C Max Can-Csa-M422-M87(Type-C) 10.5(C)Electrial Resistivity: 300Mega Ohm Max Can-Csa-M422-M87(Type-C) 10.6 Abrasion Resistance:Max Volume Loss 175Mm3 Max Din-53516 10.7 Shore Hardness:71 +/-5 Deg.A 11.Adhesion Property(Min.) 11.1 Top Cover To Ply(In Kn/M Of Width):4.5 Is-1891-1994 Pt-1 11.2 Ply To Ply(In Kn/M Of Width):5.25 Is-1891-1994 Pt-1 11.3 Ply To Bottom Cover(In Kn/M Of Width):4.5 Is-1891-1994 Pt-1 12.Type Of Edge: Moulded Edge Construction 13. Troughability:0.11 Min Is-1891-1994 Pt-1 14. Applicable Standards: Is-1891-1994 Pt-1&V,Can-Csa-M422-M87(Type-C),Din-53516 & Iso-340(Cl-4.2.2.2) 15. Patch Repair Norms: A)All Repair Norms Below 25Mmx25mm Size Shall Not Considered As Repairs B) Not More Than 5 Repairs Per 100Mtr Length Shall Be Permitted,Max.Size Of Repairs Shall Be Contained Within A Square Of 1/5Wx1/5W, Where #W Is Width Of Belt. 16.Length Of Belt In One Roll:200 Mtrs 17.Marking On The Belt: Every 10 Mtrs Interval 18.Packing:Standard Wooden With Steel Core 19.Belt Is To Be Hot Jointed By The Manufacturer Free Of Cost,If Cut For Inspection Inside Of Any Roll Of 250 Mtr To Be Supplied.,

INR 550 /-

INR 12500.0 /-

Refer document